INEAUTO AX1800 Outdoor WiFi 6 Extender User Manual

1. Introduktion

This manual provides instructions for the INEAUTO AX1800 Outdoor WiFi 6 Extender. This device is designed to extend your existing Wi-Fi signal outdoors, offering dual-band connectivity (5GHz/1200Mbps and 2.4GHz/574Mbps) and utilizing WiFi 6 technology for strong signal penetration and fast speeds. It features an IP67 weatherproof rating, making it suitable for various outdoor environments, and supports Passive PoE for flexible installation.

Image: The AX1800 Outdoor WiFi 6 Extender mounted on a pole near a house and swimming pool, illustrating its outdoor application.

Image: The extender is compatible with various devices including game consoles, cameras, computers, smartphones, smart TVs, and smart locks.

2. Hvad er der i æsken

Bekræft at alle varer er til stede i din pakke:

• AX1800 WiFi 6 Extender
• Passiv PoE-adapter
• Ethernet kabel
• monteringspakke
• Hurtig installationsvejledning

3. Fysisk overview

The extender features multiple antennas for enhanced signal coverage and ports for power and network connections. Proper antenna positioning is crucial for optimal performance.

Image: The extender with its 4 built-in 8dBi antennas and dual signal amplifiers, highlighting its wide coverage capabilities.

Antenneplacering:

For visual guidance on antenna positioning, refer to the video in the Setup section, specifically from timestamp 2:24 til 3:16.

1. Place the device on a flat surface. Lift the two side antennas upward by 45 degrees.
2. Rotate each of the four center antennas 180 degrees clockwise or counter-clockwise as needed.
3. Pull all antennas straight upward and snap them into the slots securely.

4. Opsætningsvejledning

Follow these steps to set up your INEAUTO AX1800 Outdoor WiFi 6 Extender. A comprehensive setup video is provided below:

1. Power On the Extender: Plug the WiFi extender into a power outlet near your router using the Passive PoE adapter. Ensure the Ethernet cable is connected to the PoE port on the extender. Wait until the LED indicator turns solid.
2. Opret forbindelse til repeater WiFi: On your smartphone or computer, connect to the Wi-Fi network named "Repeater_XXX". If you cannot find the SSID, turn on Airplane Mode, then turn it off to refresh available networks.
3. Adgangsopsætningsside: Once connected, your device should automatically redirect to the extender's login page. If not, open a web browser and enter the default IP address (refer to the Quick Installation Guide for the specific IP).
4. Choose Setup Mode: Select your preferred connection mode (Repeater Mode, AP Mode, or Router Mode) and tap "NEXT" to proceed.
5. Tilslut til din router: Select your router's 5GHz or 2.4GHz Wi-Fi network from the list. Enter the correct password for your router's network, then tap "NEXT". Note: Under repeater mode, the password of the extender remains the same as your router's.
6. Komplet opsætning: Click the "FINISH" button to complete the settings. The setup is complete. Reconnect to the network after approximately 30 seconds. Check the signal indicator status of the extender when using it.

Image: Passive PoE connection setup for the extender. The PoE adapter is for indoor use only.

5. Driftstilstande

The INEAUTO AX1800 Outdoor WiFi 6 Extender supports multiple operating modes to suit various networking needs:

• Repeater-tilstand: Extends the coverage of an existing Wi-Fi network. Ideal for eliminating Wi-Fi dead zones.
• AP (Adgangspunkt) Tilstand: Converts a wired network connection into a wireless access point. Suitable for creating a new Wi-Fi hotspot.
• Routertilstand: Fungerer som en primær router, der giver internetadgang til tilsluttede enheder.

Image: Visual representation of the different operating modes and their network configurations.

6. Vedligeholdelse

To ensure optimal performance and longevity of your outdoor Wi-Fi extender, consider the following maintenance tips:

Image: The extender's design for various weather conditions, including sun, snow, wind, rain, thunder, and frost.

• Regelmæssig rengøring: Periodically clean the exterior of the device to remove dust, dirt, or debris that may accumulate, especially in outdoor environments. Use a soft, dry cloth.
• Tjek forbindelser: Ensure all cable connections (Ethernet, power) are secure and free from damage.
• Firmwareopdateringer: Tjek producentens website for any available firmware updates. Keeping the firmware updated can improve performance, security, and stability.
• Miljøhensyn: While the device is IP67 weatherproof, avoid placing it in locations prone to extreme physical impact or prolonged submersion. Ensure the PoE adapter is installed indoors as it is not waterproof.

7. Fejlfinding

If you encounter issues with your extender, refer to the following common solutions:

• Ingen internetforbindelse:
  • Bekræft, at din primære router har en aktiv internetforbindelse.
  • Ensure the extender is properly powered on and connected to the PoE adapter.
  • Check the Ethernet cable connection between the PoE adapter and the extender.
  • Confirm that the extender is successfully connected to your main router's Wi-Fi network (check setup steps).
  • Prøv at genstarte både din primære router og extenderen.
• Cannot Find Repeater Wi-Fi SSID:
  • Sørg for, at forlængeren er tændt.
  • On your mobile device, toggle Airplane Mode on and off to refresh the Wi-Fi network list.
  • Move closer to the extender to ensure you are within range.
• Langsom forbindelseshastighed:
  • Ensure the extender is placed in an optimal location, ideally halfway between your router and the desired coverage area, with a clear line of sight.
  • Minimér interferens fra andre elektroniske enheder.
  • Check your main router's internet speed.

How to Reset Your Extender:

For visual guidance on resetting the extender, refer to the video in the Setup section, specifically from timestamp 1:40 til 2:24.

1. Plug the extender into a power outlet and wait for about 30 seconds until it fully boots.
2. Using a pointed object (like a paperclip or pen tip), press and hold the Reset Button for 10 seconds. The LED indicators will typically flash or change color to confirm the reset.
3. Release the button. The extender will restart with factory default settings. You will need to reconfigure it following the setup instructions.

8. Specifikationer

9. Garanti og support

For detailed warranty information, please refer to the warranty card included with your product or visit the official INEAUTO website. For technical support, troubleshooting assistance, or to inquire about replacement parts, please contact INEAUTO customer service through their official channels.

Du kan typisk finde kontaktoplysninger på producentens webwebsted eller i produktemballagen.