Manualer+

Dooya DM45M 50/12

Dooya DM45M 50/12 Tubular Motor and DC31 Control Kit

Instruktionsmanual

Mærke: Dooya | Model: DM45M 50/12

1. Introduktion

This manual provides detailed instructions for the installation, operation, and maintenance of your Dooya DM45M 50/12 Tubular Motor and DC31 Control Kit. This system is designed for motorized rolling shutter doors and awnings, offering both manual and remote control capabilities. Please read this manual thoroughly before installation and use to ensure safe and efficient operation.

2. Pakkens indhold

Standardpakken indeholder følgende komponenter:

  • DM45M 50/12 Tubular Motor (1 unit)
  • DC31 Control Kit (1 unit), including:
    • DC31 Receiver/Controller (1 unit)
    • DC30 Remote Controls (2 units)
    • Power Plug and Wiring Harness
  • Adjust Rod (1 unit)
  • Mounting Brackets (set)
  • Crown (1 unit)
  • Drive Adapter (1 unit)
  • Fasteners (screws, nuts, rivets)

Note: The specific crown and drive adapter provided will match the tube type selected at purchase (e.g., for 55mm groove tube, 60mm octagonal tube, 80mm round tube, etc.).

Dooya DM45M 50/12 Tubular Motor with DC31 Control Kit and two DC30 remotes
Figure 2.1: Dooya DM45M 50/12 Tubular Motor with DC31 Control Kit and two DC30 remotes.
DC31 Control Kit with power plug and two DC30 remotes
Figure 2.2: DC31 Control Kit components.
Adjust rod for motor limit adjustment
Figure 2.3: Adjust rod.
Bag of screws and nuts for installation
Figure 2.4: Fasteners included.

3. Specifikationer

Technical specifications for the Dooya DM45M 50/12 Tubular Motor:

Attribut Værdi
Modelnummer DM45M 50/12
Voltage 220-240V (220/230V), 50/60Hz
Wattage 205W
Strøm 0.89A
Nominel drejningsmoment 50 Nm
Nominel hastighed 12 r/min
Motorvægt 3.12 kg
Arbejdstid S2 4 min
Isoleringsgrad H
Beskyttelsesgrad IP44
Certificering CE
Manuel kontrol Ja
RF433 Remote Support Ja
Kompatible rørstørrelser 80mm, 114mm (round/groove/octagonal depending on adapter)
Batteri inkluderet Ingen
Product nameplate with detailed specifications for DM45M-50/12 motor
Figure 3.1: Product Nameplate with specifications.

4. Sikkerhedsoplysninger

Overhold venligst følgende sikkerhedsforanstaltninger under installation og drift:

  • Ensure all power is disconnected before performing any installation, maintenance, or repair work.
  • Do not connect two switches to one motor.
  • Do not connect one switch to two motors.
  • Motoren må ikke nedsænkes i vand, og den må ikke udsættes for overdreven fugtighed.
  • Avoid physical impact or hitting the motor.
  • Do not drill into the motor body, especially the motor part itself.
  • When installing the crown, fix it with 5 short rivets. Do not pierce the steel ring inside the crown.
  • Ensure proper wiring to avoid electric shock. Consult a qualified electrician if unsure.
  • Keep children and pets away from the operating area of the shutter/awning.
Diagram showing various safety warnings for motor installation and use
Figure 4.1: General Safety Warnings.
Warning not to penetrate the motor body with an arrow pointing to the prohibited area
Figure 4.2: Do not penetrate the motor body.
Warning against nailing the motor part and showing alignment of wheel centerline
Figure 4.3: Prohibited nailing on motor part.

5. Installation

Follow these steps for proper installation of the tubular motor and control kit.

5.1. Crown and Drive Adapter Selection

The crown and drive adapter must be compatible with your rolling tube's outer diameter and inner structure. We provide standard Dooya adapters for common tube types. If your tube has a unique inner structure, you may need to modify the provided adapters, use 3D printed alternatives, or source them locally. If your old crown and drive adapter are in good condition, reusing them is often the best option.

Diagram showing various compatible tube types including 38mm, 40mm, 45mm, 85mm, 50mm Round, 50mm Grooved, 55mm, 63mm, 70mm
Figure 5.1: Compatible Tube Types.

