1. Introduktion og overview
The ESX QUANTUM QS-FOUR is an ultra-compact 4-channel Class D amplifier designed to significantly upgrade your car audio system. This powerful yet miniature 4-channel version measures only 90 x 35 x 80 mm, making it one of the smallest amplifiers in its class. It delivers an impressive 4 x 60 Watts RMS, providing substantial power to factory or aftermarket speakers.
The QS-FOUR features exceptionally low distortion (THD+N < 0.007% at 5W/RMS) and high efficiency (up to 90%), ensuring clear and dynamic sound reproduction. Its compact size allows for flexible installation, often directly behind the dashboard, making it an ideal plug-and-play solution for vehicles. The amplifier's low current draw (5-10 Amps) means it can often utilize existing factory power cables. Additionally, the QS-FOUR includes low-level outputs for connecting active subwoofers or larger monoblock amplifiers, offering expandability for enhanced bass.
2. Sikkerhedsoplysninger
- Always disconnect the vehicle's battery before beginning any installation work to prevent electrical shorts and damage.
- Professional installation is recommended. Incorrect wiring can cause serious damage to the ampskade på køretøjet eller personskade.
- Ensure all wiring is properly insulated and secured to prevent short circuits and vibrations.
- Installer ikke amplifier in locations exposed to moisture, excessive heat, or direct sunlight.
- Brug passende ledninger til strøm- og højttalertilslutninger som angivet i installationsafsnittet.
- Protect all power cables with an inline fuse located close to the battery.
- Undgå at placere amplifier where it could obstruct vehicle controls or safety devices.
3. Pakkens indhold
Kontroller venligst pakkens indhold for at sikre, at alle varer er til stede og ubeskadigede:
- ESX QUANTUM QS-FOUR Amplifier enhed
- High-Level Input Wiring Harness with EPS (Error Protection System)
- Power Input Wiring Harness
- Speaker Output Wiring Harness
- RCA Line-Out Cables
- Inline Fuse Holder with Fuse
- Monteringsskruer
4. Produktfunktioner
- Ultra-kompakt design: Dimensions of 90 x 35 x 80 mm for flexible installation.
- Høj effekt: 4 x 60 W RMS at 2 Ω, 4 x 45 W RMS at 3 Ω, 4 x 35 W RMS at 4 Ω, or 2 x 120 W RMS bridged at 4 Ω.
- Full Range Class D Technology: Efficient power delivery with minimal heat generation.
- Selectable Crossover Filters: Front and Rear Highpass/Lowpass filters switchable at 80 Hz.
- High-Level Inputs with EPS: Error Protection System for seamless integration with factory head units.
- Auto-Turn-On Function: Automatic power-on via DC offset or VOX (signal detection).
- 2-Channel RCA Line-Out: For connecting external active subwoofers or additional amplivførere.
- 12V Remote Output: Provides a remote signal for other devices.
- Bred frekvensrespons: 10 Hz til 60 kHz.
- Low Total Harmonic Distortion (THD+N): < 0.007% at 5W/RMS.
- Høj effektivitet: Up to 90% for reduced power consumption.
5. Opsætning og installation
5.1 Ledningsforbindelser
Before making any connections, ensure the vehicle's battery is disconnected. Refer to the diagrams below for proper wiring.
Strømindgang:
- + 12V: Connect to the positive terminal of the car battery via an inline fuse (not included, but a fuse holder is provided).
- GND: Connect to a solid, unpainted metal point on the vehicle chassis. Ensure a good ground connection.
- REM (fjernbetjening): Connect to the remote output of your head unit. If using high-level inputs with Auto-Turn-On, this connection may not be necessary.
Højttaler output:
Connect your speakers to the designated terminals. Ensure correct polarity (positive to positive, negative to negative). The ampLifier understøtter 4-kanals stereo eller 2-kanals brokoblet drift.
- FL+/FL-: Venstre forreste højttaler
- FR+/FR-: Højre forreste højttaler
- RL+/RL-: Venstre baghøjttaler
- RR+/RR-: Højre baghøjttaler
- Brokoblet tilstand: For 2-channel operation, connect the positive of the left speaker to FL+ and the negative to FR-. For the right speaker, connect positive to RL+ and negative to RR-. Refer to the manual for specific bridging instructions.
Indgangsforbindelser:
- Input på højt niveau: Use the provided harness to connect to your head unit's speaker outputs. The EPS (Error Protection System) ensures compatibility with various factory systems.
- RCA Line-Out: Use the RCA cables to connect to an active subwoofer or another amplivligere.
5.2 Indledende indstillinger
- Level Input (Gain): Start with the gain knobs set to minimum (MIN). Gradually increase the gain until the sound is clear and distortion-free at your desired listening volume. Avoid setting the gain too high, as this can introduce distortion.
