Indledning
Thank you for choosing the BUTURE BC02 Car Jump Starter with Air Compressor. This versatile device combines a powerful jump starter, a portable air compressor, a power bank, and an emergency light, making it an essential tool for any vehicle owner. Please read this manual carefully before use to ensure safe and optimal operation.
Figure 1: BUTURE BC02 Jump Starter and included accessories.
Vigtige sikkerhedsoplysninger
- Bær altid øjenværn, når du arbejder med batterier.
- Do not allow the jump starter clamps to touch each other once connected to the device.
- Start ikke med et frossent batteri.
- Sørg for, at enheden er fuldt opladet før brug for optimal ydeevne.
- Opbevares utilgængeligt for børn.
- Udsæt ikke enheden for ekstreme temperaturer eller fugt.
- Hvis enheden bliver for varm under brug, skal den straks afbrydes.
Pakkens indhold
Tjek venligst pakken for følgende varer:
- BUTURE BC02 Jump Starter with Air Compressor
- Smart batteri Clamps
- Luftslange
- Dyseadaptere (til forskellige oppustelige ting)
- USB-C ladekabel
- Brugermanual
- Opbevaringspose
Opsætning og første opladning
Before first use, ensure the BUTURE BC02 is fully charged. The device features a large LED screen that displays the battery level.
- Connect the provided USB-C charging cable to the USB-C input port on the device.
- Connect the other end of the USB-C cable to a suitable USB wall adapter (not included) or car charger.
- The LED screen will indicate charging status and battery percentage. Charge until the screen shows 100%.
Figure 2: Charging the BC02 and using it as a power bank.
It is recommended to recharge the device every 3-6 months, even if not in use, to maintain battery health.
Betjeningsvejledning
1. Start af et køretøj med startkabler
The BUTURE BC02 can jump start vehicles with up to 9.0L gas engines and 8.0L diesel engines.
- Sørg for, at jumpstarteren er tilstrækkeligt opladet (mindst 50 % anbefales).
- Indsæt det smarte batteri clamp plug firmly into the jump starter's 12V output port. The indicator light on the clamp vil blinke skiftevis rødt og grønt.
- Tilslut den røde (+) clamp til den positive (+) pol på køretøjets batteri.
- Tilslut den sorte (-) clamp til den negative (-) pol på køretøjets batteri.
- Once connected correctly, the indicator light on the smart clamp will turn solid green. If it flashes red or beeps, check connections or refer to the troubleshooting section.
- Start dit køretøj inden for 30 sekunder.
- Once the vehicle starts, immediately remove the smart clamp from the vehicle battery, then disconnect it from the jump starter.
Figure 3: Easy steps to jump start your vehicle.
Funktion til tvungen start: If the battery is extremely low and the smart clamp does not show a solid green light, consult the troubleshooting section for instructions on using the force start function (if available and safe for your vehicle).
2. Using the 150PSI Air Compressor
The integrated air compressor can inflate tires and other inflatables up to 150 PSI with smart preset and auto-stop features.
- Tryk på tænd/sluk-knappen for at tænde enheden.
- Connect the air hose to the inflation port on the device and tighten it.
- Attach the other end of the air hose to the item you wish to inflate (tire valve, ball needle, etc.). Use the appropriate nozzle adapter if necessary.
- Short press the 'M' button to enter inflation mode.
- Press 'M' again to cycle through inflation modes (Car, Motorcycle, Bicycle, Ball, Custom) or 'U' to change pressure units (PSI, BAR, KPA).
- Brug knapperne '+' og '-' til at indstille det ønskede tryk.
- Long press the power button for 3 seconds to start inflation. The compressor will automatically stop when the preset pressure is reached.
- Once inflation is complete, disconnect the air hose from the item and the device.
Figure 4: Steps for using the air compressor.
Inflation Pressure Ranges:
- Car: 26-51 PSI
- Motorcycle: 26-44 PSI
- Bicycle: 30-65 PSI
- Ball: 4-16 PSI
- Custom Inflation: 0-150 PSI
Figure 5: Recommended inflation ranges for various items.
3. Brug som en bærbar powerbank
The BC02 can charge your electronic devices on the go.
- Connect your device's charging cable to the USB-A output port (5V/2.4A) on the jump starter.
- Jumpstarteren vil automatisk begynde at oplade din enhed.
- The USB-C port can also be used for input (5V/2A, 9V/2A, 12V/1.5A) to recharge the jump starter itself.
Figure 6: Charging mobile devices with the BC02.
4. Emergency Lights
The device features a 500-lumen LED light with multiple modes for emergency situations.
- Press the light button once for a steady flashlight.
- Press again for white strobe light.
- Press a third time for red strobe light (warning triangle).
- Press a fourth time for SOS signal.
- Press a fifth time to turn off the light.
Figure 7: Emergency light functions.
Opretholdelse
- Rensning: Tør enheden af med en blød, tør klud. Brug ikke skrappe kemikalier eller slibende materialer.
- Opbevaring: Opbevar enheden et køligt, tørt sted væk fra direkte sollys og ekstreme temperaturer.
- Opladning: Recharge the device every 3-6 months to maintain battery life, even if not in use.
- Batteripleje: Undgå at aflade batteriet helt ofte.
Fejlfinding
Specifikationer
Brugertips
- Always keep the jump starter charged, especially before long trips or during cold weather.
- Familiarize yourself with the different inflation modes and pressure units before an emergency.
- Store the device in an easily accessible location in your vehicle.
- Test the emergency light functions periodically to ensure they are working.
Garanti og support
For garantioplysninger, teknisk support eller serviceforespørgsler, kontakt venligst sælgeren eller producenten direkte. Gem din købskvittering som købsbevis.
