PEMP AHD Backup Camera User Manual

1. Produktet er slutview

The PEMP AHD Backup Camera is designed to provide a clear rear view for parking and reversing maneuvers. This camera offers 720P resolution at 25 frames per second, ensuring high-definition video quality. It is specifically designed for select BMW models and requires a compatible display unit.

Nøglefunktioner:

• HD AHD camera with maximum 1920x720 resolution.
• Camera width up to 120 degrees for a wide field of view.
• HD night vision effect for improved visibility in low-light conditions.
• Designed for specific BMW models: F10, F30, F25, F48.

Vigtige kompatibilitetsnoter:

• Dette kamera er not suitable for your original car display if it does not support an AHD input interface. It only supports rear displays with AHD input.
• Your display must support 720P 25FPS format input; otherwise, the image will be black and white.
• This camera is only suitable for BMW F10, F30, F25, F48 dedicated rear-view camera installations. It is not compatible with other models.

2. Produktspecifikationer

3. Installationsvejledning

3.1 Forberedelse

1. Remove the fixing screws on the sound insulation board of the trunk.
2. Remove the warning sign hanger.
3. Remove the protective cover on the luggage compartment support rod.
4. Remove the entire boot sound insulation panel.
5. Remove the trunk handle from the original vehicle.

Image: A person removing screws from the trunk's sound insulation board.

Image: A person using a tool to remove the original trunk handle.

3.2 Kameramontering

6. Remove the rear cover from the trunk handle and install it to the camera assembly.
7. Install the camera to the original position of the trunk handle.

Image: Detailed dimensions of the PEMP AHD Backup Camera, showing 160mm length and 46mm width.

3.3 Kabelføring

8. Hide the camera line in the slot in the trunk.
9. Pass the wire through the trunk support lever and install the protective cover.
10. The line of the camera can be hidden along the rubber strip of the window.
11. Put the back seat down and lead the camera cable to the trunk.

3.4 Ledningsforbindelser

Connect the wires according to the instructions provided in the video and diagram. Ensure proper connection of the video input and power lines.

Image: A detailed wiring diagram showing connections for the rear camera to the display unit and power source.

3.5 Genmontering

12. Tie up any excess wire with a tie and fix it securely in the trunk.
13. Install the sound insulation board and warning board of the trunk.

3.6 Installationsvideoguide

Video: Detailed installation guide for the PEMP AHD Backup Camera on a BMW F30 model.

4. Opsætning og konfiguration

4.1 Camera Type and Format Selection

1. Access the settings menu on your display unit.
2. Naviger til Car Settings > Reversing Settings > Camera Type.
3. Vælge Aftermarket Camera.
4. Under Camera Format (For Aftermarket Camera), choose the correct format for your camera. For this AHD 720P camera, select AHD 720p@25.
5. After making the selection, turn off the engine and restart the vehicle for changes to take effect.

4.2 foran-view Camera Settings (if applicable)

If you have a front-view camera installed, ensure its settings are correctly configured.

• After the camera is connected, go to Settings > Car Settings > Reverse Settings og indstil Foran-view Tid to a non-zero value. The front-view time can be set according to your needs, but it cannot be set to 0, otherwise the front view vil ikke blive vist.

4.3 Manual Transmission Settings

For models with manual transmission, the reverse image can be displayed normally only when the gear type is set to 2 or 3.

Image: Screenshot showing the 'Gear Selection' option in Factory Settings for manual transmission vehicles.

4.4 Opsætningsvideoguide

Video: Demonstrates camera wiring and demo instructions, including screen settings for reverse camera display.

5. Fejlfinding

5.1 Reverse Screen Shows No Signal

If your Linux screen reversing does not show up or displays "No Signal", follow these steps:

1. Enter the original car interface. If the original car does not display, contact customer service.
2. Gå til Settings > Car Settings > Reversing Settings > Camera Type og vælg Aftermarket Camera.
3. Under Camera Format (For Aftermarket Camera), ensure you have selected the correct format (e.g., AHD 720p@25).
4. Turn off the engine and restart the vehicle.

5.2 Radar Button Not Responding

If your radar button doesn't respond, you can enable it through the settings:

1. Gå til Settings > Car Settings > Reversing Settings.
2. Tænd for Radar (For Aftermarket Camera) valgmulighed.

5.3 General Wiring Issues

For detailed wiring instructions and troubleshooting common connection problems, refer to the following video:

Video: Guide on how to connect and set up an AHD camera, addressing common wiring concerns.

6. Vedligeholdelse

To ensure optimal performance and longevity of your PEMP AHD Backup Camera, consider the following maintenance tips:

• Rengør kameralinsen regelmæssigt med en blød kludamp klud til at fjerne snavs, støv eller vandpletter, der kan blokere view.
• Inspect wiring connections periodically to ensure they are secure and free from corrosion or damage.
• Avoid using harsh chemicals or abrasive materials on the camera or its components.

7. Garanti og support

PEMP is committed to providing high-quality products and excellent customer service. For any inquiries or support needs, please refer to the following information:

• Kundeservice: We aim to respond to your messages within 24 hours with a professional after-sales team.
• Produktkvalitet: Product quality is our first priority. Please be assured of the product's reliability.
• Vehicle Fitment Questions: If you have doubts about vehicle fitment, please send us a photo of your car's dashboard and model year to avoid mistakes.