1. Introduktion
This manual provides essential information for the safe and efficient operation of your EASUN POWER ICharger-MPPT-48V-60A-E-1 Solar Charge Controller. Please read this manual thoroughly before installation and use. Keep this manual for future reference.
The EASUN POWER MPPT Solar Charge Controller is designed to optimize power harvesting from your solar panels and efficiently charge your battery bank. Featuring Maximum Power Point Tracking (MPPT) technology, it ensures high efficiency and performance for 12V, 24V, 36V, and 48V auto-recognized battery systems.
2. Nøglefunktioner
- 60A MPPT solar charge controller with fan cooling.
- MPPT efficiency > 99%, Peak conversion efficiency > 98%.
- DSP processors technology for high speed and performance.
- Multi-stage-opladningstilstand for optimal batterilevetid.
- Omfattende beskyttelsesfunktioner: Kortslutning af PV-panel, omvendt polaritet i PV, omvendt polaritet i batteri, overopladning, kortslutning i udgang.
- Udligningsopladningsfunktion.
- Automatisk system voltage recognition (12V/24V/36V/48V).
- Maksimal PV input voltage: 150VDC.
- Beskyttelsesklasse: IP30.
- Certificeret med CE-, FCC- og RoHS-standarder.
3. Sikkerhedsoplysninger
Overhold venligst følgende sikkerhedsforanstaltninger under installation og drift:
- Sørg for, at alle forbindelser er sikre og korrekte, før du tænder for systemet.
- Always connect the battery first, then the solar panels, and finally the load. Disconnect in reverse order.
- Do not exceed the maximum PV input voltage på 150VDC.
- Ensure proper ventilation around the controller, especially for fan cooling models.
- Avoid short-circuiting the PV array, battery, or load terminals.
- Brug passende personlige værnemidler (PPE) under installationen.
- This device is not a smart device and does not feature remote monitoring or control.
4. Produktet er slutview
Dimensioner: 285mm (Length) * 217mm (Width) * 125mm (Height)
5. Installation og ledningsføring
Follow these steps carefully to ensure correct and safe installation.
- Tilslut batterier: Connect the battery cables to the battery positive and negative ports on the charge controller. Ensure correct polarity.
- Tilslut belastningen: Connect the DC load to the positive and negative terminals of the DC load on the charge controller.
- Tilslut solpaneler: Connect the solar panel cables to the PV input interface on the charge controller. Ensure correct polarity and that the PV array voltage ikke overstiger 150VDC.
- Connect Inverter (Optional): If using an inverter, connect it to the battery terminals (not directly to the load terminals of the controller).
Important: Always connect the battery first, then the solar panels, and finally the load. Disconnect in the reverse order: load, then solar panels, then battery.
Video 1: Installation Demonstration - Shows the physical connection process for the charge controller.
6. Betjeningsvejledning
6.1. Knapfunktioner
| Knap | Knapmønster | Knap funktion |
|---|---|---|
| MENU | ▲ (Up arrow) | Short press to switch down. Press and hold for 3 seconds to enter the next interface. |
| SÆT | ▼ (Down arrow) | Short press to switch up. Press and hold for 3 seconds to exit without saving. |
6.2. Boot Screen
When the controller is powered on, the LCD screen will display the following sequence:
- Starting interface (normal to detect LCD when system is powered on).
- Batteri voltage interface.
- Softwarerevision.
Notice: At the first interface, long press "MENU" button to enter the secondary interface. It will automatically switch to the first interface without doing anything for 15 seconds.
6.3. LCD Screen Status Introduction
| Punkt | ICO | Status |
|---|---|---|
| PV-array | Sun icon / Moon icon | Dag nat |
| Sun icon -> MPPT -> Battery icon | Opladning | |
| Batteri | Batteri ikon | Uopladet / Batterikapacitet |
| LiPo / LiFe icons | Batteritype | |
| Indlæs | Lightbulb icon (on) / Lightbulb icon (off) | Læss på / Læss af |
6.4. Main Loop Pages
After the controller is powered on, the LCD screen will enter the main page. Short press "MENU" or "SET" to switch among the main loop pages:
- Hovedside
- Batteritemperatur
- Ladestrøm
- Afladestrøm
- Accumulated Charging AH
- Accumulated Discharging AH
6.5. Load Switch On/Off
From the main page, short press the "SET" button to switch the load on/off.
