Indledning
This manual provides detailed instructions for the installation, operation, and maintenance of the WEIYINGSI 24V 250W Motor Speed Controller. This controller is designed for use with electric scooters, e-bikes, bicycles, and tricycles equipped with a 24V 250W DC brushed motor. Please read these instructions carefully before installation and use to ensure proper function and safety.
The WEIYINGSI 24V 250W Motor Speed Controller, a compact control unit for electric vehicles.
Sikkerhedsoplysninger
- Afbryd altid strømmen, før du udfører installation, vedligeholdelse eller fejlfinding.
- Sørg for, at alle forbindelser er sikre og korrekt polariserede for at forhindre beskadigelse af controlleren eller andre komponenter.
- Undgå at udsætte controlleren for vand, overdreven fugtighed eller ekstreme temperaturer.
- Forsøg ikke at åbne eller ændre controlleren casing, as this may void the warranty and pose a safety risk.
- Kontakt en kvalificeret tekniker, hvis du er usikker på nogen af installationstrinnene.
Opsætning og installation
Refer to the wiring diagram below for correct connection of the controller to your electric vehicle components. Ensure all connections match the specified colors and functions.
Detailed wiring diagram illustrating connections for battery, motor, throttle, key switch, brake switch, brake light, and indicator.
Ledningsforbindelser:
- Batteriforbindelse: Connect the battery wires to the corresponding terminals on the controller. Typically, red is positive (+) and black is negative (-).
- Motorforbindelse: Connect the motor wires (blue + and white -) to the motor output terminals.
- Throttle (Speed Governor): Connect the throttle unit. This typically uses a 1-4V signal for speed control.
- Nøglekontakt: Connect the key switch wires. Vigtig: The two wires of the key switch connector must be connected together (jumped) for the unit to power on and function.
- Bremsekontakt: Connect the brake switch wires. When activated, this switch cuts power to the motor.
- Bremselys: Connect the brake light wires (small red, small black) to the brake light connector.
- Indikator: Connect the indicator wires (small red, small black) for status display.
- Opladningsport: Connect the charging port if applicable.
Ensure all connectors are fully seated and secure. The controller features rubber grommets for wire protection and a rugged aluminum housing for durability and heat dissipation.
Image showing the physical dimensions of the controller: approximately 2.87 inches (73mm) length, 1.97 inches (50mm) width, and 1.38 inches (35mm) height.
Betjeningsvejledning
Når controlleren er korrekt installeret, og alle forbindelser er sikre:
- Ensure the key switch is in the 'ON' position (or the wires are jumped as per installation).
- Tilfør strøm til systemet.
- Use the throttle (speed governor) to control the motor speed. The throttle typically operates within a 1-4V range.
- Engage the brake switch to cut power to the motor and activate the brake light.
Opretholdelse
- Hold controlleren ren og fri for støv og snavs.
- Kontrollér regelmæssigt alle ledningsforbindelser for tæthed og tegn på slid eller korrosion.
- Ensure the controller's aluminum housing is not obstructed to allow for proper heat dissipation.
- Undgå at bruge skrappe kemikalier eller slibende materialer til rengøring.
Fejlfinding
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Controlleren tænder ikke. | Key switch not connected or jumped; battery low or disconnected. | Ensure key switch wires are connected or jumped. Check battery charge and connections. |
| Intermittent motor operation. | Loose or poor quality wiring connectors. | Inspect all connectors for secure fit. Consider soldering connections if issues persist. |
| Motoren reagerer ikke på gashåndtaget. | Throttle wiring incorrect or faulty; motor wiring incorrect. | Verify throttle connections and functionality. Check motor wiring polarity. |
| Motor runs but no speed control. | Throttle faulty or incorrectly connected. | Check throttle unit and its wiring to the controller. |
Specifikationer
The product label displaying key electrical specifications.
| Feature | Detalje |
|---|---|
| Mærke | WEIYINGSI |
| Modelnavn | CT01 (LB27) |
| Arbejde bindtage | 24 Volts (DC24V) |
| Nominel motoreffekt | 250 watt |
| Matching Motor | DC børstet motor |
| Under bindtage Beskyttelse | 20V±0.5V |
| Nominel strøm | 21±1A |
| Speed Governor (Throttle) | 1-4 volt |
| Materiale | Plastic (housing is aluminum) |
| Varens vægt | 4.1 ounce |
| Pakkedimensioner | 6.14 x 3.5 x 1.97 tommer |
Garanti
This product is covered by a standard manufacturer's warranty against defects in materials and workmanship. For specific warranty terms and conditions, please refer to the product packaging or contact the seller directly. Misuse, unauthorized modifications, or improper installation may void the warranty.
Støtte
If you encounter any issues or have questions regarding the WEIYINGSI 24V 250W Motor Speed Controller that are not addressed in this manual, please contact the seller or manufacturer for assistance. Provide your product model number (CT01) and a detailed description of the issue for faster support.
