1. Sikkerhedsoplysninger
ADVARSEL: To avoid fire, shock, or death, turn off power at the circuit breaker or fuse box and test that power is off before wiring. Installation should be performed by a qualified electrician or a person with electrical experience. Read all instructions before installation.
- Do not use with electronic ballasts.
- Sørg for det samlede wattage of connected lights does not exceed the switch's maximum rating.
- Kun til indendørs brug.
2. Produktet er slutview
The TOPGREENER TDOS5-KM-I is a Passive Infrared (PIR) motion sensor switch designed to automatically control lighting based on occupancy or vacancy in a room. It features adjustable settings for motion detection sensitivity and time delay, offering flexible control for various applications.
Nøglefunktioner:
- PIR Motion Detection with 180° field of view.
- Occupancy (Auto ON, Auto OFF) and Vacancy (Manual ON, Auto OFF) modes.
- Der kræves ingen neutral ledning.
- Operable without a ground wire connection (ground wire connection is recommended for safety).
- Compatible with dimmable LED light bulbs (minimum 15W load).
- Adjustable time delay (15 sec, 5 min, 10 min, 20 min, 30 min).
- Adjustable motion detection sensitivity (Range).
3. Installation
3.1 Trin før installation
- Sluk for strømmen: Locate the circuit breaker or fuse that supplies power to the switch location and turn it OFF. Verify power is off using a voltage tester.
- Fjern den gamle switch: Fjern forsigtigt den eksisterende vægplade og afbryderen fra vægdåsen. Frakobl ledningerne fra den gamle afbryder.
3.2 Ledningsinstruktioner
The TDOS5-KM-I features a universal wiring design, allowing for interchangeable hot and load wires, simplifying installation. A neutral wire is not required. While operable without a ground wire, connecting the ground wire is highly recommended for safety.
- Identificér ledninger: In your wall box, identify the hot (line) wire and the load wire.
- Tilslut ledninger: Connect the hot wire to one of the switch's terminals and the load wire to the other terminal. The switch's design allows these to be interchangeable.
- Ground Wire (Recommended): If a ground wire is present in your wall box, connect it to the green ground screw on the switch.
- Sikre ledninger: Sørg for, at alle ledningsforbindelser er sikre.
3.3 Kompatibilitet og vigtige bemærkninger
- Denne kontakt er ONLY compatible with dimmable LED light bulbs.
- Det er det INCOMPATIBLE with any lighting that includes electronic ballasts.
- The switch's circuit requires a minimum load of 15W.
3.4 Efterinstallation
- Monter afbryder: Carefully push the wired switch into the wall box and secure it with screws.
- Fastgør vægplade: Install the decorative wall plate.
- Gendan strøm: Tænd for strømmen igen ved afbryderen.
- Opvarmningstid: Allow 1-2 minutes for the device to warm up after installation before testing its functionality.
4. Betjening
The TDOS5-KM-I offers two operational modes: Occupancy and Vacancy, along with adjustable settings for motion detection range and time delay.
4.1 driftstilstande
- Occupancy Mode (Auto ON, Auto OFF): In this mode, the lights will automatically turn ON when motion is detected and turn OFF after a set time delay when no motion is detected.
- Vacancy Mode (Manual ON, Auto OFF): In this mode, the lights must be manually turned ON by pressing the switch button. They will then automatically turn OFF after a set time delay when no motion is detected.
4.2 Ændring af tilstande
To switch between Occupancy and Vacancy modes, locate the ON/OFF push button on the face of the device. Press and hold this button for 3 seconds. The mode will toggle between Occupancy and Vacancy.
4.3 justerbare indstillinger
The switch features two adjustable dials located under the faceplate for customizing its performance:
- Rækkevidde: This dial controls the motion detection sensitivity. Adjust it according to the daylight conditions and the size of the room to optimize detection. Settings typically range from 1 (lowest sensitivity) to 4 (highest sensitivity).
- Tid: This dial determines how long the light will remain ON after the last detected motion. Available options include: 15 seconds (Test mode), 5 minutes, 10 minutes, 20 minutes, and 30 minutes.
5. Vedligeholdelse
The TOPGREENER TDOS5-KM-I Motion Sensor Switch requires minimal maintenance. To ensure optimal performance and longevity:
- Rensning: Periodically wipe the surface of the switch and sensor lens with a soft, dry cloth. Avoid using abrasive cleaners, solvents, or excessive moisture, as these can damage the device.
- Forhindringer: Ensure the sensor lens is not obstructed by furniture, decorations, or other objects that could block its field of view, affecting motion detection.
6. Fejlfinding
If you experience issues with your TOPGREENER TDOS5-KM-I Motion Sensor Switch, refer to the following common problems and solutions:
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Lysene tændes ikke automatisk. |
|
|
| Lysene slukker ikke. |
|
|
| Sensor is overly sensitive or not sensitive enough. |
|
|
7. Specifikationer
- Model: TDOS5-KM-I
- Input bindtage: 120VAC, 60Hz
- Nuværende vurdering: 1.25A
- Belastningskompatibilitet: 300W Tungsten, 150W Dimmable LED
- Mindste belastning: 15W
- Sensortype: Passiv infrarød (PIR)
- Felt af View: 180 grader
- Maks. dækningsområde: 1200 kvadratmeter
- Driftstilstande: Occupancy (Auto ON/OFF), Vacancy (Manual ON/Auto OFF)
- Time Delay Options: 15 sec (Test), 5 min, 10 min, 20 min, 30 min
- Driftstemperatur: 32-104°F (0-40°C)
- Dimensioner: 2.5" W x 4.5" H x 2.5" D (Device)
- Certificeringer: UL-godkendt, overholder Title 20 & Title 24
- Ledningsføring: Single-pole only, no neutral wire required, operable without ground wire (ground recommended).
8. Garanti og support
For warranty information or technical support, please contact TOPGREENER customer service. Refer to the product packaging or the official TOPGREENER webwebstedet for de seneste kontaktoplysninger og garantivilkår.
Webwebsted: www.topgreener.com