Examples of Crown and Drive Adapters for different tube types:

5.2. Crown and Drive Adapter Installation

  1. Insert the crown onto the motor shaft.
  2. Insert the drive adapter onto the motor shaft, ensuring it aligns correctly with the crown.
  3. Secure the crown with 5 short rivets. Ensure not to pierce the steel ring inside the crown.
  4. Align the wheel centerline of the motor with the tube.
  5. Install the fixed tail plug into the other end of the tube.
Diagram showing steps for crown and drive adapter installation
Figure 5.2: Crown and Drive Adapter Installation.
Instruction to fix crown with rivets and warning not to pierce steel ring
Figure 5.3: Crown Riveting Instruction.
Diagram showing fixed tail plug installation
Figure 5.4: Fixed Tail Plug Installation.

5.3. Montering af beslag

There are typically two methods for bracket installation:

5.3.1. Bracket Installation A (Side Mount)

  1. Mount the brackets to the wall or frame using appropriate fasteners.
  2. Insert the motor assembly into the brackets.
  3. Secure the motor in place.

5.3.2. Bracket Installation B (Top Mount)

  1. Mount the brackets to the top frame or ceiling.
  2. Insert the motor assembly into the brackets.
  3. Secure the motor in place.
Diagram showing Bracket Installation Method A
Figure 5.5: Bracket Installation A.
Diagram showing Bracket Installation Method B
Figure 5.6: Bracket Installation B.

5.4. Installation af kredsløb

Connect the motor to the power supply and control unit according to the wiring diagrams below. Ensure the voltage matches the product nameplate (230V/50Hz or 120V/60Hz).

5.4.1. Circuit Installation A

Standard wiring for basic control.

5.4.2. Circuit Installation B

Alternative wiring configuration.

5.4.3. Circuit Installation C

Wiring for tubular motor with integrated control.

Wiring diagrams for Circuit Installation A, B, and C
Figure 5.7: Circuit Installation Diagrams (A, B, C).

The DC31 Control Kit includes a wiring harness for easy connection. The motor also supports various matchable control systems like DC41, DC42, DC73, DC74, DC43, DC83, and other control systems such as single manual switches (DC59, DC63, DC25, DC27) and central control (DC80, UPS).

Diagram showing matchable control systems and other control systems for the motor
Figure 5.8: Matchable and Other Control Systems.

6. Betjening

6.1. Remote Control (DC31 Kit)

The DC31 Control Kit comes with two DC30 remote controls. These remotes operate on RF433 frequency. Ensure the remote is paired with the DC31 receiver for operation.

DC31 remote control with buttons for up, down, stop, and lock
Figure 6.1: DC30 Remote Control.

6.2. Limit Setting

The motor's upper and lower travel limits need to be set after installation. Use the special regulator (adjust rod) to set these limits.

6.2.1. Indstilling af opgrænse

  1. Tænd for strømmen.
  2. Press the UP button on the remote control one time.
  3. Use the special regulator to adjust the '+' direction, rotating the red worm when needing to increase the up distance.
  4. When the desired UP limit is achieved, stop rotating the red worm and press the STOP button on the remote. The up limit setting is now complete.

Note: If the motor doesn't stop rotating, check the red or white worm with the regulator.

Instructions for setting the upper limit of the motor's travel
Figure 6.2: Up Limit Setting.

6.2.2. Nedegrænseindstilling

  1. Tænd for strømmen.
  2. Press the DOWN button on the remote control one time.
  3. Use the special regulator to adjust the '+' direction, rotating the red worm when needing to increase the down distance.
  4. When the desired DOWN limit is achieved, stop rotating the red worm and press the STOP button on the remote. The down limit setting is now complete.

Note: If the motor doesn't stop rotating, check the red or white worm with the regulator.

Instructions for setting the lower limit of the motor's travel
Figure 6.3: Down Limit Setting.
Close-up of motor limit adjustment mechanism
Figure 6.4: Motor Limit Adjustment.

6.3. Manual Control (When Power Off)

The DM45M motor supports manual control in case of power failure. A hand crank can be connected to operate the shutter/awning.

