1. Introduktion
This manual provides essential information for the safe and efficient operation of your EPEVER MPPT Tracer2210AN G3 Solar Charge Controller. The Tracer-AN G3 series represents a new generation of MPPT solar charge controllers designed to maximize photovoltaic power utilization and extend battery life. It features independent voltage control, allowing loads to be powered even without a connected battery. This controller offers broad compatibility with both lithium and lead-acid batteries (AGM, GEL, Flooded, User types).
Læs venligst denne manual grundigt inden installation og brug for at sikre korrekt funktionalitet og sikkerhed.
2. Sikkerhedsinstruktioner
- Sørg for, at al ledningsføring udføres af kvalificeret personale i overensstemmelse med lokale el-forskrifter.
- Frakobl altid solpanelet og batteriet, før du installerer eller justerer controlleren.
- Do not disassemble or attempt to repair the controller yourself. Contact authorized service personnel.
- Installer styreenheden i et godt ventileret område, væk fra brandfarlige materialer og direkte sollys.
- Ensure correct polarity for all connections (PV, battery, load) to prevent damage to the controller and other components.
- Use appropriate circuit breakers or fuses for PV, battery, and load circuits.
- Wear protective eyewear when working with batteries.
3. Produktet er slutview
3.1 Nøglefunktioner
- Advanced MPPT technology for maximum power point tracking efficiency.
- High tracking efficiency over 99.5% and conversion efficiency up to 98%.
- Supports 12V/24VDC system voltage auto-recognition.
- Compatible with lead-acid (AGM, GEL, Flooded, User) and lithium batteries.
- Independent voltage control for loads, enabling power supply without a connected battery.
- Low power consumption and silent operation.
- Comprehensive electronic protection functions.
- LCD display for system status and parameter settings.
3.2 Components and Interface
The EPEVER Tracer2210AN G3 controller features a clear interface for easy operation and monitoring.
Figure 1: EPEVER Tracer2210AN G3 Solar Charge Controller with labeled components.
| Ingen. | Komponent |
|---|---|
| 1 | SELECT-knap |
| 2 | RTS Interface (Remote Temperature Sensor) |
| 3 | PV terminaler |
| 4 | Batteriterminaler |
| 5 | Indlæs terminaler |
| 6 | RS485 Interface (non-isolated) |
| 7 | Mounting Hole (Φ 5mm) |
| 8 | ENTER -knap |
| 9 | LCD Display |
4. Opsætning og installation
4.1 Monteringssted
Vælg et monteringssted, der er:
- Well-ventilated to dissipate heat.
- Protected from direct sunlight, high temperatures, and moisture.
- Accessible for maintenance and wiring.
- Close to the battery, but in a separate, well-ventilated compartment if possible, to avoid battery gas corrosion.
4.2 Ledningsrækkefølge
Follow the wiring sequence carefully to prevent damage. Always connect the battery first, then the PV array, and finally the load.
- Tilslut batteriet: Connect the battery to the controller's battery terminals. Ensure correct polarity.
- Tilslut PV-panelet: Connect the solar panels to the controller's PV terminals. Ensure correct polarity.
- Tilslut belastningen: Tilslut DC-belastningen til regulatorens belastningsterminaler. Sørg for korrekt polaritet.
Figur 2: Eksample connection sequence for the solar charge controller.
Figure 3: Detailed step-by-step connection guide.
4.3 Batteritypekonfiguration
The controller supports various battery types. For optimal charging and discharge protection, select the correct battery type in the controller settings.
Figure 4: Supported battery types including Lead-Acid (Gel, AGM, Flooded, User) and Lithium (LiFePO4, Li(NiCoMn)O2).
- Bly-syre batterier: AGM, GEL, Flooded, and User-defined types are supported.
- Lithium-batterier: Supported. For detailed configuration of lithium battery parameters, optional EPEVER accessories such as a WiFi/Bluetooth adapter or a USB-RS485 cable are required.
5. Betjeningsvejledning
5.1 LCD-skærm
The integrated LCD displays real-time system information, including battery voltage, PV voltage, charging current, and load status. Use the SELECT and ENTER buttons to navigate through the display menus.
