QINIZX DC 12V 24V 4A 2-vejs justerbar PWM ventilatorhastighedsregulator brugsanvisning

1. Produktet er slutview

The QINIZX DC 12V 24V 4A 2-Way Adjustable PWM Fan Speed Controller utilizes PWM control technology to regulate fan speed based on ambient temperature. This controller automatically adjusts fan speed; higher temperatures result in faster fan operation. When the ambient temperature falls below a pre-set starting temperature, the controller stops the fan. It supports various DC 12V/24V 2-wire, 3-wire, or 4-wire fans or motors with a maximum drive current of 4A.

2. Nøglefunktioner

• PWM Control Technology: Enables temperature-controlled fan speed regulation.
• Dobbelte arbejdstilstande: Offers both Fixed temperature range and Adjustable temperature modes.
• Bred kompatibilitet: Supports DC 12V/24V 2-wire, 3-wire, and 4-wire fans/motors.
• High Drive Current: Maximum drive current of 4A.
• Power Supply Reverse Protection: Protects the controller and fan from damage due to incorrect polarity.
• Dynamic LED Indicators: Provides visual feedback on the controller's operational status.
• Kompakt design: Small form factor (2.20x1.38x0.79 inches) with M3 mounting holes for space-saving installation.
• Højpræcisions temperatursensor: Includes a 30cm (11.8-inch) cable and mounting buckle, capable of measuring air, liquid, and solid surface temperatures from -20°C to 110°C with ±1°C accuracy.

3. Pakkens indhold

• 1x PWM Fan Speed Controller (PCBA)
• 1x Temperature Sensor with Cable

4. Opsætningsvejledning

Follow these steps to correctly install and connect your fan speed controller:

1. Forbered komponenter: Ensure you have the controller, temperature sensor, DC fans, and a compatible DC power supply.
2. Tilslut temperatursensor: Plug the temperature sensor cable into the designated white connector on the controller board. Secure the sensor to the area where temperature monitoring is required.
3. Tilslut ventilatorer: Connect your DC fans to the fan output terminals (F1+, F1-, F2+, F2-) on the controller. The controller supports up to two fans directly. For multiple fans, connect them in parallel to the fan wiring port. Ensure the total current of all connected fans does not exceed the controller's rated current (4A).
   
   

   Figure 4.1: Wiring diagram for connecting the controller, power supply, and fans.

   
   

   Figure 4.2: Close-up of the controller board showing input and output terminals.
4. Tilslut strømforsyning: Connect a DC power supply to the VIN+ and VIN- terminals. Vigtig: Voltage of the DC power supply must match the rated voltage of the connected fans (12V or 24V). The current of the power supply must be greater than the total current drawn by all connected fans.
   
   

   Figure 4.3: The QINIZX PWM Fan Speed Controller with its connected temperature sensor.

5. Bekræft forbindelser: Double-check all wiring to ensure correct polarity and secure connections before applying power.

Demonstrationsvideo af opsætning

Video 4.1: A demonstration of connecting and operating a PWM fan controller. This video illustrates the physical connections and basic functionality.

Video 4.2: Another demonstration showcasing the setup and control of a fan speed controller. This video provides additional visual guidance for installation.

5. Betjeningsvejledning

The controller offers two operational modes: Fixed Temperature Mode and Adjustable Temperature Mode. A small switch on the board allows you to select between these modes.

5.1 Valg af tilstand

Figur 5.1: Detaljeret view of the controller board highlighting the mode selection switch and the adjustable potentiometer.

• Fixed Temperature Mode (F): In this mode, the starting temperature for fan operation is fixed at 30°C (86°F). The fan speed will linearly increase as the temperature rises from 30°C to 50°C. Above 50°C (122°F), the fan will operate at full speed. The potentiometer is inactive in this mode.
• Adjustable Temperature Mode (A): This mode allows you to set the starting temperature using the rotary potentiometer. The adjustable start-up temperature range is 10°C to 50°C. The fan will reach full speed when the temperature is 20°C above the set starting temperature (Full-speed temperature = Starting temperature + 20°C).

5.2 Temperaturhysterese

The controller incorporates a hysteresis circuit. The fan's start and stop temperatures are separated by a 2°C difference. For example, if the set start temperature is 30°C, the fan will stop when the temperature drops below 28°C. After stopping, the fan will not restart until the temperature rises to 30°C or higher.

5.3 Fan Speed Curve

Figure 5.2: Graph showing the relationship between temperature and fan speed/air volume. 'L' represents the start temperature, and 'H' represents the full-speed temperature (L+20°C).

6. Vedligeholdelse

To ensure optimal performance and longevity of your QINIZX fan speed controller, consider the following maintenance guidelines:

• Hold rent: Periodically inspect the board for dust accumulation. Use a soft, dry brush or compressed air to gently clean the components.
• Sørg for korrekt ventilation: Do not obstruct the airflow around the controller, especially if it's installed in an enclosed space.
• Tjek forbindelser: Regularly verify that all wire connections are secure and free from corrosion.
• Undgå fugt: Protect the controller from moisture and extreme humidity, which can damage electronic components.
• Temperature Sensor Placement: Ensure the temperature sensor remains securely placed in the desired monitoring location and is not damaged.

7. Fejlfinding

If you encounter issues with your fan speed controller, refer to the following common problems and solutions:

• Ventilator starter ikke:
  • Bekræft strømforsyningen voltage matches the fan's rated voltage.
  • Ensure the power supply current is sufficient for all connected fans.
  • Check if the ambient temperature is below the set starting temperature (considering the 2°C hysteresis).
  • Confirm all fan connections are secure and correctly wired.
  • Inspect the temperature sensor for damage or improper connection.
• Fan Running at Incorrect Speed:
  • In Adjustable Mode, ensure the potentiometer is set to the desired starting temperature.
  • Verify the mode selection switch is in the correct position (Fixed or Adjustable).
  • Check the temperature sensor's placement and ensure it is accurately reading the ambient temperature.
• LED-indikatorer fungerer ikke:
  • Confirm the power supply is connected and providing the correct voltage.
  • Check for any visible damage to the controller board.
• Overophedning af controller:
  • Ensure the total current of connected fans does not exceed the 4A maximum.
  • Provide adequate ventilation around the controller.

8. Tekniske specifikationer

Figure 8.1: Physical dimensions of the controller board.

Figure 8.2: Details and dimensions of the included temperature sensor.

9. Vigtige sikkerhedsoplysninger

• Always ensure the power supply is disconnected before making or changing any connections.
• Bekræft korrekt voltage and current ratings for all components to prevent damage.
• Do not expose the controller to water, excessive heat, or corrosive environments.
• Handle electronic components with care to avoid electrostatic discharge.
• Opbevares utilgængeligt for børn.

10. Garanti og support

For warranty information and technical support, please refer to the documentation provided with your purchase or contact QINIZX customer service directly. Details are typically available on the manufacturer's official webhjemmeside eller gennem din forhandler.