Indledning
Thank you for choosing the Hyuduo Smart Bidet Attachment. This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your new bidet attachment. Please read this manual thoroughly before installation and use to ensure proper function and longevity of the product.
Produktkomponenter
Før installationen påbegyndes, skal du sørge for, at alle komponenter er til stede:
- 1 x Bidet Toilet Attachment
- 1 x Tee Joint (with 1 washer)
- 1 x White Pipe
- 2 x Large Washers
- 1 x engelsk brugsanvisning
Note: Please allow for minor discrepancies due to manual measurement.
Opsætning og installation
Follow these steps to properly install your Hyuduo Smart Bidet Attachment:
- Sluk for vandforsyningen: Locate the water supply valve for your toilet and turn it off completely. Flush the toilet to drain the tank.
- Fjern toiletsæde: Lift the toilet seat and lid. Unscrew the bolts holding the toilet seat to the toilet bowl. Keep these bolts and nuts as they will be reused.
- Position Bidet Attachment: Place the bidet attachment on the toilet bowl, aligning its adjustable brackets with the bolt holes. Adjust the brackets as needed to ensure a secure fit.
- Genmonter toiletsædet: Place your toilet seat back on top of the bidet attachment and the toilet bowl. Secure it using the original bolts and nuts. Ensure the bidet attachment is firmly held in place.
Image: The Hyuduo bidet attachment shown installed beneath a standard toilet seat on a toilet bowl.
- Disconnect Toilet Supply Hose: Disconnect the flexible water supply hose from the toilet tank's fill valve. Have a towel ready to catch any residual water.
- Install Tee Joint: Connect the provided Tee Joint to the toilet tank's fill valve. Ensure the washer is correctly seated to prevent leaks.
- Tilslut vandforsyning: Reconnect the flexible water supply hose to the bottom of the Tee Joint.
- Connect Bidet Hose: Connect one end of the white pipe (bidet hose) to the open port of the Tee Joint. Connect the other end of the white pipe to the water inlet on the bidet attachment. Use the large washers as needed to ensure a tight, leak-free connection.
- Genopret vandforsyningen: Slowly turn the main water supply valve back on. Check all connections for leaks. If leaks occur, tighten the connections.
Billede: Et nærbillede view of the bidet attachment's control panel, showing the water pressure dial.
Betjeningsvejledning
The Hyuduo Smart Bidet Attachment is designed for ease of use:
- Adjust Water Pressure: Use the control dial located on the side of the bidet attachment to adjust the water pressure. Turn the dial from 'OFF' towards 'LOW' for a gentle spray, and further towards 'HIGH' for a stronger spray.
- Dyseposition: The bidet features an intelligent flushing device that automatically positions the nozzle for effective cleaning.
- Selvrensende funktion: The nozzle has a self-cleaning function. After each use, the nozzle automatically rinses itself to maintain hygiene.
Billede: Et overheadbillede view of the Hyuduo bidet attachment, highlighting its slim design and control knob.
Opretholdelse
Regular maintenance ensures optimal performance and hygiene:
- Rengøring af dyse: The bidet attachment includes an automatic self-cleaning function for the nozzle. For additional cleaning, you may gently wipe the nozzle with a soft cloth and mild soap solution when the water supply is off.
- Udvendig rengøring: Clean the exterior of the bidet attachment with a soft, damp cloth and a mild, non-abrasive cleaner. Avoid harsh chemicals or abrasive pads that could damage the finish.
- Periodisk eftersyn: Kontrollér regelmæssigt alle vandtilslutninger for tegn på lækager eller slid. Spænd tilslutningerne efter behov.
Fejlfinding
If you encounter issues with your bidet attachment, refer to the following common problems and solutions:
| Problem | Mulig årsag | Løsning |
|---|---|---|
| No water spray or low pressure | Water supply valve is closed; hose kinked; clogged nozzle. | Ensure water supply valve is fully open. Check for kinks in the water hose. Gently clean the nozzle if visible debris is present. |
| Vandlækage fra tilslutninger | Loose connections; missing or improperly seated washers. | Turn off water supply. Tighten all connections. Ensure washers are correctly installed and not damaged. Replace washers if necessary. |
| Nozzle does not extend or retract properly | Debris obstructing nozzle; internal mechanism issue. | Turn off water supply. Gently inspect the nozzle area for any obstructions and remove them. If the problem persists, contact customer support. |
Specifikationer
- Varetype: Bidet Toilet Vedhæftet fil
- Materiale: ABS
- Bruttovægt: 850 g / 30.0 oz
- Pakkedimensioner: 18.11 x 7.87 x 3.15 tommer
- Modelnummer: Hyuduofcu7yo5thb-12
- Forbindelsesstørrelse: 3/8 tomme
Garanti og support
For warranty information or technical support, please refer to the documentation included with your purchase or contact the retailer where the product was acquired. You may also visit the official Hyuduo webwebsted for yderligere hjælp.