MIPRO ACT-5802/ACT-58H2 Digital Wireless Microphone System User Manual

Indledning

This manual provides detailed instructions for the setup, operation, and maintenance of your MIPRO ACT-5802/ACT-58H2 Digital Wireless Microphone System. This system features a 5 GHz 1/2U dual-channel digital receiver and two ISM 5 GHz digital handheld wireless microphones, designed for reliable and high-quality audio transmission.

Hvad er der i æsken

Ved udpakning skal du kontrollere, at alle følgende komponenter er inkluderet:

• 1 x ACT-5802 Dual-Channel Digital Receiver
• 2 x ACT-58H2 Handheld Digital Wireless Microphones
• 1 x strømadapter til modtager
• 2 x antenner
• 1 x lydkabel
• 1 x brugermanual

Note: If any items are missing or damaged, please contact your dealer immediately.

Produkt overview

The MIPRO ACT-5802/ACT-58H2 system provides a robust wireless audio solution. Below is an image of the complete system.

Figur 1: MIPRO ACT-5802/ACT-58H2 Digital Wireless Microphone System. This image displays the ACT-5802 dual-channel receiver unit and two ACT-58H2 handheld microphones, illustrating the primary components of the wireless audio system.

Opsætningsinstruktioner

1. Receiver Setup (ACT-5802)

1. Placering: Position the receiver on a stable, flat surface, away from potential sources of interference such as Wi-Fi routers, microwave ovens, or other 5 GHz devices. Ensure adequate ventilation.
2. Antenneforbindelse: Connect the two supplied antennas to the ANTENNA A and ANTENNA B connectors on the rear panel of the receiver. Ensure they are securely tightened.
3. Strømtilslutning: Connect the power adapter to the DC IN jack on the rear panel of the receiver, then plug the adapter into an appropriate AC power outlet.
4. Lydudgangsforbindelse: Connect the receiver's audio output (XLR or 1/4" jack) to the input of your mixer, amplifier, or audio recording device using the supplied audio cable.

2. Handheld Microphone Setup (ACT-58H2)

1. Batteri installation: Unscrew the lower part of the microphone body to reveal the battery compartment. Insert two fresh AA batteries, observing the correct polarity (+/-) as indicated inside the compartment. Screw the lower part back on securely.
2. Tænd: Press and hold the power button on the microphone until the display illuminates.
3. Pairing (ACT Sync):
   • On the receiver, select the desired channel (e.g., Channel 1 or Channel 2) using the control buttons.
   • Press the "ACT" button on the receiver. The ACT indicator will flash.
   • Align the microphone's IR window with the receiver's IR window (usually located on the front panel) within 30 cm (1 foot).
   • The microphone will automatically sync with the receiver. Once synced, the receiver's ACT indicator will stop flashing, and the microphone's display will show the matched channel.

Betjeningsvejledning

1. Tænd/sluk

• Modtager: Press the power button on the front panel. The OLED display will illuminate.
• Mikrofon: Press and hold the power button until the display illuminates (on) or turns off (off).

2. Channel Selection and Adjustment

• The ACT-5802 receiver allows for automatic frequency scanning to find clear channels. Refer to the receiver's display and menu buttons for navigation.
• Once a clear channel is selected on the receiver, use the ACT Sync function (as described in Setup) to pair the microphone to the new channel.

3. Lydstyrkekontrol

• Receiver Output Level: Adjust the volume knob on the front panel of the ACT-5802 receiver to control the audio output level sent to your mixer or amplivligere.
• Mikrofonforstærkning: Some microphones may have internal gain adjustments. Consult the microphone's specific instructions if needed. Generally, start with a moderate gain setting.

4. Vis oplysninger

The OLED display on both the receiver and microphones provides critical information such as channel number, frequency, battery status, and RF/AF signal strength. Monitor these displays during operation for optimal performance.

Opretholdelse

1. Rensning

• Use a soft, dry cloth to clean the exterior surfaces of the receiver and microphones.
• Do not use liquid cleaners, solvents, or abrasive materials, as these can damage the finish or internal components.
• For microphone grilles, gently wipe with a slightly damp klud og sørg for, at den er helt tør før brug.

2. Batteripleje

• Always remove batteries from the microphones if they will not be used for an extended period to prevent leakage and damage.
• Replace batteries promptly when the low battery indicator appears on the microphone's display.
• Brug alkaliske batterier eller genopladelige AA-batterier af høj kvalitet.

3. Opbevaring

• Store the system in a cool, dry place, away from direct sunlight, extreme temperatures, and high humidity.
• Keep the original packaging for safe transport and storage.

Fejlfinding

Specifikationer

Garanti og support

For warranty information and technical support, please refer to the warranty card included with your product or visit the official MIPRO webwebsted. Gem din købskvittering som købsbevis i tilfælde af garantikrav.

For further assistance, contact your authorized MIPRO dealer or distributor.