- X-OVER (Delefilter):
- FULD: Full range audio (no filter).
- HP (High Pass): Allows frequencies above 80 Hz to pass, typically used for full-range speakers to remove bass.
- LP (Low Pass): Allows frequencies below 80 Hz to pass, typically used for subwoofers (though this amplifier is not primarily for subwoofers, it can be used for mid-bass applications).
- AUTO TURN-ON:
- OFF: Amplifier turns on via the REM wire.
- VOX: Amplifier turns on when an audio signal is detected (signal sensing).
- DC: Amplifier turns on when a DC offset is detected on the high-level inputs (common with factory head units).
6. Betjeningsvejledning
Once properly installed and configured, the ESX QUANTUM QS-FOUR amplifier operates automatically with your vehicle's audio system.
- Tænd/sluk: De amplifier will power on and off with your head unit, depending on the selected AUTO TURN-ON mode (REM, VOX, or DC). The 'POWER' LED on the rear panel will illuminate when the amplifier er aktiv.
- Lydafspilning: Play audio through your head unit as usual. The amplifier will provide enhanced power and clarity to your speakers.
- Justering af lydstyrke: Control the overall system volume using your head unit. If distortion occurs at high volumes, slightly reduce the amplifiers forstærkningsindstilling.
- Beskyttelsestilstand: If the 'PROTECT' LED illuminates, the ampApparatet er gået i beskyttelsestilstand på grund af et problem (f.eks. kortslutning, overophedning, lavt volum)tage). Turn off your audio system and vehicle, then troubleshoot the cause before restarting.
7. Vedligeholdelse
- Rensning: Brug en blød, tør klud til at rengøre ampydersiden af apparatet. Brug ikke skrappe kemikalier eller slibende rengøringsmidler.
- Forbindelser: Kontrollér regelmæssigt alle strøm-, jord- og højttalerforbindelser for at sikre, at de er fastgjorte og fri for korrosion.
- Ventilation: Sørg for amplifier's cooling fins are not obstructed to allow for proper heat dissipation.
- Udskiftning af sikring: If the inline fuse blows, replace it only with a fuse of the same type and rating to prevent damage.
8. Fejlfinding
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Ingen lyd fra højttalerne | Ingen strøm til amplifier; Incorrect input/output wiring; Head unit not sending signal; Amplifier i beskyttelsestilstand. | Check power and ground connections; Verify remote turn-on signal; Check speaker and input wiring; Ensure head unit is on and playing audio; Check 'PROTECT' LED. |
| Forvrænget lyd | Forstærkningen er indstillet for højt; Forkerte delefiltreindstillinger; Uoverensstemmelse mellem højttalerimpedans; Beskadigede højttalere. | Reduce gain level; Adjust crossover settings; Verify speaker impedance is within amplifier's range; Test speakers individually. |
| 'PROTECT' LED is on | Short circuit in speaker wiring; Overheating; Low/high voltage; Speaker impedance too low. | Turn off system, check all speaker wires for shorts; Ensure adequate ventilation; Check vehicle's battery voltage; Verify speaker impedance. |
| Ampkøleren tænder ikke | No +12V power; No ground connection; No remote signal (if not using Auto-Turn-On); Blown fuse. | Check fuse, power, and ground wires; Verify remote wire connection or Auto-Turn-On setting. |
9. Specifikationer
| Feature | Specifikation |
|---|---|
| Modelnummer | QS-FOUR |
| Kanaler | 4 |
| Output Power (RMS @ 4 Ω) | 4 x 35 W |
| Output Power (RMS @ 3 Ω) | 4 x 45 W |
| Output Power (RMS @ 2 Ω) | 4 x 60 W |
| Bridged Output Power (RMS @ 4 Ω) | 2 x 120 W |
| Frekvensrespons | 10 Hz – 60 kHz |
| Total Harmonic Distortion (THD+N @ 5W/RMS) | < 0.007 % |
| Effektivitet | Op til 90 % |
| Delefiltre | HP/LP switchable @ 80 Hz (Front/Rear) |
| Input bindtage | 12V DC (Min/Max) |
| Dimensioner (L x B x H) | 90 x 80 x 35 mm (3.54 x 3.15 x 1.38 tommer) |
| Monteringstype | Frit stående |
| Overholdelse | CE |
10. Garanti og support
The ESX QUANTUM QS-FOUR amplifier comes with a manufacturer's warranty. Please refer to the warranty card included with your product or contact your authorized ESX dealer for specific warranty terms and conditions.
For technical support, installation assistance, or service inquiries, please contact your point of purchase or visit the official ESX Car-Audio webhjemmeside for kontaktoplysninger og ressourcer.