Godox MF-R76 TTL Makro Ringlampe Brugermanual

1. Introduktion

The Godox MF-R76 TTL Macro Ring Light is a versatile and powerful lighting solution designed for macro photography. It features TTL auto-flash, manual control, 2.4G wireless system, and dual focus assist lamps, providing precise and shadow-less illumination for capturing intricate details. This manual will guide you through the setup, operation, and maintenance of your MF-R76.

2. Hvad er der i æsken

Billede: Pakkens indhold

• Macro Ring Flash × 1
• USB Charger × 1
• Adapter Rings × 8 (49mm, 52mm, 55mm, 58mm, 62mm, 67mm, 72mm, 77mm)
• Opbevaringspose × 1
• Lithium Battery (7.2V/3000mAh) × 1
• Type-C USB Charging Cable × 1

3. Opsætningsvejledning

3.1 Batteriinstallation

1. Insert the lithium battery into the battery compartment until it clicks into place.

3.2 Montering på kamera

2. Slide the controller onto the camera's hot shoe.
3. Ensure it is fully inserted into the camera's hot shoe socket.
4. Rotate the locking ring to tighten and secure the controller.

3.3 Attaching Ring Flash to Lens

5. Select the appropriate lens adapter ring (e.g., 67mm) for your camera lens.
6. Rotate clockwise to install the adapter ring onto the camera lens.
7. Align the ring flash with the adapter ring interface and gently snap it into place.

4. Betjeningsvejledning

4.1 Generelle kontroller

• MODE knap: Short press to switch between flash modes (ETTL, M).
• SET -knap: Short press to confirm selections or switch between parameters.
• Urskive: Rotate to adjust values or navigate menu options.
• Fokus Assist Lamp Knap: Short press to turn on/off focus assist lamps. Long press to enter adjustment interface.
• MENU knap: Short press to enter/exit the menu. Long press with Focus Assist Lamp button for reset.
• Lock Button (integrated with MENU): Long press to lock/unlock the current interface.

4.2 ETTL Flash Mode

1. Short press the MODE button to switch to ETTL mode.
2. Setting Overall Flash Exposure Compensation:
   a. Short press the 'Ratio' button. The screen will display 'ETTL' and '+/- Exposure Compensation Value'.
   b. Rotate the adjustment dial to set the exposure compensation value (can be set between ±3 stops in 1/3 stop increments).
3. Setting A:B Flash Ratio:
   a. Short press the 'Ratio' button. The screen will display 'A:B' and ratio options (e.g., 8:1, 4:1, 2:1, 1:1, etc.).
   b. Rotate the adjustment dial to set the corresponding ratio value.
   c. Short press the 'SET' button to select between exposure compensation value or A:B flash ratio value.
4. Setting Single-Side Flash (Group A or Group B):
   a. Short press the 'Ratio' button to display 'A B' and exposure compensation value.
   b. Short press the 'SET' button to select flash tube A or B for single-side flash.

4.3 Manual (M) Flash Mode

1. Short press the MODE button to switch to M (Manual) Flash Mode.
2. Setting Overall Flash Power:
   a. The screen will display 'M' and output power (e.g., 1/128).
   b. Rotate the adjustment dial to set the output power.
3. Setting A:B Flash Power:
   a. Short press the 'Ratio' button. The screen will display 'AB' and two output powers (e.g., A: 1/4, B: 1/128).
   b. Rotate the adjustment dial to set the power for each group.
   c. Short press the 'SET' button to select Group A or Group B power. (If Group A outputs flash, Group B can be set to off).

4.4 Trådløse indstillinger

1. Tryk kort på MENU-knappen for at komme ind i menuen.
2. Setting Flash as Master Light (TX):
   a. Rotate the adjustment dial to select 'WIRELESS'.
   b. Short press SET to enter. Rotate dial to select 'TX'.
   c. Press the SET button to return to the previous level.
   d. Short press the MENU button to return to the master light interface.
3. Setting Flash as Slave Light (RX):
   a. Rotate the adjustment dial to select 'WIRELESS'.
   b. Short press SET to enter. Rotate dial to select 'RX'.
   c. Short press the MENU button to return to the slave light interface settings.
   d. Short press the SET button or rotate the dial to switch between Group A/B/C/D. For example, switch to D to set this light as slave light D.
4. Setting Wireless Channel (CH):
   a. In the menu, rotate the adjustment dial to 'CH'.
   b. Short press the SET button to enter the setting interface.
   c. Rotate the adjustment dial to select a channel from 01-32.
5. Setting Wireless ID (ID):
   a. In the menu, rotate the adjustment dial to 'ID'.
   b. Short press the SET button to enter the setting interface.
   c. Rotate the dial to select OFF or an ID from 01-99.
6. Setting Master Flash to Flash (TX FLASH):
   a. By default, the master flash is off.
   b. In the menu, rotate the adjustment dial to 'TX FLASH'.
   c. Short press the SET button to enter the interface.
   d. Rotate the dial to select off or on for master flash.

