LEDOne Corp LED Wall Pack Instruction Manual

1. Introduktion

This manual provides comprehensive instructions for the installation, operation, and maintenance of the LEDOne Corp Multi-Watt LED Wall Pack. This fixture is designed for demanding outdoor lighting applications, offering selectable wattage (80W, 100W, 120W) and adjustable color temperature (3000K, 4000K, 5000K) to meet various lighting requirements efficiently.

2. Sikkerhedsoplysninger

ADVARSEL: Risiko for elektrisk stød. Installationen skal udføres af en kvalificeret elektriker i overensstemmelse med alle nationale og lokale el-forskrifter.

• Afbryd strømmen ved afbryderen før installation eller service.
• Sørg for, at forsyningen voltage er kompatibel med armaturets driftsvolumentage (120-277V).
• Do not handle energized fixtures with wet hands or when standing on wet or damp overflader.
• Use only UL/ETL approved components and wiring methods.
• Sørg for, at armaturet er sikkert monteret for at forhindre det i at falde ned.
• Se ikke direkte ind i LED-lyskilden, når den er tændt.

3. Pakkens indhold

Kontroller, at alle komponenter er til stede, før installationen påbegyndes:

• LEDOne Corp LED Wall Pack Fixture
• Instruktionsmanual (dette dokument)
• Monteringshardware

4. Specifikationer

5. Opsætning og installation

The LEDOne Corp Wall Pack is designed for wall mounting and compatibility with standard junction boxes. Follow these steps for secure installation:

1. Forberedelse: Ensure power is disconnected at the circuit breaker. Gather necessary tools (screwdriver, wire strippers, drill, mounting hardware).
2. Monteringssted: Select a suitable wall surface capable of supporting the fixture's weight (approximately 10.63 lbs). The fixture features reinforced mounting points.
3. Monteringsbeslag: Attach the wall mount bracket (if separate) or position the fixture directly over the junction box. Mark and drill pilot holes for the mounting screws.
4. Sikker armatur: Secure the fixture to the wall using the provided mounting hardware. Ensure it is firmly attached and level.
5. Ledningsføring: Open the wiring compartment. Connect the fixture's wires to the supply wires from the junction box:
   • Black wire to Line (L)
   • White wire to Neutral (N)
   • Green wire to Ground (G)
   Use the provided waterproof wire nuts for secure outdoor connections. For 0-10V dimming, connect the purple wire to DIM+ and the gray wire to DIM-.
6. Luk rum: Carefully tuck all wires into the junction box and wiring compartment. Close and seal the compartment cover to maintain IP65 rating.
7. Tænd: Gendan strømmen til afbryderen og test armaturet.

Billede 1: Bagside view of the LED wall pack, illustrating the mounting points and the central access for electrical wiring connections.

Billede 2: Side profile of the LED wall pack, showing the robust construction and a visible screw for secure mounting.

6. Betjeningsvejledning

The LEDOne Corp Wall Pack features adjustable wattage and color temperature settings, typically controlled by internal switches. These switches are usually located within the wiring compartment or on the side of the LED driver housing, accessible after opening the fixture.

Billede 3: Forside view of the LED wall pack with the protective lens removed, revealing the array of LED chips and the internal switches for adjusting wattage og CCT.

1. Justering af Wattage:
   • Ensure power is disconnected before opening the fixture.
   • Find wattage selection switch (often labeled WATT or POWER).
   • Vælg det ønskede wattage: 80W, 100W, or 120W.
   • Close the fixture securely before restoring power.
2. Justering af farvetemperatur (CCT):
   • Ensure power is disconnected before opening the fixture.
   • Locate the CCT selection switch (often labeled CCT or TEMP).
   • Select the desired color temperature: 3000K (warm white), 4000K (cool white), or 5000K (daylight).
   • Close the fixture securely before restoring power.
3. 0-10V dæmpning: This fixture supports 0-10V dimming. Connect a compatible 0-10V dimmer to the purple (DIM+) and gray (DIM-) wires during installation.
4. Photocell/Motion Sensor: The fixture may include or be compatible with external photocells or motion sensors for automated operation. Refer to the specific sensor's instructions for integration.

Billede 4: Vinklet view of the LED wall pack, showcasing its complete assembly and the illuminated LED array.

7. Vedligeholdelse

The LEDOne Corp Wall Pack is designed for minimal maintenance. Regular inspection and cleaning will ensure optimal performance and longevity.

• Rensning: Periodically clean the outer lens and housing with a soft, damp cloth to remove dirt, dust, and debris. Do not use abrasive cleaners or solvents. Ensure power is off before cleaning.
• Inspektion: Annually inspect the fixture for any signs of physical damage, loose connections, or wear on the wiring. Address any issues promptly.
• Forseglinger: Ensure all seals and gaskets are intact to maintain the IP65 weatherproof rating.

8. Fejlfinding

Hvis armaturet ikke fungerer korrekt, skal du se følgende almindelige problemer og løsninger:

If troubleshooting steps do not resolve the issue, contact LEDOne Corp customer support.

9. Garantioplysninger

The LEDOne Corp Multi-Watt LED Wall Pack is backed by a comprehensive 5 års garanti. This warranty covers defects in materials and workmanship under normal use and service. For warranty claims or detailed terms and conditions, please contact LEDOne Corp customer support.

10. Support og kontakt

For further assistance, technical support, or inquiries regarding your LEDOne Corp product, please visit the official LEDONE Store or contact customer service:

Visit the LEDONE Store on Amazon