Indledning
The Aigo AC SE 120 is a high-performance all-in-one (AIO) liquid CPU cooler designed to provide efficient cooling for your processor while adding a vibrant aesthetic to your PC build with its Rainbow (RGB) lighting. This manual provides detailed instructions for installation, operation, maintenance, and troubleshooting to ensure optimal performance and longevity of your cooler.
Specifikationer
Refer to the table below for detailed technical specifications of the Aigo AC SE 120 Liquid CPU Cooler.
| Attribut | Værdi |
|---|---|
| Type | Flydende CPU-køler |
| Modelnummer | ACSE120-WH |
| Mærke | Aigo |
| Kompatible stikkontakter | Intel: LGA 2066/2011-V3/2011/1700/1366/1200/115X - AMD: FM1/FM2/FM2+/AM2/AM2+/AM3/AM3+/AM4 |
| Vandblokstørrelse | 71x66.5x45 mm |
| Rørlængde | 330 mm |
| Pumpehastighed | 3200 ± 10 % RPM |
| Pumpe voltage | 12V |
| Pump Bearing | Keramisk |
| Radiatorstørrelse | 154x120x27 mm |
| Fan størrelse | 120x120x25 mm |
| Blæserhastighed | 800 ~ 1800 ± 10% RPM |
| Fan Rated Voltage | 12V |
| Ventilator luftstrøm | 64.05 CFM |
| Støjniveau for ventilator | 30 dBA ± 10% |
| Static Fan Pressure | 1.85 mmH2O |
Pakkens indhold
Kontroller venligst, at alle følgende komponenter er inkluderet i din pakke:
- Aigo AC SE 120 Liquid CPU Cooler (Radiator, Pump/Water Block, Tubes, Pre-filled coolant)
- 120mm Rainbow (RGB) Fan
- Mounting hardware for Intel sockets (LGA 2066/2011-V3/2011/1700/1366/1200/115X)
- Mounting hardware for AMD sockets (FM1/FM2/FM2+/AM2/AM2+/AM3/AM3+/AM4)
- Termisk pasta
- Fan and RGB connection cables
- Brugermanual
Installationsvejledning
Before beginning installation, ensure your system is powered off and unplugged. Refer to your motherboard manual for specific CPU socket mounting instructions if needed.
1. Forbered CPU'en og bundkortet
- Unpack all components and ensure you have the correct mounting hardware for your CPU socket (Intel or AMD).
- Rengør CPU-overfladen med isopropylalkohol for at fjerne gammel termisk pasta eller rester.
- Installer den relevante bagplade (hvis det er nødvendigt til din sokkel) på bagsiden af bundkortet.
2. Påfør termisk pasta
Apply a small amount of thermal paste (included) to the center of your CPU's integrated heat spreader (IHS). A pea-sized dot is usually sufficient. The pressure from the water block will spread it evenly.
3. Mount the Water Block
- Attach the correct mounting brackets to the water block/pump unit.
- Carefully align the water block with the CPU and the mounting holes on the motherboard.
- Gently place the water block onto the CPU, ensuring even contact.
- Secure the water block using the provided screws, tightening them in a diagonal pattern until snug. Do not overtighten.
4. Mount the Fan to the Radiator
- Using the longer screws, attach the 120mm fan to the radiator. Ensure the fan is oriented to push or pull air in the desired direction for your case's airflow.
5. Mount the Radiator to the PC Case
- Identify a suitable mounting location in your PC case for a 120mm radiator (e.g., rear exhaust, top, or front intake).
- Secure the radiator to the case using the shorter screws provided.
6. Tilslut kabler
- Connect the pump's 3-pin or 4-pin power cable to the designated CPU_FAN or AIO_PUMP header on your motherboard.
- Connect the fan's 4-pin PWM cable to a CPU_FAN or SYS_FAN header on your motherboard.
- Connect the RGB cable from the fan and pump to an available 3-pin 5V Addressable RGB (ARGB) header on your motherboard or an RGB controller (if included/used).