4.5 Højhastighedssynkronisering (HSS)

1. In the menu, rotate the dial to 'SYNC'.
2. Short press the SET button to enter settings.
3. Rotate the adjustment dial and select 'H'.
4. At this time, 'H' will be displayed in the upper right corner of the main screen, indicating HSS is active.

4.6 Synkronisering af forreste/bageste gardin

1. In the menu, rotate the dial to 'SYNC'.
2. Short press the SET button to enter settings.
3. Rotate the adjustment dial to select the front curtain sync icon (a single arrow pointing right) or the rear curtain sync icon (two arrows pointing right).

4.7 Fokushjælp Lamps

Image: Focus Assist Lamps in use

• Tænd/sluk: Short press the focus assist lamp knappen for at tænde lamper tændt eller slukket.
• Juster lysstyrke: Long press the focus assist lamp button to enter the adjustment interface. Rotate the dial to adjust brightness from level 01-10. Long press the button again to exit.

4.8 Låsefunktion

• Long press the MENU/Lock button to lock or unlock the current interface. This prevents accidental changes to settings.

4.9 Nulstil funktion

• Long press both the focus assist lamp button and the MENU button simultaneously.
• Continue holding until 'RESET' appears on the screen.
• Release the buttons. Once 'RESET' disappears, the device has been successfully reset to factory defaults.

5. Nøglefunktioner

• Sync for Stunning Captures: Supports high-speed sync (HSS), front and rear curtain sync for sharp, clear photos even with fast-moving subjects.

Image: Sync for Stunning Captures
• Shadow-less Light: As a ring flash sharing the same optical axis as the lens, the TTL R76 delivers shadow-less light that renders all details and illuminates the subject evenly.


Image: Shadow-less Light

• 2.4G trådløst system: Features 2.4G wireless capability, allowing it to work with Godox 2.4G wireless X system lights for diverse lighting setups.


Image: 2.4G Wireless System

• Auto-adjust Brightness (TTL): TTL mode frees you from time-consuming adjustments, ensuring desired illumination without extensive testing.

Image: Auto-adjust Brightness (TTL)
• Langvarig batterilevetid: Powered by a durable lithium battery (7.2V/3000mAh) for extended shooting sessions.


Image: Long-lasting Battery Life

• Variable Contrast: Twin-tube design allows adjustment of each side to a separate power ratio, adding drama and contrast to images.


Image: Variable Contrast

• Newbie-friendly: User-friendly interface makes macro photography accessible even for beginners.

Image: Newbie-friendly Interface

6. Specifikationer

Image: Technical Specifications

7. Vedligeholdelse

• Rensning: Brug en blød, tør klud til at rengøre blitzenheden. Ved genstridigt snavs, gnid letamp en klud kan bruges, efterfulgt af øjeblikkelig tørring. Undgå barske kemikalier eller slibende materialer.
• Opbevaring: Store the unit in a cool, dry place away from direct sunlight and extreme temperatures. Remove the battery if storing for extended periods.
• Batteripleje: Fully charge the battery before first use. Do not overcharge or completely drain the battery. Recharge regularly even if not in use to maintain battery health.
• Objektivadapterringe: Keep adapter rings clean and free of dust to ensure proper attachment and prevent damage to lens threads.

8. Fejlfinding

• Blitzen går ikke ud:
  - Check battery level and ensure it is properly installed.
  - Verify the flash is securely mounted on the camera's hot shoe.
  - Confirm the flash mode (TTL/M) and power settings are appropriate.
  - If using wireless, ensure channels and IDs match between master and slave units.
• Inkonsekvent eksponering:
  - In TTL mode, check exposure compensation settings.
  - In Manual mode, adjust flash power output.
  - Ensure the subject is within the effective flash range.
• Ring light not turning on:
  - Check battery charge.
  - Ensure the unit is powered on.
• Problemer med trådløs kommunikation:
  - Verify that the master and slave units are set to the same channel and ID.
  - Ensure there are no obstructions between the units.
• Skærmen reagerer ikke:
  - Try locking and unlocking the interface using the lock function.
  - If issues persist, perform a factory reset (see section 4.9).

9. Brugertips

• Eksperimentér med tilstande: While TTL offers convenience, explore Manual mode to gain precise control over lighting for specific creative effects.
• Utilize Focus Assist: The dual focus assist lamps are invaluable in low-light conditions, helping your camera achieve accurate focus before flashing.
• Adapterringe: Always use the correct adapter ring size for your lens to ensure a secure fit and prevent damage.
• Trådløs fleksibilitet: Tag advantage of the 2.4G wireless system to position additional Godox lights for more complex and dynamic macro lighting setups.
• Batteristyring: Carry a spare charged battery for extended shooting sessions, especially when working on location.

10. Garanti og support

This product is covered by the manufacturer's standard warranty. For detailed warranty information, technical support, or service inquiries, please refer to the documentation provided with your purchase or contact the official Godox customer support. Keep your proof of purchase for warranty claims.