Diagram showing manual control operation of a rolling shutter when power is off
Figure 6.5: Manual Control Operation.
Diagram showing various hand crank accessories and how they connect to the motor
Figure 6.6: Hand Crank Accessories.
Close-up of hand crank connector
Figure 6.7: Hand Crank Connector.

7. Vedligeholdelse

The Dooya DM45M tubular motor is designed for low maintenance. However, regular checks can prolong its lifespan and ensure optimal performance:

  • Periodically inspect all mounting hardware to ensure it is secure.
  • Check the power cable for any signs of damage or wear.
  • Keep the motor and control unit free from dust and debris. Use a soft, dry cloth for cleaning.
  • Ensure the shutter or awning mechanism operates smoothly without obstruction.
  • Do not attempt to lubricate internal motor components.

8. Fejlfinding

Se tabellen nedenfor for almindelige problemer og løsninger på disse:

Ingen. Fail-phenomena Fejl forårsager Solutions failure recovery
1 Press the UP button of the controller, the shutter moves downward Inside wire connecting of the controller is wrong Exchange the position of black wire and brown wire
2 Switch on, the drive adapter runs in one-way operation Inside limit switch of motor doesn't open Crown running one circle in the opposite direction, then it works
3 Motor starts slowly or not work after connect power en. Power voltage is slow
b. Ledningsfejl
c. Overbelaste
d. Improper installation		 a. Adjust power to rated data
b. Check circuit and correct wiring connecting
c. Rated torque associated with the installation of the load
d. Re-install the motor
4 Motoren stopper pludseligt efter drift Motoren stopper pludseligt efter drift Motor will automatically resume work after 20 minutes cooling
5 Abnormal sound during roller blinds in operation Outer tube is too long, led the rolling shutter connects with both sides of bracket too tightly If idler is active, properly make the tube shorter to avoid too tight status.
Troubleshooting table for common motor failures and solutions
Figure 8.1: Common Failures and Solutions.

9. Brugertips

  • This motor system is suitable for both rolling shutter doors and awnings.
  • Always double-check the compatibility of the crown and drive adapter with your specific tube type before installation. Modifications or local sourcing might be necessary for non-standard tubes.
  • For optimal performance and longevity, ensure all electrical connections are secure and correctly wired according to the provided diagrams.

10. Garanti og support

For garantioplysninger, teknisk support eller serviceforespørgsler bedes du kontakte din forhandler eller producenten direkte. Gem din købskvittering som købsbevis.

Relaterede dokumenter - DM45M 50/12

Preview DOOYA DV33NE/S Plantation Shutter Louvre Motor User Manual & Specifications
Comprehensive guide to the DOOYA DV33NE/S Plantation Shutter Louvre Motor, covering installation, operation, specifications, and features. Includes details on battery replacement, remote pairing, and limit setting.
Preview Dooya DM45-serien rørformede motorer
Overview af Dooya DM45-serien af ​​rørmotorer, inklusive elektroniske og radiostyrede modeller. Indeholder tekniske specifikationer, anvendelser til rullejalousier og markiser samt komponentdiagrammer.
Preview DOOYA radiorørmotor - Specifikationer, opsætning og fejlfinding
Omfattende guide til DOOYA AC rørmotorer, der dækker tekniske specifikationer, trinvise opsætningsprocedurer for dot-move, tilføjelse/annullering af emittere og et detaljeret afsnit om fejlfinding af almindelige problemer.
Preview Dooya rørmotorer til indendørs brug - Produktkatalog 2019
Udforsk Dooyas produktkatalog for 2019 med et omfattende udvalg af rørmotorer til indendørs brug. Opdag innovative løsninger til persienner, gardiner og meget mere med fokus på kvalitet og global rækkevidde.
Preview DOOYA 2025 Produktkatalog: Indendørs anvendelse
Udforsk DOOYA 2025 produktkataloget, der indeholder et bredt udvalg af smarte motorløsninger til indendørs brug. Opdag rørmotorer, gardinmotorer, styresystemer og tilbehør designet til forbedret komfort og automatisering.
Preview Dooya DM59 Tubular Motor Series: Specifications and Applications
Overview of Dooya's DM59 series tubular motors, designed for automated shading and opening systems like motorized awnings and roller doors. Includes technical specifications, model details, key features, and certifications.