Indledning
The EZDIY-FAB Shield 24Pin 180° Angle Adapter is designed to redirect your motherboard's 24-pin power cable, providing a cleaner aesthetic and improved cable management within your PC build. It features an integrated infinity mirror ARGB lighting system for visual enhancement and supports 5V 3-pin ARGB synchronization with compatible motherboards.
Produktegenskaber
- Infinity Mirror ARGB Design: Incorporates a shield-inspired infinity mirror with built-in ARGB lighting, adding depth and a soft visual glow to your PC.
- 180° Cable Routing: Redirects the motherboard power cable for cleaner routing, reducing visible cable clutter and connector strain.
- Stabil strømforbindelse: Equipped with high-conductivity copper alloy terminals to ensure stable power transmission and secure contact for ATX 24-pin motherboard connections.
- 5V 3-Pin ARGB Sync: Connects to a compatible 5V 3-pin ARGB motherboard header or controller for synchronized lighting effects.
Sikkerhedsoplysninger
Please read and understand the following safety precautions before installation:
- Ensure your PC is powered off and unplugged from the wall outlet before installing or removing any components.
- Discharge any static electricity from your body by touching a grounded metal object before handling PC components.
- Handle the adapter by its body, avoiding contact with the electrical pins.
- Do not force the adapter into place. If it does not fit easily, recheck compatibility and orientation.
- Opbevares utilgængeligt for børn.
Installationsvejledning
1. Pre-Installation Clearance Check
Before installation, verify that there is sufficient space between your motherboard's 24-pin connector and the PC case routing hole. Ensure 8-10 mm of clearance around the motherboard 24-pin ATX connector to avoid interference with adapter installation or blocking access to nearby ports. Check your motherboard layout before proceeding.
2. Connecting the Adapter to the Motherboard
- Align the EZDIY-FAB 24-pin adapter with the 24-pin ATX power connector on your motherboard.
- Gently but firmly press the adapter into the motherboard connector until it is fully seated. There should be no visible gap between the adapter and the motherboard connector.
- Ensure the latch/buckle on the motherboard side is properly engaged.
3. Connecting the PSU Cable to the Adapter
- Take your power supply unit's (PSU) 24-pin ATX cable.
- Align the PSU cable with the input port on the EZDIY-FAB 24-pin adapter.
- Push the PSU cable into the adapter until it clicks into place. Ensure the latch/buckle on the cable side is properly engaged.
4. ARGB Connection
- Locate the 5V 3-pin ARGB cable extending from the EZDIY-FAB adapter.
- Connect this cable to an available 5V 3-pin ARGB header on your motherboard or a compatible ARGB controller.
- Ensure the connection is made with the correct orientation to prevent damage. Do not connect to a 12V RGB header.
Operation
Once installed and connected, the infinity mirror ARGB lighting will illuminate. To control the lighting effects:
- If connected to a motherboard ARGB header, use your motherboard's dedicated ARGB software (e.g., ASUS Aura Sync, GIGABYTE RGB Fusion, MSI Mystic Light Sync, ASRock Polychrome Sync) to customize lighting patterns, colors, and synchronization with other ARGB components.
- If connected to an external ARGB controller, refer to the controller's manual for specific lighting control instructions.
Opretholdelse
The EZDIY-FAB Shield 24Pin 180° Angle Adapter requires minimal maintenance:
- Periodically check for dust accumulation on the adapter and gently clean with compressed air or a soft, dry cloth.
- Ensure all connections remain secure. Avoid pulling on cables directly.
- Do not attempt to disassemble the adapter, as this may void the warranty and cause damage.
Fejlfinding
| Problem | Mulig årsag | Løsning |
|---|---|---|
| PC does not power on after installation. | Loose or incorrect connection of the 24-pin power cable. | Ensure the adapter is fully seated on the motherboard and the PSU 24-pin cable is securely connected to the adapter. Check for any visible gaps or unlatched buckles. |
| ARGB-belysningen virker ikke. | Incorrect ARGB connection, incompatible header, or software issue. | Verify the 5V 3-pin ARGB cable is correctly connected to a 5V 3-pin ARGB header (not 12V RGB). Check your motherboard's ARGB software settings. Ensure the ARGB cable is not damaged. |
| Adapter does not fit in the PC case. | Insufficient clearance between motherboard 24-pin connector and case. | Refer to the "Pre-Installation Clearance Check" section. This adapter requires specific clearance. If clearance is insufficient, the adapter may not be compatible with your case/motherboard combination. |
Specifikationer
| Feature | Detalje |
|---|---|
| Modelnummer | EZDPI231 |
| Mærke | EZDIY-FAB |
| Connector Type | 24-bens ATX (han-til-hun) |
| Antal pins | 24 |
| Kabeltype | Magt |
| Kompatible enheder | Desktop pc'er |
| Særlige funktioner | Infinity Mirror ARGB Light, Shield-Inspired Design, 180-Degree Configuration |
| ARGB Sync | 5V 3-Pin ARGB (Addressable RGB) |
| Wattage | 24 watt |
| Maksimal voltage | 12 volt |
| Farve | Sort |
| Dimensioner (ca.) | 10.6 x 6.1 x 4 cm |
| Vægt (ca.) | 70 g |
Garanti og support
This EZDIY-FAB product comes with a 2 års garanti from the date of purchase. For technical support, warranty claims, or further assistance, please contact EZDIY-FAB customer service through their official webwebstedet eller forhandleren, hvor produktet blev købt. Gem venligst din købsbevis for at validere garantien.
Manufacturer Contact Information: Dongguan, China