HITBOX TIG200 2-i-1 svejsemaskine brugermanual

1. Introduktion

The HITBOX TIG200 is a versatile 2-in-1 welding machine designed for both MMA (Manual Metal Arc) / ARC and HF (High Frequency) TIG (Tungsten Inert Gas) welding. Featuring advanced IGBT inverter technology, it offers stable performance, high efficiency, and a compact, lightweight design suitable for various applications from DIY projects to professional repair and construction work. This manual provides essential information for safe and effective operation of your welding machine.

Figure 1: HITBOX TIG200 Welding Machine and Included Accessories

2. Sikkerhedsoplysninger

Always prioritize safety when operating welding equipment. Failure to follow safety precautions can result in serious injury or death. Read and understand all safety warnings before use.

• Wear appropriate personal protective equipment (PPE), including a welding helmet with proper shade, flame-resistant clothing, welding gloves, and safety shoes.
• Sørg for tilstrækkelig ventilation for at undgå indånding af svejserøg.
• Hold en ildslukker i nærheden.
• Svejs ikke i nærheden af ​​brændbare materialer.
• Ensure the work area is dry and free from moisture.
• Rør aldrig ved strømførende elektriske dele.
• Afbryd strømmen, før du udfører vedligeholdelse eller udskifter tilbehør.
• Kun kvalificeret personale bør udføre reparationer.

3. Pakkens indhold

Bekræft, at alle nedenstående varer er inkluderet i din pakke:

Figure 2: Included Accessories with the TIG200 Welder

1. TIG200 Welder
2. Elektrodeholder
3. Jord Clamp
4. Gasslange
5. TIG Torch Consumables (collets, collet bodies, ceramic nozzles)
6. WP17 TIG Torch
7. Adapterstik
8. Brush & Hammer
9. Welding Rods (for MMA)

4. Produktet er slutview

4.1. Kontrolpanel og tilslutninger

Familiarize yourself with the front and rear panels of the TIG200 welding machine:

Figure 3: TIG200 Panel Introduction

• Frontpanel:
1. Current Display: Shows welding current.
2. Power Indicator: Illuminates when the machine is powered on.
3. Abnormal Indicator (O.C): Illuminates in case of overload or overheating.
4. Welding Mode Button: Toggles between TIG and ARC (MMA) welding modes.
5. Current Adjustment Knob (A): Adjusts the welding current (Amperage).
6. Post Gas Adjustment Knob (S): Adjusts the post-flow gas time (1-10 seconds) for TIG welding.
7. Positive Terminal (+): For connecting the electrode holder (MMA) or ground clamp (TIG).
8. Torch Switch: Connection for the TIG torch trigger cable.
9. TIG Torch Connection: For connecting the TIG torch.
10. Negative Terminal (-): For connecting the ground clamp (MMA) or electrode holder (TIG).
• Bagside:
1. Power Switch: Main power on/off switch.
2. Gas In: Connection for the inert gas supply (e.g., Argon) for TIG welding.

4.2. Nøglefunktioner

Figure 4: Multiple Advantages of the TIG200

• Dual Voltage: Supports both 110V and 220V input.
• Good Heat Dissipation: Efficient cooling system for extended operation.
• Hot Start: Provides an initial boost of current to prevent the electrode from sticking.
• Arc Force: Helps maintain a stable arc and prevents sticking, especially with longer arc lengths.
• Anti-stick: Reduces the current if the electrode sticks, making it easier to detach.
• Latest IGBT Technology: Sikrer stabil lysbue, mindre sprøjt og høj effektivitet.
• Overstrømsbeskyttelse: Safeguards the machine from excessive current.
• Høj arbejdscyklus: Allows for longer welding periods without overheating.
• Post Gas Function: Variable air post time (1-10 seconds) from the torch helps cool the torch and consumables, enhancing their durability.

5. Opsætning

Before operating the machine, ensure proper connections for your chosen welding mode.

5.1. MMA/ARC Welding Setup

1. Ensure the machine's power switch (A) is OFF.
2. Connect the Electrode Holder cable to the Positive Terminal (+) on the front panel.
3. Tilslut jord Clamp cable to the Negative Terminal (-) on the front panel.
4. Fastgør jorden clamp securely to the workpiece or welding table.
5. Insert a suitable welding electrode into the electrode holder.
6. Switch the welding mode button (4) to 'ARC'.
7. Connect the machine to the appropriate power supply (110V or 220V).
8. Turn on the machine's power switch (A).

