Instruktionsbog
AEN4 Series Angle Nutrunner
| MODEL NR. | GEAR CASE SUB- ASM | ANGLE HEAD ASM. | TRANSDUCER SUB- ASM. | SHIMS |
| AEN4C22014C | 24860 | 24890 | 31048.001 | 24855/24856/24857 |
| AEN4C22024C | 24709 | 24890 | 31048.003 | 24855/24856/24857 |
| AEN4F22029C | 24901 | 27135 | 31048.004 | 21091/21092/21093 |
| AEN4F22036C | 24894 | 27135 | 31045.001 | 21091/21092/21093 |
| AEN4F22043C | 24902 | 27135 | 31045.003 | 21091/21092/21093 |
| AEN4F22055C | 24904 | 27135 | 31045.005 | 21091/21092/21093 |
MONTERINGSVEJLEDNING
UNDERMONTERING
- GEAR & SPLINES: SMØR MED DOW CORNING MOLYKOTE BR2 PLUS FEDT.
- BEARINGS: LUBRICATE WITH CHEVRON SRI GREASE
- O-RINGS: LUBRICATE WITH O-RING LUBE
- APPLY LOCTITE 222 (PURPLE), TIGHTEN TO 1.0 Nm (9 IN-LBS)
| KOMMENTARER | VARENR | DELNUMMER | Antal | BESKRIVELSE |
| 1 | 28766 | 1 | MOTORSAMLING | |
| 2 | SE SKEMA | 1 | GEARKASSE SUB-ASM. | |
| 3 | SE SKEMA | 1 | ANGLE HEAD ASM. | |
| 4 | 28754 | 1 | HÅNDTAG | |
| 5 | 29186 | 1 | COVER, LEVER HANDLE | |
| 6 | 25763 | 1 | TRANSDUCER ADAPTER | |
| 7 | 24780 | 1 | MOTORKOBLING UNDER-ASM. | |
| 8 | SE SKEMA | 1 | TRANSDUCER UNDER-ASM. | |
| 9 | 29202 | 1 | TRIGGER CABLE ASM., 6 PIN – 6 PIN | |
| 10 | 29191 | 1 | TRIGGER/MFG BOARD ASM., 2000-SERIES, GEN 4 | |
| 11 | 28767 | 1 | TOOL CONN. ASM.. | |
| 12 | 30966 | 1 | LED BOARD ASM, I2C | |
| 13 | 24679 | 1 | RETAINING RNG | |
| 14 | 24683 | 1 | SPRING, REV BUTTON | |
| 15 | 25557 | 1 | REV BUTTON SUB-ASSEMBLY | |
| 16 | 29189 | 1 | TRIGGER SUB-ASM. | |
| 17 | 31051 | 1 | DOWEL PIN, 0.094 X.75, GROOVED, STEEL, ZINC PLATED | |
| 18 | 31061 | 2 | DOWEL PIN, Ø3/32 X 1/4, STEEL | |
| 19 | 28760 | 1 | LED DÆKSEL | |
| 20 | 28753 | 2 | MOTOR COVER, SMALL MOTOR O.D. | |
| 21 | 22141 | 1 | SIKKERHEDSMÆRKAT | |
| 22 | 20132 | 1 | GASFJÆR | |
| 23 | 27235 | 2 | O-RING, BUNA-N, #28 | |
| 24 | 23753 | 8 | SCREW, FHSC 6-32×5/16, 18-8 SS | |
| 25 | 27455 | 6 | SCREW, SHC 4-40 x.188, STEEL, BLACK OXIDE | |
| 26 | 26078 | 4 | SCREW, SHC 4-40 X 5/16, BLK OXIDE | |
| P/N 21091 | 27 | SE SKEMA | A/R | SHIM, PINION SHAFT, 002—2000 SERIES |
| P/N 21092 | 28 | SE SKEMA | A/R | SHIM, PINION SHAFT, .005 — 2000 SERIES |
| P/N 21093 | 29 | SE SKEMA | A/R | SHIM, PINION SHAFT, 010-2000 SERIES |
| P/N 24855 | 30 | SE SKEMA | A/R | SHIM..1MM ANGLE HEAD |
| P/N 24856 | 31 | SE SKEMA | A/R | SHIM, 2MM ANGLE HEAD |
| P/N 24857 | 32 | SE SKEMA | A/R | SHIM, 3MM ANGLE HEAD |
| 33 | 23741 | 1 | SHIM, OUTPUT, .002 IN, 40 NM | |
| 34 | 21022 | 1 | SHIM, BLANK OUTPUT SHAFT, 0.005 TΗΚ | |
| 35 | 21021 | 1 | SHIM, BLANK OUTPUT SHAFT, 0.010 TΗΚ | |
| 36 | 20534 | 1 | 2000 SERIAL/MODEL LABEL | |
| IKKE VIST | 37 | 28257 | A/R | CABLE TIE, 1.65mm X 71mm |
| IKKE VIST | 38 | 25471 | 1 | LABEL SN# COVER, .25 X 4″ |
| 39 | 25130 | 1 | SCREW, BHSC,4-40 X 1/4, STEEL | |
| 40 | 50061 | A/R | RTV 3145, CLEAR |
AEN4C22014C, AEN4C22024C TOOL MODELS
AEN4F22029C, AEN4F22036C, AEN4F22043C, AEN4F22055C TOOL MODELS
TOOL MODEL NO.
