LEDONE 8FT LED Vapor Tight Light Instruction Manual

1. Introduktion

This manual provides detailed instructions for the safe installation, operation, and maintenance of your LEDONE 8FT LED Vapor Tight Light. Please read this manual thoroughly before installation and retain it for future reference. This fixture is designed for demanding environments requiring high resistance to water, dust, and corrosion, such as parking garages, car washes, cold storage, and industrial facilities.

2. Sikkerhedsoplysninger

ADVARSEL: Risiko for elektrisk stød. Afbryd strømmen før installation eller service.

• Installation must be performed by a qualified electrician in accordance with the National Electrical Code (NEC) and local codes.
• Sørg for, at forsyningen voltage is compatible with the fixture's requirements (120-277Vac).
• Håndter ikke strømførende armaturer med våde hænder eller mens du står på våde eller våde steder.amp overflader.
• Forsøg ikke at ændre eller adskille armaturet. Der er ingen dele indeni, som kan serviceres af brugeren.
• Brug passende personlige værnemidler (PPE) under installationen.
• Sørg for, at armaturet er sikkert monteret for at forhindre det i at falde ned.

3. Pakkens indhold

Kontroller, at alle komponenter er til stede og ubeskadigede, før du fortsætter med installationen.

• LEDONE 8FT LED Vapor Tight Light Fixture
• Mounting Hardware (clips, screws, anchors)
• Instruktionsmanual (dette dokument)

4. Opsætning og installation

4.1. Forinstallation

1. Sluk for strømmen: Locate the circuit breaker or fuse box and turn off the power supply to the installation area. Verify power is off using a voltage tester.
2. Pakker ud: Carefully remove the fixture from its packaging. Inspect for any shipping damage.
3. Vælg Wattage and Color Temperature (CCT): Before mounting, adjust the wattage and CCT switches located on the fixture. These switches allow you to select between 60W, 80W, or 100W and 3500K, 4000K, or 5000K. Make your selection based on your lighting requirements.

Image: Product dimensions and location of wattage/CCT selection switches.

4.2. Montering af armaturet

The fixture is designed for surface mounting. Use the provided mounting clips and hardware.

1. Mark the desired mounting locations on the ceiling or wall. Ensure the marks are level and spaced appropriately for the fixture's length.
2. Bor forboringshuller på de markerede steder. Indsæt vægankre, hvis det monteres i gipsvæg eller murværk.
3. Secure the mounting clips to the surface using the provided screws.
4. Snap the LED vapor tight fixture into the mounted clips, ensuring it is firmly seated.

Billede: Eksample of surface mounting in a facility.

Image: Detail of the linkable design feature.

4.3. Elektriske ledninger

This fixture supports 0-10V dimming. Follow the wiring diagram below and local electrical codes.

• Tilslut Sort ledningen fra armaturet til Linje (L) ledningen fra strømforsyningen.
• Tilslut Hvid ledningen fra armaturet til Neutral (N) ledningen fra strømforsyningen.
• Tilslut Grøn ledningen fra armaturet til Jord (GND) ledningen fra strømforsyningen.
• For 0-10V dimming: Connect the Lilla ledningen fra armaturet til Dæmp+ wire from the 0-10V dimmer. Connect the Pink/Grå ledningen fra armaturet til Svag wire from the 0-10V dimmer.
• Ensure all connections are secure using appropriate wire connectors.

Note: If 0-10V dimming is not used, cap the purple and pink/gray wires individually with wire nuts.

5. Betjeningsvejledning

1. Tænd: Once installation and wiring are complete, restore power to the circuit at the breaker or fuse box. The fixture should illuminate.
2. Dæmpning: If connected to a compatible 0-10V dimmer, adjust the dimmer control to achieve the desired light output level.
3. Wattage and CCT Adjustment: Wattage and CCT are set via internal switches during installation. These are not typically adjusted during normal operation. If changes are needed, disconnect power before accessing the switches.

6. Vedligeholdelse

The LEDONE Vapor Tight Light is designed for long-term, low-maintenance operation. Regular cleaning can help maintain optimal light output.

• Rensning: Afbryd strømmen før rengøring. Brug en blød, tør klud.amp cloth with a mild, non-abrasive cleaner to wipe the exterior of the fixture. Do not use harsh chemicals or abrasive pads, as these can damage the finish or lens.
• Inspektion: Periodically inspect the fixture and mounting hardware for any signs of damage, loose connections, or wear. Address any issues promptly.
• Ingen dele, der kan serviceres af brugeren: The LED light source and driver are integrated components. Do not attempt to open or repair the fixture. Contact qualified personnel for any issues beyond basic cleaning and inspection.

Image: The IP65 waterproof rating ensures durability in wet conditions.

7. Fejlfinding

Before performing any troubleshooting, ensure power is disconnected at the circuit breaker.

8. Specifikationer

Image: Key features and certifications of the LEDONE Vapor Tight Light.

9. Garantioplysninger

LEDONE products are manufactured to high quality standards. This product comes with a standard manufacturer's warranty. Please refer to the product packaging or the official LEDONE webwebstedet for specifikke garantivilkår og -betingelser. Gem din købsbevis til garantikrav.

10. Kundesupport

If you have any questions, require technical assistance, or need to report an issue, please contact LEDONE customer support:

• Webwebsted: Visit the LEDONE Store on Amazon (for general inquiries)
• E-mail: Se produktemballagen eller den officielle webwebsted for direkte support-e-mail.
• Telefon: Se produktemballagen eller den officielle webwebsted for direkte supporttelefonnummer.

Please have your product model number (8FT LED Vapor Tight Light) and proof of purchase ready when contacting support.