5.2. HF TIG Welding Setup

1. Ensure the machine's power switch (A) is OFF.
2. Connect the TIG Torch cable to the TIG Torch Connection (9) on the front panel.
3. Connect the TIG Torch trigger cable to the Torch Switch (8) connection.
4. Tilslut jord Clamp cable to the Positive Terminal (+) on the front panel.
5. Fastgør jorden clamp securely to the workpiece or welding table.
6. Connect the gas hose (4) from your inert gas cylinder (e.g., Argon) to the 'Gas In' (B) connection on the rear panel. Ensure the gas cylinder valve is closed before connecting.
7. Install the appropriate tungsten electrode and consumables (collet, collet body, ceramic nozzle) into the TIG torch.
8. Switch the welding mode button (4) to 'TIG'.
9. Connect the machine to the appropriate power supply (110V or 220V).
10. Turn on the machine's power switch (A).
11. Open the gas cylinder valve and set the desired gas flow rate on the regulator.

6. Betjeningsvejledning

6.1. MMA/ARC Welding Operation

1. After completing the MMA setup (Section 5.1), turn on the machine.
2. Select 'ARC' mode using the welding mode button (4).
3. Adjust the welding current using the Current Adjustment Knob (A) according to the electrode type and material thickness. The current display (1) will show the set value.
4. Begin welding, maintaining a consistent arc length and travel speed.
5. After welding, use the brush and hammer (8) to remove slag.

6.2. HF TIG Welding Operation

1. After completing the TIG setup (Section 5.2), turn on the machine and open the gas valve.
2. Select 'TIG' mode using the welding mode button (4).
3. Adjust the welding current using the Current Adjustment Knob (A) based on the material type and thickness.
4. Set the Post Gas time using the Post Gas Adjustment Knob (S). A post-flow time of 5-10 seconds is generally recommended to protect the weld puddle and tungsten from atmospheric contamination as it cools.
5. Initiate the arc by pressing the TIG torch trigger. The High Frequency (HF) start will create a non-contact arc, preventing tungsten contamination.
6. Oprethold en ensartet buelængde, og før svejsetråden (hvis brugt) ned i svejsebadet.
7. Release the trigger to stop welding. The post-flow gas will continue for the set duration.

6.3. Svejseapplikationer

The TIG200 is suitable for welding various materials, including:

• Blødt stål
• Rustfrit stål
• Stålplade
• Firkantet rør
• Kulstofstål
• Kobber

Figure 5: Wide Range of Weldable Materials

7. Vedligeholdelse

Regelmæssig vedligeholdelse sikrer din svejsemaskines levetid og optimale ydeevne.

• Rensning: Periodically clean the machine's exterior with a dry cloth. Use compressed air to blow out dust and debris from the ventilation openings.
• Forbindelser: Regularly check all cable connections for tightness and signs of wear or damage. Replace damaged cables immediately.
• TIG-brænder: Inspect the TIG torch consumables (tungsten, collet, collet body, ceramic nozzle) for wear and replace as needed. Ensure the tungsten is properly sharpened.
• Jord Clamp: Keep the ground clamp clean and ensure it makes good electrical contact with the workpiece.
• Opbevaring: Opbevar maskinen i et tørt, støvfrit miljø, når den ikke er i brug.

8. Fejlfinding

Dette afsnit omhandler almindelige problemer, du kan støde på. Kontakt kundesupport, hvis du har problemer, der ikke er nævnt her.

9. Specifikationer

10. Brugertips

• Øvelse gør mester: If you are new to welding, start with scrap pieces of metal to get a feel for the machine and different settings.
• Renlighed er nøglen: Always ensure your workpiece is clean and free of rust, paint, or oil for the best weld quality, especially with TIG welding.
• Gas Flow for TIG: Proper inert gas flow is crucial for TIG welding. Too little gas can lead to porosity, while too much can cause turbulence and draw in atmospheric contaminants.
• Valg af elektrode: Choose the correct electrode type and diameter for your material and desired current in MMA welding.
• Tungsten forberedelse: For TIG welding, ensure your tungsten electrode is properly ground to a sharp point for precise arc control.

11. Garanti og support

For garantioplysninger, teknisk support eller serviceforespørgsler bedes du kontakte din forhandler eller producenten direkte. Gem din købskvittering som købsbevis.