1. Introduktion
This manual provides detailed instructions for the installation, operation, and maintenance of the Generic XM-18D Full Automatic Egg Incubator Controller. This device is designed to precisely manage temperature and humidity within an egg incubator, ensuring optimal conditions for successful incubation. Please read this manual thoroughly before use to ensure correct operation and to prevent damage to the unit or injury.
2. Sikkerhedsoplysninger
- Sørg for, at driftsmængdentage (AC 180V~240V, 50HZ) matches your power supply.
- Do not expose the controller to direct water or excessive humidity (relative humidity should be less than 85%).
- Avoid operating the device in ambient temperatures outside the -20℃ to 70℃ range.
- All wiring should be performed by a qualified individual to prevent electrical hazards.
- Opbevares utilgængeligt for børn.
- Afbryd strømmen, før du udfører vedligeholdelse eller rengøring.
3. Pakkens indhold
Bekræft at alle varer er til stede i pakken:
- 1 x XM-18D Incubator Controller Thermostat Hygrometer
- 1 x temperatursensor
- 1 x Humidity Sensor
4. Produktet er slutview
The XM-18D controller features a digital display for real-time monitoring and control of incubation parameters. It includes multiple output lines for various incubator functions.
Figur 4.1: Front view of the XM-18D Incubator Controller. This image displays the main unit with its digital readouts and control buttons.
Figur 4.2: Labeled front panel of the XM-18D controller. Key components include the humidity display, temperature display, SET switch, fan switch, light switch, SET key, Enter button, work lights, and +/- buttons.
Figur 4.3: Dimensions of the XM-18D controller. The unit measures approximately 20cm in length, 14cm in width, and 12cm in height.
Figur 4.4: Key features of the XM-18D controller. It offers real-time measurement and control of temperature and humidity, along with button touch operation for simple and convenient use.
Figur 4.5: Internal components highlighting the high-quality circuit and microcomputer chip. These ensure stable performance, accurate control, and strong anti-interference capabilities.
5. Opsætning
Before operating the XM-18D controller, ensure all necessary connections are made correctly. Refer to the wiring diagram and the video for visual guidance.
5.1 Sensortilslutning
Connect the humidity sensor and temperature sensor to their designated terminals on the controller's back panel.
Figur 5.1: Detailed wiring diagram for the XM-18D controller. This diagram illustrates connections for the lamp bulb, uniform temperature, heaters, humidifier, egg turning motor, and ventilating fan, along with the power line, humidity sensor, and temperature sensor connections.
Video 5.1: This video demonstrates the correct connection of the power cable, humidity sensor, and temperature sensor to the XM-18D controller. It also shows the initial power-on sequence and basic display functions.
- Locate the terminals for the Humidity Sensor and Temperature Sensor on the back of the controller.
- Carefully connect the wires from the Humidity Sensor to the corresponding terminals.
- Connect the wires from the Temperature Sensor to its designated terminals.
5.2 Strømtilslutning
Connect the power cable to the controller and then to a suitable power outlet.
- Connect the power cable to the main power input terminals (L and N) on the controller.
- Plug the power cable into an AC 180V~240V, 50HZ power source.
5.3 Udgangsforbindelser
Connect the various incubator components (heaters, fan, humidifier, egg turning motor, light) to their respective output terminals as indicated in the wiring diagram (Figure 5.1).
- Connect primary and auxiliary heaters to the HEATI and HEAT2 terminals.
- Connect the exhaust fan to the appropriate fan terminal.
- Connect the egg turning motor to the LEFT and RIGHT terminals.
- Connect the humidifier to the WET terminal.
- Connect the incubator light to the LIGHT terminal.
6. Betjeningsvejledning
The XM-18D controller is designed for user-friendly operation. Follow these steps to configure and monitor your incubator.
6.1 Tænd og startdisplay
- After all connections are secure, turn on the main power switch on the controller.
- The digital displays will illuminate, showing current temperature (PV TEM) and humidity (PV WET%). The set temperature (SV TEM) and set humidity (SV WET%) will also be displayed.
- If an alarm sounds, manually dismiss it by pressing the "Cancel Alarm" button.
6.2 Setting Temperature and Humidity
To adjust the desired temperature and humidity settings:
- Tryk på SÆT button to enter the setting mode. The temperature setting value will flash.
- Brug UP og NED piletasterne til at justere den ønskede temperatur.
- Trykke SÆT again to move to the humidity setting. The humidity setting value will flash.
- Brug UP og NED arrow buttons to adjust the desired humidity.
- Trykke OK or SÆT to confirm and save the settings.
6.3 Egg Turning Settings
The controller supports automatic egg turning. Refer to the manual's detailed parameters for specific timing adjustments.
- Tryk på Egg Turning button to manually initiate an egg turn or to access egg turning settings (if applicable).
- The egg rotation cycle and period can be adjusted in the advanced settings (refer to the full technical specifications for parameter codes).
6.4 Fan and Light Control
The controller provides dedicated switches for the fan and internal light.
- Brug FAN switch to turn the incubator's internal fan on or off.
- Brug LYS switch to control the internal light of the incubator.
7. Specifikationer
| Feature | Værdi |
|---|---|
| Model nr. | XM-18D |
| Dimensioner | 30 x 12 x 7.5 cm (11.81 x 4.72 x 2.95 tommer) |
| Vægt | 0.95 kg (2.64 pund) |
| Temperaturvisningsområde | 0~40.5°C |
| Temperaturmålingsnøjagtighed | ±0.1°C |
| Visningsområde for fugtighed | 0~99% RH |
| Humidity Control Accuracy | ± 3% RH |
| Udgangslinjer | 6 lines (primary heating, auxiliary heating, exhaust, turn left, turn right, moisten) |
| Udgangsstrøm | Primary and auxiliary heating 30A, other outputs 10A |
| Egg Rotation Time (Max) | 999 gange |
| Egg Rotation Cycle (Default) | 0~999 minutes (90 minutes) |
| Egg Rotation Period (Default) | 0~999 seconds (180 seconds) |
| Air Exchange Cycle (Default) | 0~999 minutes (120 minutes) |
| Air Exchange Period (Default) | 0~999 seconds (15 seconds) |
| Measuring Line Length | Ca.. 1.5 meter |
| Operation Voltage | AC 180V~240V, 50HZ |
| Relativ luftfugtighed (drift) | Mindre end 85 % |
| Ambient Temperature (Operating) | -20℃~70℃ |
8. Vedligeholdelse
Proper maintenance ensures the longevity and accurate performance of your XM-18D controller.
- Rensning: Regularly wipe the controller's surface with a soft, dry cloth. Do not use abrasive cleaners or solvents. Ensure no liquids enter the device.
- Sensorpleje: Keep the temperature and humidity sensors clean and free from dust or debris. Avoid bending or damaging the sensor cables.
- Ventilation: Ensure the controller's ventilation openings are not obstructed to prevent overheating.
- Opbevaring: When not in use for extended periods, store the controller in a cool, dry place away from direct sunlight and extreme temperatures.
9. Fejlfinding
If you encounter issues with your XM-18D controller, refer to the following common problems and solutions:
| Problem | Mulig årsag og løsning |
|---|---|
| Controlleren tænder ikke. |
|
| Temperature/Humidity readings are inaccurate. |
|
| Heater/Humidifier/Fan not activating. |
|
| Egg turning not working. |
|
| Alarm continuously sounds. |
|
10. Garanti og support
This product is manufactured to high-quality standards. For warranty information or technical support, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.