AEN4C22014C
AEN4C22024C
AEN4F22029C
AEN4F22036C
AEN4F22043C
AEN4F22055C
10000 SE FYRE STREET
PORTLAND, OREGON 97216
503.254.6600
DOKUMENT KONTROL
PRINTED COPIES OF THIS DOCUMENT ARE CONSIDERED TO BE UNCONTROLLED DOCUMENTS. HOLDERS ARE RESPONSIBLE FOR VERIFYING THE CURRENT REVISION LEVEL WITH PURCHASING OR ENGINEERING PRIOR TO USE OR FABRICATION. THE CONTROLLED VERSION OF THIS DOCUMENT IS ELECTRONICALLY MAINTAINED.
PROPRIETÆR OG FORTROLIGT
THIS DRAWING CONTAINS INFORMATION STRICTLY CONFIDENTIAL TO ACRADYNE/AIMCO. IN THE ABSENCE OF EXPRESSED WRITTEN PERMISSION, ACRADYNE/AIMCO HAS LOANED THIS COPY WITH THE MUTUAL UNDERSTANDING THAT (A) IT WILL NOT BE USED FOR ANY PURPOSE OTHER THAN FOR THAT IN WHICH IT WAS PROVIDED, (B) THE DATA CONTAINED HEREINWILL NOT BE DISCLOSED TO OTHERS, (C) IT WILL NOT BE REPRODUCED, AND (D) IT WILL BE RETURNED TO ACRADYNE/AIMCO IMMEDIATELY UPON DEMAND.
| REVISIONSNIVEAU | REVISION UDGIFTSDATO | BESKRIVELSE AF ÆNDRINGER FORETAGET PÅ DEL | ECN # | FORFATTER/ GODKENDELSE |
| REVISIONSBLOK | ||||
MEDMINDRE ANDET ANGIVES, ER DIMENSIONER I TOMMER
DIMENSIONS AND TOLERANCES PER ANSI Y14.5 SURFACE ROUGHNESS PER ANSI Y14.36
BLOKTOLERANCE PR. DECIMAL:
.X = ±.030 .XX = ±.010 .XXX = ±.005 .XXXX = ±.0005
ANGLE = ±0● 30′
REMOVE BURRS AND SHARP EDGES: R.015 MAX
MACHINE SURFACE FINISH: 125 RMS OR BETTER
TEGNINGER OG TEKNISKE DOKUMENTER STYRET AF: ACRADYNE MEKANISK ENGINEERING
ANGLE NUTRUNNER, 3/8″ SQ. DR.
GEN 4 2000 SERIES
| STØRRELSE D |
DEL- / TEGNINGSNUMMER AEN4_220_ _C |
REVISION C |
| SKALA 1:1 | MÅ IKKE SKALERE TEGNING | ARK 2 AF 2 |
Dokumenter/ressourcer
 |
AIMCO AEN4 Series Angle Nutrunner [pdf] Brugermanual AEN4C22014C, AEN4C22024C, AEN4F22029C, AEN4F22036C, AEN4F22043C, AEN4F22055C, AEN4 Series Angle Nutrunner, AEN4 Series, Angle Nutrunner, Nutrunner |