Gebildet AC 110V 22mm LED Pilot Signal Light Instruction Manual

Indledning

Thank you for choosing the Gebildet AC 110V 22mm LED Pilot Signal Lights. These indicators are designed for clear visual signaling in various electrical equipment, machinery, and control panels. This manual provides essential information for safe installation, operation, and maintenance of your LED signal lights.

Image: A collection of Gebildet 22mm LED pilot signal lights, showcasing the available colors: red, green, blue, white, and yellow.

Produkt overview

Nøglefunktioner

• Voltage: 110V AC
• Strøm: 20mA
• Monteringshuls diameter: 22 mm
• LED farver: Red, Yellow, Blue, Green (available in various packs)
• Lysstyrke: ≥ 100cd/㎡
• Mekanisk levetid: ≥ 1,000,000 cyklusser
• Elektrisk levetid: ≥ 500,000 cyklusser
• Driftstemperatur: -25 ℃ til +55 ℃
• Stød- og vibrationsbestandig
• Materiale: Holdbar plastik
• Beskyttelsesklasse: IP65

Pakkens indhold

• 12 x LED Indicator Lights (typically 3 each of Red, Yellow, Blue, Green)
• Mounting Nuts and Washers (pre-assembled or included for installation)

Opsætning og installation

Sikkerhedsforanstaltninger

• Ensure power is disconnected from the circuit before attempting any installation.
• Installationen skal udføres af kvalificeret personale for at forhindre elektriske farer.
• Bekræft den korrekte voltage (110V AC) before connecting the indicator lights.

Monteringsvejledning

1. Drill a 22mm diameter hole in the desired panel location. The panel thickness should be between 1mm and 4mm.
2. Insert the LED indicator light into the drilled hole from the front of the panel.
3. From the rear of the panel, secure the indicator by tightening the provided mounting nut and washer.

Ledningsinstruktioner

Connect the two screw terminals located on the back of the indicator to your 110V AC power source. For AC indicators, polarity is generally not critical, but ensure all connections are secure and properly insulated to prevent short circuits.

Billede: Demonteret view of the LED indicator light, showing the main body, lens, mounting nut, washer, and screw terminals for electrical connection.

Betjeningsvejledning

Grundlæggende betjening

Once the LED indicator light is correctly installed and wired, it will illuminate when power is supplied to its terminals. The light serves as a clear visual signal for the operational status of the connected circuit or equipment.

Billede: Eksample application of Gebildet LED pilot lights on a control panel, illustrating their use for various status indications such as 'STOP', 'START-UP', 'FUNCTION', and 'SUSPEND'.

Opretholdelse

Rensning

To maintain optimal visibility, wipe the indicator lens with a soft, dry cloth. Avoid using abrasive cleaners, harsh chemicals, or solvents, as these can damage the plastic material.

Inspektion

Periodically inspect the wiring connections to ensure they remain tight and show no signs of wear or corrosion. Also, check that the mounting nut is securely fastened.

Beskyttende film

The indicator lens may come with a thin protective film. For the clearest display, gently peel this film off before initial use.

Image: Close-up of an LED indicator light, demonstrating the removal of the protective film from the lens for improved visibility and clarity.

Fejlfinding

Light Does Not Illuminate

• Tjek strømforsyningen: Ensure that 110V AC power is correctly supplied to the indicator terminals. Use a multimeter to verify voltage om nødvendigt.
• Tjek ledninger: Verify that all connections are secure and correctly wired according to the installation instructions.
• Undersøg for skader: Visually inspect the indicator for any visible damage to the housing or terminals.

Dæmpet eller flimrende lys

• Voltage Udsving: Ensure a stable 110V AC power source. Unstable voltage can cause inconsistent illumination.
• Løs forbindelse: Re-check all wiring connections to ensure they are tight and making good contact.

Billede: Intern view of an LED indicator light, pointing out the voltage stabilizing chip responsible for consistent brightness and extended operational life.

Tekniske specifikationer

Image: Dimensional diagram of the LED indicator light, detailing its physical measurements and key electrical specifications.

Garanti og support

Gebildet products are manufactured to high-quality standards. For any questions, technical assistance, or support regarding your LED Pilot Signal Lights, please contact your retailer or the manufacturer directly. Please retain your proof of purchase for warranty claims.