1. Introduktion
This manual provides instructions for the GoolRC Flysky FS-i6X 2.4GHz 10CH RC Transmitter and FS-iA6B Receiver. This system utilizes AFHDS 2A technology, offering robust interference protection, low power consumption, and high receiver sensitivity. It supports data reception from various sensors and servo calibration, making it suitable for RC drones, airplanes, and helicopters.
Figure 1: GoolRC Flysky FS-i6X Transmitter and FS-iA6B Receiver.
2. Hvad er der i æsken
Pakken indeholder følgende komponenter:
- FS-i6X Remote Controller
- FS-iA6B Receiver
- Bind stik
- Manuel
Figure 2: Package contents including the FS-i6X transmitter, FS-iA6B receiver, bind plug, and manual.
3. Opsætning
3.1. Initial Setup and Binding
Follow these steps to set up your FS-i6X transmitter and bind it with the FS-iA6B receiver:
- Remove the FS-i6X transmitter from its packaging.
- Insert 4 AA batteries into the transmitter.
- Tænd for senderen.
- Connect the bind plug to the receiver's B/VCC port.
- Power on the receiver. The LED on the receiver should flash rapidly, indicating it is in binding mode.
- Tryk på og hold på senderen BIND KEY while powering it on. The transmitter display will show "Binding...".
- Once the binding is successful, the transmitter display will show "RX Bind OK" and the receiver's LED will turn solid.
- Remove the bind plug from the receiver. The receiver is now bound and ready for use with the transmitter.
- Select the desired model type (Fixed-Wing/Glider/Helicopter) and channels (6-10) on the transmitter as per your model's requirements.
Video 1: Demonstrates the binding process for the Flysky FS-i6X RC Transmitter with the FS-iA6B Receiver. This video shows how to connect the bind plug, power on the receiver and transmitter, and confirm successful binding.
3.2. Transmitter Overview
Familiarize yourself with the various components of the FS-i6X transmitter:
Figure 3: Labeled diagram of the FS-i6X transmitter, showing the antenna, handle, VRA/VRB, switches A/B/C/D, joysticks, fine-tuning rods, UP/DOWN buttons, Bind Key, OK/Cancel buttons, Power button, and LCD display.
4. Betjeningsvejledning
4.1. Grundlæggende kontrol
Use the joysticks to control your RC model. The left joystick typically controls throttle and rudder, while the right joystick controls aileron and elevator, depending on your chosen mode (Mode 1 or Mode 2).
4.2. Channel Expansion and Firmware
The FS-i6X supports firmware upgrades to expand the number of available channels. Refer to the official Flysky website for the latest firmware and instructions on how to perform updates.
4.3. Sensor Data and Telemetry
The system is capable of receiving data from various external sensors (e.g., temperature, altitude) and displaying it on the transmitter's LCD screen. This telemetry feature provides real-time information about your model.
Figure 4: The FS-iA6B receiver, illustrating its compact design and connection ports for servos and sensors. This image also highlights the dual-gain antenna for stable signal transmission.
5. Vedligeholdelse
- Rensning: Brug en blød, tør klud til at rengøre senderen og modtageren. Undgå at bruge opløsningsmidler eller slibende rengøringsmidler.
- Opbevaring: Store the transmitter and receiver in a cool, dry place away from direct sunlight and extreme temperatures. Remove batteries if storing for extended periods.
- Batteripleje: Ensure fresh batteries are used for optimal performance. Replace batteries when the low voltage alarmen udløses.
- Antenne inspektion: Regularly check the receiver antennas for any damage or kinks. Ensure they are positioned correctly for best signal reception.
6. Fejlfinding
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Senderen tænder ikke. | Lave eller døde batterier; forkert batteriindsætning. | Replace batteries with fresh AA batteries; ensure correct polarity. |
| Modtager er ikke bindende. | Incorrect binding procedure; bind plug not inserted correctly; transmitter too far from receiver. | Repeat binding steps carefully (refer to Section 3.1); ensure bind plug is fully inserted; keep transmitter and receiver close during binding. |
| Tab af kontrol under drift. | Out of range; interference; low transmitter/receiver battery voltage. | Operate within specified range; check for sources of interference; ensure batteries are fully charged. |
| Servos not responding. | Incorrect servo connection; faulty servo; receiver not powered. | Verify servo connections to the receiver; test with a different servo; ensure receiver has power. |
7. Specifikationer
7.1. FS-i6X Transmitter Specifications
- Produktmodel: FS-i6X
- Kanaler: 6-10 (standard 6)
- Modeller: Fixed wing / Glider / Helicopter / Boat
- Trådløs frekvens: 2.4 GHz
- Transmissionseffekt: < 20dBm
- Trådløs protokol: AFHDS 2A
- Rækkevidde: 500 ~ 1500m (in the air)
- Kanalopløsning: 4096
- Batteri: 1.5AA * 4
- Vise: STN transflective display, LCD 128x64 dot matrix
- Temperaturområde: -10°C ~ +60°C
- Fugtighedsområde: 20% - 95%
- Dimensioner: 174x89x190 mm
- Kropsvægt: 392 g
- Antenne type: Dobbelt antenne
- Lav voltage Alarm: < 4.2V
- Dataport: PS/2 (PPM)
- Opladningsport: Ingen
- Online opdatering: Ja
- Sprog: kinesisk og engelsk
- Certificering: CE certification, FCC ID: N4ZFLYSKYI6X
7.2. FS-iA6B Receiver Specifications
- Produktmodel: FS-iA6B
- PWM kanaler: 6
- Trådløs frekvens: 2.4 GHz
- Trådløs protokol: AFHDS 2A
- Rækkevidde: 500 ~ 1500m (in the air)
- Antenne type: Dual copper tube antenna (150mm * 2)
- Magt: 4.0-8.4V
- RSSI: Understøttet
- Dataport: PWM / PPM / I.bus / S.bus
- Temperaturområde: -10°C ~ +60°C
- Fugtighedsområde: 20% - 95%
- Online opdatering: Ja
- Dimensioner: 47 * 26.2 * 15 mm
- Vægt: 10 g
- Certificering: CE, RCM, FCC ID: N4ZFLYSKYIA10
Figure 5: Visual representation of the specifications for both the FS-i6X Transmitter and the FS-iA6B Receiver.
8. Garantioplysninger
GoolRC products typically come with a standard manufacturer's warranty. For specific details regarding the warranty period and coverage for your FS-i6X transmitter and FS-iA6B receiver, please refer to the warranty card included in your product packaging or visit the official GoolRC webwebsted. Gem din købsbevis til garantikrav.
9. Kundesupport
For technical assistance, troubleshooting, or any other inquiries, please contact GoolRC customer support. You can often find contact information on the product packaging, the official GoolRC webhjemmeside eller gennem din forhandler.
Visit the official GoolRC store for more products and information: GoolRC Store