Betjeningsvejledning
Once installed, the Aigo AC SE 120 operates automatically. The pump and fan speeds are typically controlled by your motherboard's BIOS/UEFI settings or dedicated software, based on CPU temperature.
- Første gang tændt: After installation, power on your PC. Check for any unusual noises or leaks. The pump should run quietly, and the fan should spin.
- BIOS/UEFI-indstillinger: Access your motherboard's BIOS/UEFI to ensure the CPU fan header is set to PWM mode (if applicable) and that fan curves are configured for optimal cooling and noise levels.
- RGB kontrol: If connected to an ARGB header, you can control the lighting effects using your motherboard's RGB software (e.g., ASUS Aura Sync, MSI Mystic Light, Gigabyte RGB Fusion, ASRock Polychrome Sync) or a dedicated RGB controller.
- Temperaturovervågning: Use monitoring software (e.g., HWMonitor, Core Temp) to verify CPU temperatures are within safe operating limits during idle and load conditions.
Opretholdelse
Regelmæssig vedligeholdelse er med til at sikre din flydende CPU-kølers lange levetid og optimale ydeevne.
- Støvrensning: Rengør kølerribberne og ventilatorbladene med jævne mellemrum for at forhindre støvophobning, som kan hæmme luftstrømmen og reducere køleeffektiviteten. Brug trykluft eller en blød børste.
- Kabelstyring: Sørg for, at alle kabler er korrekt ført og ikke kommer i vejen for ventilatorblade eller andre komponenter.
- Tjek for lækager: Although rare, regularly inspect the tubes and connections for any signs of coolant leakage. If a leak is detected, power off your system immediately and contact support.
- Pumpestøj: Listen for any unusual pump noises. A gurgling sound might indicate air bubbles, which usually resolve themselves over time. Persistent loud noises could indicate an issue.
Fejlfinding
Her er nogle almindelige problemer og deres potentielle løsninger:
- Høje CPU-temperaturer:
- Ensure the water block is securely mounted and making good contact with the CPU.
- Bekræft påføring af termopasta.
- Check that the pump and fan are receiving power and spinning correctly.
- Clean any dust from the radiator fins.
- Sørg for korrekt luftgennemstrømning i dit pc-kabinet.
- Pump Not Running/Making Noise:
- Check the pump's power connection to the motherboard.
- Ensure the correct header (CPU_FAN or AIO_PUMP) is used and configured in BIOS.
- A slight gurgling sound initially is normal as air bubbles settle. If persistent and loud, try gently tilting your PC case to help dislodge air bubbles.
- Fan Not Spinning/RGB Not Working:
- Verify all fan and RGB cables are securely connected to the motherboard or controller.
- Check your motherboard's BIOS/UEFI settings for fan control.
- Sørg for, at dit bundkorts RGB-software er installeret og konfigureret korrekt.
- Cooler Leaking:
- Immediately power off your system and unplug it.
- Do not attempt to repair. Contact customer support for assistance.
Brugertips
To get the most out of your Aigo AC SE 120 Liquid CPU Cooler:
- Optimer luftstrømmen: Ensure your PC case has good overall airflow to help dissipate heat from the radiator effectively.
- Overvåg temperaturer: Regularly monitor your CPU temperatures, especially during demanding tasks, to ensure stable performance.
- Kabelstyring: Good cable management not only improves aesthetics but also enhances airflow within your case.
- Software kontrol: Utilize your motherboard's fan control and RGB software to customize performance and lighting to your preference.
Garanti og support
The Aigo AC SE 120 Liquid CPU Cooler comes with a 12 måneders garanti fra købsdatoen. Denne garanti dækker fabrikationsfejl og funktionsfejl ved normal brug. Gem venligst din købsbevis til garantikrav.
For technical support, warranty claims, or further assistance, please contact the seller or the manufacturer's official support channels. Refer to the contact information provided by your retailer or on the official Aigo webwebsted.
