Valkyrie A360 ARGB All-in-One CPU Liquid Cooler User Manual

1. Introduktion

This manual provides detailed instructions for the installation, operation, and maintenance of your Valkyrie A360 ARGB All-in-One (AIO) CPU Liquid Cooler. Please read this manual thoroughly before installation to ensure proper setup and optimal performance. Keep this manual for future reference.

2. Sikkerhedsoplysninger

• Sørg for, at dit computersystem er slukket og taget stikket ud af stikkontakten inden installation.
• Handle components with care to avoid damage. Avoid touching the cold plate surface directly.
• Do not open the liquid cooler's pump or radiator; it is a sealed unit. Tampgarantien bortfalder.
• Hold produktet væk fra ekstreme temperaturer, fugtighed og direkte sollys.
• Use only the provided mounting hardware to prevent damage to your CPU or motherboard.

3. Pakkens indhold

Bekræft, at alle nedenstående komponenter er til stede i din pakke:

• Valkyrie A360 ARGB AIO Liquid Cooler (Radiator, Pump/CPU Block, Tubing)
• 3 x 120 mm ARGB blæsere
• Intel Mounting Bracket Kit (LGA 1700, 1200, 115X, 2066, 2011)
• AMD Mounting Bracket Kit (AM5, AM4)
• Fan Screws and Radiator Mounting Screws
• Termopasta (påført på forhånd eller i tube)
• ARGB Controller/Cables (if included)
• Brugermanual

Image: The Valkyrie A360 ARGB AIO Liquid Cooler showing the radiator, three ARGB fans, and the pump/CPU block unit.

4. Opsætning og installation

4.1. Forberedelse

• Sluk for computeren, og frakobl alle kabler.
• Åbn computerens kabinet for at få adgang til bundkortet og CPU-området.
• If replacing an existing cooler, carefully remove it and clean any old thermal paste from the CPU surface using isopropyl alcohol.

4.2. Installation af radiator og ventilator

1. Attach the three 120mm ARGB fans to the radiator using the long fan screws provided. Ensure the fan airflow direction is appropriate for your case (typically exhausting air out or pulling air in).
2. Mount the assembled radiator and fans to an available 360mm mounting location in your PC case (e.g., top, front). Use the shorter radiator mounting screws.

Image: The radiator with three white fans attached, ready for case installation.

4.3. Installation af CPU-blok

1. For Intel Sockets: Install the appropriate Intel backplate behind the motherboard. Attach the Intel mounting standoffs to the motherboard.
2. For AMD Sockets: Remove the stock AMD retention brackets from the motherboard, but keep the original backplate. Attach the AMD mounting standoffs to the motherboard.
3. Hvis der ikke er påført termisk pasta på den kolde plade på forhånd, skal du påføre en lille mængde på størrelse med en ært i midten af ​​din CPU's integrerede varmespreder (IHS).
4. Carefully place the CPU block onto the CPU, aligning the mounting holes with the standoffs.
5. Secure the CPU block with the thumb screws or nuts, tightening them in a diagonal pattern until snug. Do not overtighten.

Billede: Et nærbillede view of the Valkyrie A360 CPU block installed on a motherboard, illuminated with blue ARGB lighting.

4.4. Kabelforbindelser

1. Connect the pump's 3-pin or 4-pin power cable to the motherboard header labeled "AIO_PUMP," "CPU_OPT," or "SYS_FAN" (consult your motherboard manual for the recommended header).
2. Connect the ARGB cables from the fans and pump to the included ARGB controller or directly to a 5V 3-pin ARGB header on your motherboard. Ensure correct pin alignment to avoid damage.
3. Connect the fan power cables to available fan headers on your motherboard or to a fan hub/controller.

Image: The Valkyrie A360 AIO cooler fully installed within a white PC case, showcasing the blue ARGB lighting on the fans and CPU block.

5. Betjeningsvejledning

5.1. Første opstart

After completing the installation, close your PC case, reconnect all external cables, and power on your computer. Observe the cooler for any unusual noises or leaks. Check your system's BIOS/UEFI for CPU temperature readings to confirm proper operation.

5.2. ARGB-lysstyring

If connected to a motherboard's 5V 3-pin ARGB header, you can control the lighting effects using your motherboard's RGB software (e.g., ASUS Aura Sync, MSI Mystic Light, Gigabyte RGB Fusion, ASRock Polychrome Sync). If using the included ARGB controller, refer to its specific instructions for mode and color selection.

Image: The Valkyrie A360 AIO cooler installed in a white PC case, displaying vibrant rainbow ARGB lighting effects on the fans and CPU block.

6. Vedligeholdelse

• Støvrensning: Periodically clean the radiator fins and fan blades to prevent dust buildup, which can impede airflow and cooling performance. Use compressed air or a soft brush.
• Visuel inspektion: Regularly check the tubing and connections for any signs of leaks or damage.
• Ingen påfyldning af kølevæske: The Valkyrie A360 is a sealed AIO unit and does not require coolant refills. Opening the unit will void the warranty.

7. Fejlfinding

8. Specifikationer

9. Garanti og support

Valkyrie products are backed by a limited warranty against defects in materials and workmanship. The specific warranty period may vary by region. Please retain your proof of purchase for warranty claims.

For technical support, troubleshooting assistance, or warranty inquiries, please visit the official Valkyrie webwebstedet eller kontakt deres kundeserviceafdeling. Kontaktoplysninger kan typisk findes på produktemballagen eller den officielle webwebsted.

Note: Opening the sealed AIO unit or using non-approved components may void your warranty.