HOFTRONIC Esto 2-Light GU10 Black LED Spotlight

1. Introduktion

Thank you for choosing the HOFTRONIC Esto 2-Light GU10 Black LED Spotlight. This product is designed for indoor use, providing adjustable lighting with two GU10 LED bulbs. Constructed from high-quality aluminum, this spotlight offers a modern aesthetic and reliable performance. Please read this manual carefully before installation and use to ensure safe and optimal operation.

Image: The HOFTRONIC Esto 2-Light GU10 Black LED Spotlight installed on a ceiling, providing illumination in a modern interior setting.

2. Sikkerhedsinstruktioner

• Always disconnect the main power supply before attempting any installation, maintenance, or bulb replacement.
• Installation should be performed by a qualified electrician to ensure compliance with local electrical codes and safety standards.
• This product is rated IP20 and is suitable for kun indendørs brug. Do not expose to moisture or direct water.
• Sørg for, at voltage supply matches the product's requirements (230V AC).
• Overskrid ikke det maksimale wattage of 35 Watts per GU10 LED bulb.
• Sørg for tilstrækkelig ventilation omkring armaturet for at forhindre overophedning.
• Dæk ikke armaturet med isoleringsmateriale, medmindre det er specielt designet til det.

3. Indhold i kassen

Kontroller venligst, at alle komponenter er til stede og ubeskadigede, før du fortsætter installationen.

Image: Contents of the product box, including the spotlight fixture and mounting hardware.

• 1x HOFTRONIC Esto Double Black LED Ceiling Spot Fixture
• 1x unbrakonøgle
• 4 x skruer
• 4x skiver
• 4x vægstik

4. Opsætning og installation

Follow these steps for safe and correct installation of your LED spotlight.

1. Forbered til installation: Sørg for, at hovedstrømforsyningen til installationsområdet er afbrudt ved afbryderen.
2. Markér borepunkter: Position the fixture on the ceiling at the desired location. Use the mounting holes on the base of the fixture to mark the drilling points. Refer to the diagram below for mounting dimensions.


Image: Detailed diagram of the spotlight's base with mounting hole dimensions (69mm x 69mm spacing, 4mm diameter holes, 13mm edge distance, max 12mm cable inlet).

3. Bore huller: Bor huller på de markerede punkter. Sæt de medfølgende rawlplugs i de borede huller.
4. Tilslut ledninger: Open the terminal cover on the fixture. Carefully connect the electrical wires from your ceiling to the terminal block inside the fixture. Ensure correct connections: Live (L), Neutral (N), and Earth (⌀). The cable inlet supports a maximum diameter of 12mm.
5. Monter armaturet: Align the fixture's mounting holes with the wall plugs. Secure the fixture to the ceiling using the provided screws and washers. Do not overtighten.
6. Insert GU10 Bulbs: Insert two GU10 LED bulbs (not included) into the lamp holders. Ensure they are securely twisted into place. Do not exceed 35 Watts per bulb.
7. Gendan strøm: Once installation is complete and all connections are secure, restore the main power supply.

5. Betjeningsvejledning

The HOFTRONIC Esto spotlight is designed for simple operation.

• Tænd/sluk: Control the spotlight using your standard wall light switch.
• Juster lysets retning: The GU10 fittings are tiltable, allowing you to adjust the light direction by up to 30 degrees. Gently pivot the inner lamp holders to direct the light as desired.

Image: Illustration of the adjustable light direction, demonstrating the 30-degree tilt capability of the GU10 fittings.

6. Vedligeholdelse

Regular maintenance will help prolong the life and appearance of your spotlight.

• Rensning: Ensure the power is off and the fixture is cool before cleaning. Wipe the exterior of the spotlight with a soft, dry, or slightly damp klud. Brug ikke slibende rengøringsmidler, opløsningsmidler eller stærke kemikalier, da disse kan beskadige overfladen.
• Udskiftning af pære:
  1. Sluk for strømforsyningen til armaturet.
  2. Lad pæren køle helt af, hvis den har været i brug for nylig.
  3. Gently push the GU10 bulb into its fitting and twist it counter-clockwise to remove.
  4. Insert a new GU10 LED bulb (max 35W) by pushing it into the fitting and twisting clockwise until secure.
  5. Gendan strømmen.

7. Fejlfinding

Hvis du støder på problemer med din spotlight, kan du se følgende almindelige problemer og løsninger:

• Lyset tænder ikke:
  • Kontroller om hovedstrømforsyningen er tændt.
  • Ensure the wall switch is in the 'on' position.
  • Verify that the GU10 bulbs are correctly inserted and not faulty.
  • Inspect wiring connections for looseness or damage (ensure power is off before inspection).
• Lys flimrer:
  • Ensure GU10 bulbs are fully seated in their sockets.
  • Try replacing the bulb to rule out a faulty bulb.
  • Kontroller for løse ledningsforbindelser (med strømmen afbrudt).
• Fixture feels hot:
  • Confirm that the installed GU10 bulbs do not exceed the maximum wattage på 35W.
  • Ensure there is no obstruction preventing proper heat dissipation.

If problems persist, contact customer support or a qualified electrician.

8. Specifikationer

Image: Overall dimensions of the HOFTRONIC Esto 2-Light GU10 Black LED Spotlight.

9. Garanti

This HOFTRONIC product comes with a 3 års garanti, reflecting our commitment to quality and durable construction. The robust aluminum enclosure ensures a long lifespan for your ceiling light.

Image: Warranty information, indicating a 3-year warranty and durable build quality.

10. Support

For further assistance, technical support, or warranty claims, please contact your retailer or the HOFTRONIC customer service department. Refer to your purchase documentation for contact details.