DOMRAEM ESP32 WLED-controller brugermanual

1. Introduktion

The DOMRAEM ESP32 WLED Controller is a high-performance smart lighting controller designed for PWM dimming LED strips. It offers a 'low-threshold professional lighting' experience, allowing direct control of RGBCCT, RGBW, RGB, WW, CW, and monochrome PWM light strips via the WLED dedicated APP or web interface. This controller eliminates the need for a gateway or third-party ecosystem apps, providing 16 million colors with smooth transitions for professional lighting effects. It supports integration with Home Assistant and other platforms.

Nøglefunktioner:

• 5-in-1 Dimming: Supports RGBCCT, RGBW, RGB, WW, CW, and monochrome PWM LED strips.
• WLED App Control: Dedicated WLED APP for intuitive control and customization.
• Multiplatformsunderstøttelse: Compatible with Home Assistant and other open-source platforms.
• WiFi Direct Connection: No gateway required for operation.
• Easy Firmware Update: Upgradeable version (DOM-WLE-ACLE) includes a Type-C programming interface for firmware burning and deep DIY expansion.
• Stemmestyring: Works with Alexa and Google Home Assistant.

2. Vigtige sikkerhedsoplysninger

• Kompatibilitet: This controller is ONLY compatible with PWM dimming light strips (RGBCCT/RGBW/RGB/WW/CW/monochrome).
• DO NOT connect to digital addressable light strips such as WS2812B/SK6812. Connecting incompatible strips may damage the controller and/or the LED strips.
• Strømkrav: Sørg for, at input voltage er inden for området 12-24V DC.
• Strømgrænser: Do not exceed 15A per channel. The total output current for all channels combined must not exceed 20A. Overloading can cause overheating and damage.
• Sikkerhed ved ledningsføring: Always disconnect power to the LED strips and the controller before performing any wiring or installation.
• Driftsmiljø: The working temperature range is -20°C to 45°C. Avoid exposing the device to extreme temperatures or high humidity.
• Kun indendørs brug: Denne enhed er beregnet til indendørs brug.

3. Pakkens indhold

Markér venligst feltet for følgende elementer:

• DOMRAEM ESP32 WLED Controller main unit ×1
• Double-sided tape ×1
• Brugervejledning ×1

Note: The WLED Remote Control is sold separately and is not included in the standard package.

4. Specifikationer

5. Opsætningsvejledning

5.1 Wiring the Controller

Before wiring, ensure the power supply is disconnected. The controller uses quick connect ports for convenient wiring.

1. Forbered ledninger: Strip approximately 8-10mm of insulation from the ends of your LED strip wires and power supply wires.
2. Tilslut strømforsyning: Connect your DC 12-24V power supply to the 'INPUT DC12-24V' terminals. Ensure correct polarity (V+ to V+, V- to V-).
3. Connect LED Strip: Connect your PWM LED strip to the 'OUTPUT PWM' terminals. The controller supports various types of strips. Refer to the wiring diagram below for specific connections based on your LED strip type (RGBCCT, RGBW, RGB, CCT, or Dimmer/White).
4. Optional PUSH Button: For DIY use, you can connect a push switch to the 'IO33 GND' terminals. Refer to section 6.3 for button functions.

5.2 Using the Quick Connect Port

The quick connect port design makes wiring simple and secure:

1. Open the connector: Gently pull the lever upwards to open the wire entry.
2. Indsæt ledningen: Insert the stripped end of the wire into the appropriate terminal.
3. Secure the wire: Press the lever down firmly to secure the wire in place. Ensure the wire is properly seated and cannot be easily pulled out.

5.3 Application Download Methods

The WLED application is free to download and available on both Google Play Store and Apple App Store. No gateway is required for operation.

1. Til iOS: Søg efter "WLED" or "WLED Native" in the Apple App Store.
2. Til Android: Søg efter "WLED Native" in the Google Play Store, or download from the web: https://github.com/Aircoookie/WLED-App/releases

5.4 APP Configuration Steps

Follow these steps to configure the WLED app and connect to your controller:

1. Tænd for WLED-controlleren.
2. Open your phone's WiFi settings and connect to the network named "WLED-AP" with the password "wled1234".
3. Åbn a web browser og naviger til 4.3.2.1 to enter the WLED page.
4. Click on "WIFI SETTINGS" to configure your home WiFi network.
5. After successful connection, the controller will automatically redirect to the WLED page.
6. Enter your home WiFi password and click "Save" at the top of the screen. Be sure to choose a 2.4GHz WiFi network, otherwise it will not work.
7. Connect your phone and WLED controller to the same WiFi network.
8. Open the WLED app to begin controlling your lights.

6. Betjeningsvejledning

6.1 WLED-appstyring

Once connected, the WLED app provides comprehensive control over your LED strips:

• Farvejustering: Use the color wheel to select from 16 million colors.
• Lysstyrke/mætning: Adjust the intensity and vibrancy of your lights.
• Forudindstillede tilstande: Choose from multiple user preset modes for various lighting effects.
• Synkroniseringseffekter: Synchronize lighting effects across multiple WLED controllers on the same WiFi network.

6.2 WLED Remote Control (Optional)

If you have purchased the optional WLED remote control, you can use it for convenient operation. The remote offers long-range transmission, robust interference resistance, and low power consumption.

