Indledning
Tak for købetasing the DumboRC X6 2.4GHz 6CH Radio Transmitter and X6FG Receiver. This system is designed for precise control of various RC models, including cars, boats, and tanks. The X6FG receiver features a built-in gyroscope for enhanced stability. Please read this manual thoroughly before use to ensure proper setup and operation.
Pakkens indhold
- 1 x DumboRC X6 Radio Transmitter
- 1 x DumboRC X6FG Receiver (Built-in Gyro)
- 1 x 3CH Light Control Cable
- 1 x brugermanual
Specifikationer
| Feature | Specifikation |
|---|---|
| Mærke | DumboRC (JMRC HOBBY) |
| Sender model | X6 |
| Modtager model | X6FG (with Built-in Gyro) |
| Materiale | Plastic and metal (Transmitter), Plastic and electronic components (Receiver) |
| Sender størrelse | 160 x 100 x 205 mm |
| Modtager størrelse | 35 x 20 x 13 mm (Antenna length: 106 mm) |
| Sender batteri | 4 x AA (medfølger ikke) |
| Kanaler | 6CH |
| Kompatibilitet | RC Car, Boat, Tank Models (e.g., MJX Hyper Go 16207, 16208, 16209, 16210, 14301, 14302, 14210, 14209) |
| Modulationstilstand | GFSK |
| Spreading Mode | FHSS 67 channel pseudo-random frequency hopping |
| Kontrol afstand | 400-500 meter |
| Sender VoltagRækkevidde | 4.8-12V |
| Senderens arbejdsstrøm | 80-120mA |
| Modtager VoltagRækkevidde | 3.3-10V |
| Receiver Operating Current | 30mA |
| RF strøm | <20dbm |
| Dataopløsning | 4096 levels, 0.5us per level |
| Voltage Alarm | 7.4V | 4.8V |
| Transmissionsfrekvens | 2.4 GHz ISM-bånd (2400MHz~2483.5MHz) |
| Certificering | CE |
Opsætningsvejledning
1. Installation af senderbatteri
- Open the battery compartment cover on the bottom of the X6 Transmitter.
- Sæt 4 AA-batterier (medfølger ikke) i batterirummet, og sørg for at polerne vender korrekt.
- Luk batterirummets dæksel forsvarligt.
2. Modtagertilslutning
Connect the X6FG receiver to your RC model's Electronic Speed Controller (ESC) and other components as shown in the diagram below. Ensure all connections are secure and correctly oriented.
This diagram illustrates how to connect the 6-channel X6FG receiver, which includes a built-in gyroscope, to your RC model's motor and ESC. It also shows the concept of programmable mixes between Channel 1 and Channel 2.
3. Forbindelse af sender og modtager
For at etablere kommunikation mellem sender og modtager:
- Sørg for, at både senderen og modtageren er slukket.
- Connect the binding plug (not included, usually comes with your RC model) to the 'BIND' port on the X6FG receiver.
- Power on the receiver. The receiver's LED should start flashing rapidly, indicating it's in binding mode.
- While holding down the 'BIND' button on the X6 Transmitter (usually located under the cover on the top), power on the transmitter.
- Release the 'BIND' button on the transmitter once its LED starts flashing or indicates binding.
- Modtagerens LED-lampe skal lyse konstant, hvilket indikerer en vellykket binding.
- Power off both the transmitter and receiver. Remove the binding plug from the receiver.
- Power on the transmitter first, then the receiver. The connection should now be established.
4. Light Control Cable Connection
The included 3CH Light Control Cable allows you to control auxiliary lights on your RC model. Connect this cable to an available channel on your X6FG receiver (e.g., CH3) and then connect your RC lights to the cable. The dimensions of the cable are shown below.
This image provides the physical dimensions of the 3-channel light control cable, which measures 120mm in total length, with a 24mm wide and 10mm high connector section.
Betjeningsvejledning
1. Senderstyringer overview
Familiarize yourself with the various controls on your DumboRC X6 Transmitter:
This diagram details the control layout of the DumboRC X6 transmitter. Key controls include CH1 and CH2 trim for steering and throttle, EPA (End Point Adjustment) for both channels, and reverse switches. It also highlights the simulator interface/PPM signal interface and a USB power port (limited to 5V voltage output).
- CH1:EPA for Steering: Adjusts the maximum travel of the steering servo.
- CH1:Sub-trim for Steering: Fine-tunes the neutral position of the steering.
- CH1:Reverse for Steering: Reverses the direction of the steering servo.
- CH2:EPA for Throttle: Adjusts the maximum forward/reverse travel of the throttle.
- CH2:Sub-trim for Throttle: Fine-tunes the neutral position of the throttle.
- CH2:Reverse for Throttle: Reverses the direction of the throttle.
- Simulator interface / PPM signal interface: For connecting to PC simulators or other PPM compatible devices.
- USB -strømport: Limited to 5V voltage output, for charging or powering external devices.
2. Gyro Functionality (X6FG Receiver)
The X6FG receiver has a built-in gyroscope to help stabilize your RC model, especially useful for drift cars or vehicles on uneven terrain. The gyroscope sensitivity can typically be adjusted via a dedicated knob or switch on the transmitter (refer to your transmitter's specific controls for gyro adjustment, if available, or the receiver's instructions for manual adjustment).
3. Light Control Operation
If you have connected lights using the 3CH Light Control Cable, you can typically toggle them on/off or cycle through modes using a designated switch or button on your X6 Transmitter. Refer to the video below for a demonstration of light control.
This video demonstrates the operation of the light control feature using the DumboRC X6 transmitter and a connected RC vehicle. It shows how to turn the lights on and off.
Opretholdelse
- Rensning: Brug en blød, tør klud til at rengøre senderen og modtageren. Undgå at bruge opløsningsmidler eller skrappe kemikalier.
- Opbevaring: Store the unit in a cool, dry place away from direct sunlight and extreme temperatures. Remove batteries from the transmitter if not used for extended periods to prevent leakage.
- Antennepleje: Do not bend or cut the receiver antenna. Ensure it is properly routed and protected within your model.
Fejlfinding
- Ingen strøm: Check if the batteries in the transmitter are correctly installed and fully charged. Ensure the receiver is receiving power from the ESC or an external power source.
- No Connection/Binding Issues: Re-attempt the binding process as described in the Setup Guide. Ensure the transmitter and receiver are within range and there are no strong interference sources nearby.
- Uregelmæssig kontrol: Check all wiring connections between the receiver, servos, and ESC. Ensure the receiver antenna is not damaged or obstructed. If the X6FG receiver's gyro is active, try adjusting its sensitivity.
- Lys virker ikke: Verify the 3CH Light Control Cable is correctly connected to both the receiver and the lights. Check the light power source and ensure the lights themselves are functional.
- Kort kontrolområde: Ensure the transmitter and receiver antennas are unobstructed and properly oriented. Avoid operating in areas with high radio interference.
Brugertips
- Batteristyring: Always use fresh or fully charged AA batteries for the transmitter to ensure consistent performance and avoid unexpected signal loss.
- Rækkeviddetest: Before operating your RC model at full range, perform a short-range test to confirm stable communication between the transmitter and receiver.
- Gyrojustering: Experiment with the gyroscope sensitivity settings on the X6FG receiver to find the optimal balance between stability and responsiveness for your specific model and driving style.
Overholdelse
⚠ ADVARSEL: Dette produkt kan udsætte dig for kemikalier, herunder ftalater (DEHP), som i staten Californien er kendt for at forårsage kræft og fosterskader eller andre reproduktionsskader. For mere information, gå til www.P65Warnings.ca.gov.
