Akicon Ultra Quiet Bathroom Exhaust Fan with LED Light

1. Sikkerhedsoplysninger

Read and understand all instructions before beginning installation. Failure to follow these instructions may result in electric shock, fire, property damage, or personal injury.

• Afbryd altid strømmen på servicepanelet, før du tilslutter eller servicerer enheden.
• Al ledningsføring skal overholde lokale elektriske forskrifter og standarder.
• Denne enhed er kun beregnet til generel ventilation. Må ikke anvendes til udsugning af farlige eller eksplosive materialer og dampe.
• To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device unless specifically approved for such use.
• Ensure the installation location provides adequate structural support for the fan.

2. Pakkens indhold

Kontroller, at alle komponenter er til stede, før installationen påbegyndes:

• Ventilatorhus
• Grille samling
• LED Bulbs (2x)
• Frosted Glass Cover
• Monteringsskruer
• Instruktionsmanual

Image: Components of the Akicon Bathroom Exhaust Fan.

3. Produktspecifikationer

Image: Key dimensions of the Akicon Bathroom Exhaust Fan.

Image: Detailed housing dimensions and ceiling opening size requirements.

4. Installation

This fan can be installed with or without attic access. Refer to the appropriate video and steps below.

4.1 Kontrol før installation

• Ensure your soffit or attic has enough space for installation.
• Required opening size: 8-1/2" x 8-5/16".
• Soffit/Attic Height: > 6-1/2".

Image: Pre-installation considerations for attic and soffit space.

4.2 Installation with Attic Access

1. Starting next to a joist, trace an outline for the fan housing.
2. Use a drywall saw to cut the marked opening.
3. Slide the fan housing into the opening and screw it into the joist.
4. Attach the duct to the fan's exhaust port and apply HVAC tape over the connection to ensure a secure seal.
5. Connect the house wires to the fan wires (black to black, white to white, ground to ground).
6. Place insulation over and around the fan housing.
7. Plug in the light connection.
8. Install the grille, LED bulbs, and glass cover.

4.3 Installation without Attic Access (No-Attic Installation)

1. If attic access is not available, this model allows for no-attic installation.
2. First, disconnect the wires connecting the motor and the housing.
3. Remove the fixing screws on the outside of the housing. This allows you to remove the motor from the housing.
4. After connecting the ventilation duct, send the housing into the ceiling opening.
5. Connect the wires correctly according to the label on the wires (black to black, white to white, ground to ground).
6. Secure the housing to the joist using appropriate fasteners.
7. Reinstall the motor back into the housing and connect the plugs.
8. Finally, install the grille, LED bulbs, and glass cover.

4.4 Ledningsdiagram

Image: Electrical wiring diagram for connecting the fan and light to a switch.

5. Betjeningsvejledning

The Akicon BPT14-80CL fan is designed for efficient and quiet operation.

5.1 Ventilatordrift

• The fan operates at 80 CFM (Cubic Feet Per Minute) with a noise level of 2.0 Sones, ensuring effective ventilation with minimal sound.
• Activate the fan using the connected wall switch.

5.2 LED-lysets betjening

• The integrated LED light offers three color temperature options: 3000K (Warm White), 4000K (Cool White), and 5000K (Daylight).
• To select your desired color temperature, locate the sliding switch on the back of the lampshade (or on the LED bulbs themselves, depending on the specific bulb type). Adjust this switch before installing the glass cover.
• The LED light is dimmable, allowing you to adjust brightness using a compatible dimmer switch (sold separately).

Billede: Overview of the fan's performance and lighting features.

6. Vedligeholdelse

Regelmæssig vedligeholdelse sikrer optimal ydeevne og levetid for din udsugningsventilator.

6.1 Cleaning the Grille and Glass Cover

• Disconnect power at the service panel before cleaning.
• Carefully remove the glass cover by rotating it counter-clockwise.
• Wash the glass cover with mild soap and water, then dry thoroughly.
• Wipe the grille with a damp klæde. Brug ikke slibende rengøringsmidler.
• Reinstall the glass cover by aligning the markings and rotating clockwise until secure.

6.2 Replacing LED Bulbs

• Afbryd strømmen på servicepanelet.
• Remove the glass cover as described above.
• Unscrew the old LED bulbs and replace them with new ones of the same type (GU24 base, if applicable, or compatible LED bulbs).
• Reinstall the glass cover.

7. Fejlfinding

If your fan is not operating correctly, consult the following common issues:

8. Garanti og support

This Akicon Bathroom Exhaust Fan comes with a 3-Year Limited Warranty, ensuring confidence in the quality and construction of the product.

8.1 Kundesupport

Ved spørgsmål, problemer eller manglende dele, kontakt venligst Akicon kundeservice:

• Servicetider: 8 – 6 EST, mandag-fredag
• Telefon: +1 (302) 213-4406
• E-mail: service@akiconshop.com