• TIL/FRA: Tænd eller sluk lysene.
• Justering af lysstyrke: Øg eller reducer lysintensiteten.
• Valg af tilstand: Cycle through different lighting modes or presets.

6.3 Controller Button Functions (Restart & Opt)

The controller features two physical buttons: Restart and Opt.

• Genstart knap: Pressing this button briefly will power off the controller module (temporarily disabling WLED functionality). Release the button to restore power and resume normal operation. This feature allows quick manual power cycling when needed.
• Opt-knap:
  • Kort tryk: Tænd / sluk.
  • 1-Second Long Press: Cycle through lighting colors.
  • 10-Second Long Press: Reset the WLED controller to factory settings and activate the WLED-AP hotspot for initial setup or re-configuration.

6.4 GPIO33 Interface for DIY Use

The IO33 interface is designed for advanced DIY users and can be connected to external push switches, sensors, and more. It provides additional control options:

• Button 0 (Pushbutton):
  • Short press: Power On/Off
  • Short press 1 second: Change color
  • Long press 10 seconds: Enter into WiFi-AP mode, hotspot "WLED-AP" will pop-up
• Button 0 (Switch): Til/Fra
• Button 1 (Pushbutton):
  • Short press: Change lighting modes
  • Double-tap: Change color of the current mode
  • Long press: Dim brightness
• Button 1 (Switch): Til/Fra

6.5 Five Mode Switching

The WLED app allows you to configure the controller for different types of LED strips, ensuring super compatibility. You can switch between RGBCCT, RGBW, RGB, CCT, and White modes within the app's hardware setup.

7. Kompatibilitet

7.1 Compatible Light Strips

The DOMRAEM ESP32 WLED Controller is compatible with the following PWM dimming LED strip types:

• RGBCCT LED Strips
• RGBW LED Strips
• RGB LED Strips
• CCT (Dual White) LED Strips
• Monochrome (Single Color) LED Strips

Important: This controller does NOT support digital addressable LED strips (e.g., WS2812B, SK6812).

7.2 Functional Limitations

• The controller supports global uniform color adjustment. It does not support segment-specific control or chasing-effekter.
• For multi-segment light strips requiring individual control, additional controllers would be necessary.

8. Vedligeholdelse

• Rensning: Use a soft, dry cloth to clean the controller. Do not use harsh chemicals or abrasive cleaners.
• Miljø: Keep the controller in a dry environment, away from direct sunlight, high temperatures, and humidity.
• Power Cycle: If the device becomes unresponsive, perform a brief power cycle using the Restart button or by disconnecting and reconnecting the power supply.
• Firmwareopdateringer: Periodically check for WLED firmware updates to ensure optimal performance and access to new features. The upgradeable version (DOM-WLE-ACLE) supports firmware burning via its Type-C port.

9. Fejlfinding

• LED-striben lyser ikke:
  • Check power supply connection and ensure it's within 12-24V.
  • Verify LED strip wiring polarity and connections.
  • Confirm the LED strip is a compatible PWM type, not digital addressable.
  • Check if the controller is powered on (LED indicator should be active).
• Cannot Connect to WLED-AP WiFi:
  • Sørg for, at controlleren er tændt.
  • Try a 10-second long press on the 'Opt' button to reset to factory settings and re-activate the WLED-AP hotspot.
  • Make sure your phone is close to the controller.
• Cannot Connect to Home WiFi:
  • Ensure your home WiFi is 2.4GHz. The controller does not support 5GHz networks.
  • Double-check the WiFi password entered in the WLED settings.
  • Ensure your phone is connected to the same 2.4GHz home WiFi network after configuring the controller.
• Lights are Flickering or Unresponsive:
  • Tjek for løse ledningsforbindelser.
  • Ensure the total current draw does not exceed 20A and individual channel current does not exceed 15A.
  • Perform a power cycle on the controller.
  • If using a remote, ensure batteries are fresh and there are no obstructions.
• WLED App Not Finding Controller:
  • Ensure both your phone and the controller are connected to the same WiFi network.
  • Restart the WLED app.
  • Genstart controlleren.

10. Brugertips

• For optimal performance, ensure your WiFi network is stable and provides good coverage to the controller's location.
• Consider using the Type-C programming interface on the upgradeable version (DOM-WLE-ACLE) for advanced customization or if you need to flash specific WLED firmware versions.
• If integrating with Home Assistant, ensure your Home Assistant instance is properly configured for WLED devices.

11. Garanti og support

This product comes with a 2-year warranty. For technical support, troubleshooting assistance, or warranty claims, please contact DOMRAEM Official Store customer service. Online technical support is available to assist you with any issues.

12. Ofte stillede spørgsmål (FAQ)

Q: Does this controller work with addressable LED strips like WS2812B?

A: No, this controller is specifically designed for PWM dimming LED strips and is not compatible with digital addressable LED strips.

Q: Can I control multiple segments of an LED strip independently?

A: This controller supports global uniform color adjustment. It does not support segment-specific control or chasing effects. For multi-segment control, you would need additional controllers.

Q: Is a remote control included?

A: The WLED Remote Control is sold separately and is not included in the standard package.

Q: What should I do if I forget my WLED-AP password?

A: The default password for WLED-AP is "wled1234". If you've changed it and forgotten, you can perform a 10-second long press on the 'Opt' button to reset the controller to factory settings, which will restore the default WLED-AP hotspot.