1. Introduktion
The VBESTLIFE High Precision I2S ADC Audio Capture Card Module is a versatile development board designed to convert analog audio signals into high-quality I2S digital signals. This module supports both master and slave operating modes, offering flexibility for various audio processing applications. It features multiple input options and configurable bit depths and sampling rates, making it suitable for a wide range of digital audio projects.
2. Nøglefunktioner
- I2S Signal Conversion: Converts analog audio signals into I2S digital signals.
- Master Mode Support: Configurable for 24-bit 192kHz and 24-bit 96kHz master modes.
- Slave Mode Support: Configurable for 24-bit 192kHz, 24-bit 96kHz, 24-bit 48kHz, and 16-bit 48kHz slave modes.
- Automatic Output: Default host output mode automatically converts audio input to 24-bit 192kHz/96kHz I2S signal upon power-on.
- Flexible Input Options: Supports 3.5mm audio jack or RCA (Red/White) analog inputs.
- Misligholdelse Ampliifikation: Provides a default 6dB amplificeringseffekt.
3. Specifikationer
| Attribut | Værdi |
|---|---|
| Varetype | Audio Capture Card Module |
| Materiale | PCB |
| Mærkenavn | VBESTLIFE |
| Kommunikationsmetode | Bluetooth-Compatible (Note: This attribute may refer to general product category features and not direct module functionality.) |
| Oprindelse | Fastlandet Kina |
| Host Mode Settings | 24-bit 192kHz, 24-bit 96kHz |
| Slave Mode Settings | 24-bit 192kHz, 24-bit 96kHz, 24-bit 48kHz, 16-bit 48kHz |
| Pakkens længde | 14 cm |
| Pakkebredde | 9 cm |
| Pakkehøjde | 3 cm |
| Pakkevægt | 0.032 kg |
4. Pakkens indhold
Tjek venligst pakken for følgende varer:
- 1 x I2S ADC Audio Capture Card Module
- 1 x forbindelseskabel
5. Opsætningsvejledning
The module is designed for manual setup without requiring programming or driver installation. Configuration is primarily done via jumpers on the board.
5.1. Jumper Configuration for Master/Slave Mode and Sampling Rate
Refer to Figure 4 for the location of the jumpers on the underside of the module. These jumpers control the operating mode (Master/Slave) and various sampling frequency settings.
- Master -tilstand: To configure the module as a master, set the appropriate jumpers as indicated on the board for 24-bit 192kHz or 24-bit 96kHz operation. The image shows 'Master 96K = 256fs' and '192K = 128fs'.
- Slavetilstand: To configure the module as a slave, set the jumpers for the desired bit depth and sampling rate (e.g., 24-bit 192kHz, 24-bit 96kHz, 24-bit 48kHz, or 16-bit 48kHz). The image indicates 'Slave Sampling Frequency: 8-192kHz' with various fs options.
- Left/Right Justified (LJ/RJ): The jumpers labeled '1=LJ' and '0=RJ' allow selection of Left Justified or Right Justified I2S format, if applicable to your setup.
5.2. Power and Signal Connections
Connect the module to your system using the provided connection cable and appropriate power supply (VCC=5V). The I2S output pins are clearly labeled on the board:
- VCC: +5V strømforsyning
- GND: Jord
- DGND: Digital jord
- LRCK: Left/Right Clock
- DATA: I2S Data
- BICK: Bit Clock
- MCLK: Master Clock (24.576M)
For analog audio input, use either the 3.5mm jack or the RCA (Red for Right, White for Left) connectors.
6. Betjening
Once the module is correctly configured via jumpers and connected to power and audio sources, it will begin converting analog audio to I2S digital signals according to the selected mode.
- Default Host Output: In its default configuration, the module operates in host output mode, automatically converting the incoming analog audio signal to a 24-bit 192kHz or 96kHz I2S signal for output.
- Analog input: Connect your analog audio source (e.g., a CD player, microphone pre-amp) to either the 3.5mm input jack or the RCA L/R inputs.
- I2S Output: The converted I2S digital audio signal is available on the labeled header pins for connection to a compatible I2S receiver or digital audio processor.
7. Vedligeholdelse
- Opbevar modulet i et tørt og støvfrit miljø.
- Undgå at udsætte modulet for ekstreme temperaturer eller fugt.
- Do not attempt to disassemble the module beyond its intended jumper configurations.
- Clean the board gently with a soft, dry cloth if necessary. Avoid using liquids or harsh chemicals.
8. Fejlfinding
- No I2S Output:
- Verify that the module is receiving proper 5V power.
- Check all jumper settings to ensure they match the desired master/slave mode and samplang hastighed.
- Ensure analog audio input is present and at an appropriate level.
- Confirm all I2S output connections (LRCK, DATA, BICK, MCLK) are correct and secure.
- Forvrænget lyd:
- Check the input analog audio signal for clipping or excessive noise.
- Ensure the receiving I2S device is configured for the correct bit depth and sampling rate output by the module.
- Kontroller strømforsyningens stabilitet.
- Modulet genkendes ikke:
- This module does not require drivers. Ensure your I2S receiving device is correctly configured to accept the I2S stream.
9. Brugertips
Der var ingen specifikke brugertips tilgængelige fra reviews or Q&A for this product at this time. Always ensure proper grounding and power supply to prevent noise in your audio signal.
10. Garanti og support
For warranty information and technical support, please refer to the seller's policies or contact the vendor directly. Keep your purchase receipt for any warranty claims.