6.6. Systemindstillinger
Under the main page, long press "MENU" for 3 seconds to enter the setting page. Then short press "MENU" or "SET" to switch among the setting pages. Long press "MENU" for 3 seconds to save settings, or long press "SET" for 3 seconds to exit without saving.
6.6.1. System Voltage Indstilling
Når du har åbnet indstillingssiderne, skal du skifte til systemvolumen.tage page. Long press "MENU" for 3 seconds until the "Auto" starts to flash. Then short press "MENU" or "SET" to turn the system voltage to 12V or 24V (or 36V/48V as per auto-recognition capability).
6.6.2. Indstilling af batteritype
Under the main page, long press "MENU" for 3 seconds to enter the setting page, and then short press "MENU" to switch to the battery type page (user mode 1).
After entering the battery type page (user mode 1), long press "MENU" for 3 seconds to enter battery type selection pages. Short press "MENU" or "SET" to switch among Gel battery, Sealed battery, Flooded battery, and Lithium batteries.
Under each lithium battery page, long press "MENU" for 3 seconds to enter a program of setting lithium battery's capacity. At this time, the parameters on the screen will start flashing. Keep long pressing "MENU" for 3 seconds, the parameter will become to battery capacity. Short press "MENU" or "SET" to set the capacity of the currently connected lithium batteries. After setting the parameters, save the data. Long press "MENU" for 3 seconds to save.
7. Vedligeholdelse
- Kontrollér regelmæssigt alle ledningsforbindelser for tæthed og korrosion.
- Ensure the controller's cooling fan and vents are free from dust and debris to maintain optimal cooling.
- Kontroller batteripolerne regelmæssigt for korrosion, og rengør dem om nødvendigt.
- Verify that the solar panels are clean and free from obstructions.
- Check the LCD display for any error messages or unusual readings.
8. Fejlfinding
Hvis du støder på problemer, kan du se følgende almindelige fejlfindingstrin:
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Ingen visning på LCD | Ingen strøm fra batteriet eller forkert batteritilslutning. | Tjek batterivolumentage and ensure battery cables are correctly connected to the controller. |
| Batteriet oplades ikke | Solar panels not connected, insufficient sunlight, PV reverse polarity, or PV array short circuit. | Check solar panel connections and polarity. Ensure adequate sunlight. Inspect PV array for damage. |
| Indlæsningen virker ikke | Load switch off, load short circuit, or battery voltage for lavt. | Turn on the load switch. Check load wiring for short circuits. Ensure battery is sufficiently charged. |
| Overcharging indication | Incorrect battery type setting or faulty battery. | Verify battery type settings. Test battery health. |
9. Specifikationer
| Parameter | Værdi |
|---|---|
| Mærkenavn | EASUN POWER |
| Modelnummer | ICharger-MPPT-48V-60A-E-1 |
| Maksimal strøm | 60A |
| System Nominel Voltage | 12V/24V/36V/48V Auto |
| Max PV-indgang Voltage | 150VDC |
| Udladningssløjfevolumentage Drop | ≤0.2V |
| Beskyttelsesklasse | IP30 |
| MPPT effektivitet | >99 % |
| Maksimal konverteringseffektivitet | >98 % |
| Dimensioner (L*B*H) | 285mm * 217mm * 125mm |
| Er en smart enhed | Ingen |
| Certificeringer | CE, FCC, RoHS |
| Oprindelse | Fastlandet Kina |
10. Brugertips
- Solar Panel Configuration: When connecting multiple solar panels, ensure their series and parallel configurations respect the controller's maximum PV input voltage (150VDC) and current (60A). For example, if using 610W panels, connecting two in series and then multiple such strings in parallel is a common approach, but always verify the total voltage and current remain within the controller's limits.
- Voltage Auto-Recognition: The controller automatically detects 12V, 24V, 36V, or 48V battery systems. Ensure your battery bank matches one of these standard voltagfor korrekt drift.
- Valg af batteritype: Accurately setting the battery type (Gel, Sealed, Flooded, Lithium) in the controller's settings is crucial for optimal charging and battery longevity. For lithium batteries, remember to also set the correct capacity.
11. Garanti og support
For garantioplysninger, teknisk support eller serviceforespørgsler bedes du kontakte din forhandler eller producenten direkte. Gem din købskvittering som købsbevis.