5.2 Knapfunktioner
- SELECT -knap: Used to switch between different display screens or menu options.
- ENTER knap: Used to confirm a selection or enter a menu for parameter modification.
5.3 Parameterindstillinger
Basic parameters can be viewed and adjusted directly via the LCD and buttons. For advanced settings, such as precise battery parameters or load control, external communication accessories are recommended.
Figure 5: The charge current is adjustable via a mobile application, with a minimum setting of 1A.
Optional accessories for advanced monitoring and configuration:
Figure 6: Accessory connection options (accessories not included).
6. Vedligeholdelse
Regelmæssig vedligeholdelse sikrer din solcelleladeregulators levetid og optimale ydeevne.
- Tjek forbindelser: Kontrollér regelmæssigt alle ledningsforbindelser for tæthed og korrosion. Spænd eventuelle løse forbindelser.
- Rengør controlleren: Hold controlleren ren og fri for støv og snavs. Brug en tør klud til rengøring. Brug ikke væsker.
- Undersøg for skader: Kontroller for eventuelle fysiske skader på casing, wires, or terminals.
- Ventilation: Sørg for, at ventilationsåbningerne ikke er blokerede, så varmen kan afledes korrekt.
- Batteriets sundhed: Overvåg batteri voltage and health. Ensure batteries are properly ventilated.
7. Fejlfinding
Hvis du støder på problemer med din controller, kan du se følgende almindelige problemer og løsninger:
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Intet display/Ingen strøm | Batteri ikke tilsluttet eller omvendt polaritet; Batterivolumentage for lavt. | Kontroller batteriforbindelser og polaritet. Sørg for batterivolumen.tage is above minimum operating voltage. |
| Ingen opladning | PV array not connected or reverse polarity; PV voltage too low; PV array shaded. | Check PV connections and polarity. Ensure PV voltage is within operating range. Clear any shading. |
| Indlæsningen virker ikke | Load not connected or reverse polarity; Load overcurrent/short circuit; Battery voltage for lavt. | Check load connections and polarity. Reduce load or check for short circuits. Charge battery. |
| Controller overophedning | Dårlig ventilation; For høj omgivelsestemperatur; Overbelastning. | Ensure adequate ventilation. Relocate controller if ambient temperature is too high. Reduce load. |
If the problem persists after attempting these solutions, please contact EPEVER customer support or your local dealer.
8. Specifikationer
8.1 Tekniske data
| Parameter | Værdi |
|---|---|
| Nominelt System Voltage | 12/24 VDC Auto |
| Nominel ladestrøm | 20A |
| Nominel afgangsstrøm | 20A |
| Rated Charge Power (12V/24V) | 260W/12V; 520W/24V |
| Maks. PV Open Circuit Voltage | 100V |
| Driftstemperatur | –25°C ~ +45°C |
| Beskyttelsesgrad | IP30 |
| Dimensioner (L x B x H) | 220 x 154 x 52mm (8.66 x 6.06 x 2.05 inches) |
| Vægt | 0.94 kg (2.07 lbs) |
| Display Type | LCD |
| Materiale | Plast |
8.2 Beskyttelsesfunktioner
- PV omvendt polaritetsbeskyttelse
- PV Overcurrent and Short Circuit Protection
- Indgang Overvoltage og Undervoltage Beskyttelse
- Batteribeskyttelse mod omvendt polaritet
- Beskyttelse mod overopladning og overafladning af batteriet
- Load Short Circuit and Overload Protection
- Controller Overheating Protection
- Battery Side Overcurrent Protection
9. Garanti og support
9.1 Garantioplysninger
The EPEVER MPPT Tracer2210AN G3 Solar Charge Controller comes with a 2 års producentgarantiDenne garanti dækker materiale- og fabrikationsfejl ved normal brug og service. Gem venligst din købsbevis i tilfælde af garantikrav.
9.2 Certificeringer
This product is certified with CE, FCC, IEC, ETL, and RoHS standards, ensuring compliance with international safety and environmental regulations.
9.3 Kundesupport
For technical assistance, warranty service, or any questions regarding your EPEVER product, please contact your authorized dealer or visit the official EPEVER webwebsted for supportressourcer.