INEAUTO AX3000 WiFi 6 Extender User Manual

1. Introduktion

This manual provides detailed instructions for the installation, operation, and maintenance of your INEAUTO AX3000 WiFi 6 Extender. This device is designed to extend wireless network coverage in outdoor environments, offering high-speed and stable connectivity. Please read this manual thoroughly before use to ensure proper setup and optimal performance.

2. Sikkerhedsoplysninger

For at forhindre skader på enheden eller personskade på dig selv eller andre, bedes du overholde følgende sikkerhedsforanstaltninger:

• Sørg for, at strømkilden passer til enhedens krav.
• Åbn ikke enheden, og forsøg ikke at reparere den. Overlad al service til kvalificeret personale.
• Keep the device away from excessive heat, humidity, and direct sunlight.
• The PoE converter is not waterproof and must be installed indoors.
• Ensure proper grounding and lightning protection during outdoor installation.

3. Pakkens indhold

Bekræft at alle varer er til stede i din pakke:

• 1 x AX3000 WiFi 6 Extender
• 1 x PoE-strømadapter
• 1 x Ethernet-kabel
• Mounting Accessories (Cable ties, metal strap, screws, wall plugs)
• Hurtig brugervejledning

Image: Contents included in the product package, showing the extender, PoE adapter, Ethernet cable, and mounting hardware.

4. Produktet er slutview

4.1. Enhedsfunktioner

• Ultra-Fast WiFi 6 Technology: Dual-band support (5GHz/2400Mbps & 2.4GHz/600Mbps) for smooth HD streaming, gaming, and browsing.
• Gigabit Ethernet-porte: Two Gigabit Ethernet ports, one supporting up to 2.5Gbps for faster wired connections.
• Holdbarhed i alt vejr: IP67 waterproof housing and lightning protection for reliable performance in extreme outdoor conditions.
• Powerful Coverage: Equipped with 6 high gain 8dBi antennas and dual PA/LNA amplifiers for extended signal coverage up to 300 meters.
• Flexible Passive PoE Installation: Power and data via a single Ethernet cable, ideal for hard-to-reach outdoor areas. (Note: PoE converter is not waterproof).
• Alsidige tilstande: Supports AP, router, and repeater modes to adapt to various network scenarios.
• Forbedret sikkerhed: WPA/WPA3 and WPA-PSK/WPA3-PSK protocols for network security.

Image: The INEAUTO AX3000 WiFi 6 Extender mounted on a pole in an outdoor backyard setting.

Image: Depiction of the outdoor WiFi 6 extender's IP67 weatherproof and lightning protection, showing its resilience to rain, snow, thunder, wind, sun, and frost.

Image: Illustration of the WiFi 6 dual-band concurrent feature, highlighting 2.4GHz (572Mbps) and 5GHz (2402Mbps) speeds for HD video, music, and gaming.

Image: The extender shown with its six 8dBi high-gain antennas, illustrating its 300-meter signal coverage for large outdoor spaces.

4.2. Enhedsdimensioner

Image: Detailed dimensions of the AX3000 WiFi 6 Extender (20cm/7.9in x 14cm/5.5in x 6.7cm/2.6in), its antennas (25.8cm/10.2in), Ethernet cable (100cm/39.4in), and PoE adapter (8.4cm/3.3in x 4.7cm/1.9in x 3.7cm/1.5in).

5. Opsætning

5.1. Indledende opsætningstrin

1. Power On the Extender: Plug the WiFi extender into a power outlet near your router. Wait until the LED indicator turns solid. Note: The cable must be connected to the PoE port.


Image: Diagram showing the PoE adapter connecting to a power outlet, then via RJ45 cables to the Gigabit LAN port of the extender. A note indicates the PoE adapter is not waterproof and must be indoors.

2. Opret forbindelse til repeater WiFi: Connect to the WiFi "Repeater_XXX" on your smartphone. Note: If you can't find the SSID name of the Repeater WiFi, turn on Airplane Mode, then turn it off to refresh available networks.
3. Adgangsopsætningsside: Once connected, your phone will automatically jump to the extender's login page.
4. Choose Setup Mode: Select your preferred connection mode (Repeater, AP, or Router), then tap "NEXT" to proceed.
5. Tilslut til din router: Select your router's 5GHz WiFi network from the list, enter the correct password, then tap "NEXT". Note: Under repeater mode, the password of the extender remains the same as your router's.
6. Komplet opsætning: Click the "Finish" button to complete the settings. Setup is complete, reconnect to the network after 30 seconds. Please check the signal indicator status of the extender when using it.

5.2. Antenneorientering

Proper antenna orientation is crucial for optimal signal strength and coverage. Follow these steps:

1. Place the device as shown. Lift the two side antennas by 45°, and the four center antennas by 45° as well.
2. Flip the two side antennas upward 180°. Then rotate each of the four center antennas 180° clockwise or counterclockwise as indicated.
3. Pull all antennas straight upward and snap them into the slots securely.
4. Færdig.

6. Driftstilstande

The INEAUTO AX3000 WiFi 6 Extender supports multiple operating modes to suit various networking needs:

• AP (Adgangspunkt) Tilstand: Converts a wired network connection into a wireless one, ideal for creating a new WiFi hotspot.
• Routertilstand: Fungerer som en primær router, der giver internetadgang til tilsluttede enheder.
• Repeater-tilstand: Extends the range of an existing wireless network, eliminating dead zones.

Image: Visual representation of the different operating modes: AP/Router Mode, Repeater Mode, and AP+Repeater Mode, illustrating how the extender integrates into various network setups.

7. Vedligeholdelse

Regular maintenance helps ensure the longevity and optimal performance of your extender:

• Rensning: Tør enheden regelmæssigt af med en blød, tør klud. Brug ikke flydende rengøringsmidler eller aerosoler.
• Firmwareopdateringer: Tjek producentens website for the latest firmware updates to ensure security and performance improvements.
• Miljøforhold: Ensure the device is installed in an environment within its specified operating temperature range (-30°C to 70°C).
• Kabelinspektion: Regularly inspect Ethernet cables for any signs of wear or damage, especially those exposed to outdoor elements.

8. Fejlfinding

If you encounter issues with your INEAUTO AX3000 WiFi 6 Extender, refer to the following common problems and solutions:

8.1. How to Reset Your Extender

If the extender is not functioning correctly or you wish to revert to factory settings, you can perform a hard reset:

1. Plug the extender into a power outlet and wait for about 30 seconds until it fully boots.
2. With the extender powered on, use a paperclip or a thin object to press and hold the Reset Button for 10 seconds. The LED indicator will flash rapidly.
3. Release the button. The extender will restart with factory default settings.

9. Specifikationer

10. Garanti og support

For warranty information and technical support, please refer to the official INEAUTO webwebstedet eller kontakt deres kundeservice direkte. Gem din købskvittering til garantikrav.

Online ressourcer:

• Official INEAUTO Webwebsted: Visit INEAUTO Store
• Brugermanual (PDF): Download PDF Manual