1. Introduktion
Thank you for choosing the Emtek 2105 Solid Brass Privacy Pocket Door Mortise Lock. This manual provides essential information for the proper installation, operation, and maintenance of your new lock. Please read these instructions carefully before beginning installation and retain them for future reference.
Figure 1: Emtek 2105 Solid Brass Privacy Pocket Door Mortise Lock in Satin Nickel finish.
2. Sikkerhedsoplysninger
- Always wear appropriate safety gear, such as safety glasses, during installation.
- Ensure the door thickness is 1-3/4 inches. This lock is designed specifically for this thickness.
- Use only the tools recommended in the installation section.
- Hold små dele væk fra børn.
- Hvis du er usikker på nogen del af installationsprocessen, skal du kontakte en kvalificeret fagmand.
3. Pakkens indhold
Kontroller, at alle komponenter er til stede, før installationen påbegyndes:
- Indstikslås
- Trim Plates (2)
- Slagplade
- Monteringsskruer
- Privacy Pin/Turn Mechanism (integrated or separate, depending on design)
- Emergency Release Tool (if applicable)
4. Installationsvejledning
This section outlines the general steps for installing your Emtek 2105 pocket door mortise lock. Specific door preparation may vary. Refer to the technical drawing for precise measurements.
4.1 Nødvendigt værktøj
- Bore
- Træ Mejsel
- Skruetrækker (Phillips hoved)
- Målebånd
- Blyant
4.2 Dørforberedelse
- Ensure your pocket door is 1-3/4 inches thick.
- Mark the desired height for the lock on the door edge.
- Using the technical drawing as a guide, mark the mortise pocket dimensions on the door edge and face.
- Carefully chisel out the mortise pocket to the required depth and dimensions for the lock body.
- Drill holes for the trim plate screws and the privacy mechanism spindle (if separate).
4.3 Installation af lås
- Insert the mortise lock body into the prepared pocket on the door edge. Ensure it fits snugly.
- Secure the mortise lock body to the door edge using the provided mounting screws.
- Attach the trim plates to both sides of the door, aligning them with the lock body and securing them with screws.
- Test the privacy mechanism to ensure smooth operation.
4.4 Montering af slutblege
- With the door closed, mark the position of the lock's bolt on the door frame.
- Chisel out a recess for the strike plate on the door frame, ensuring the bolt can fully engage.
- Secure the strike plate to the door frame with the provided screws.
- Test the lock by closing the door and engaging the privacy function to ensure proper alignment and secure locking.
Figure 2: Technical drawing showing dimensions of the Emtek 2105 Mortise Lock body, faceplate, and trim plate. Key dimensions include mortise body height 6.25", width 3.48", faceplate height 8", width 0.85", and trim plate height 7.50", width 2.50".
5. Betjeningsvejledning
The Emtek 2105 is a privacy mortise lock designed for pocket doors, offering privacy without requiring a key for daily use.
5.1 Låsning af døren
- From the inside of the room, locate the privacy turn or push-button mechanism on the trim plate.
- Rotate the turn or push the button to engage the lock bolt, securing the door.
5.2 Oplåsning af døren
- From the inside, rotate the privacy turn or push the button again to retract the lock bolt.
- From the outside, in case of emergency or accidental lockout, locate the emergency release hole on the trim plate. Insert a small, pointed object (e.g., a paperclip or the provided emergency release tool) into the hole and push or turn to disengage the lock.
6. Vedligeholdelse
Proper care will ensure the longevity and smooth operation of your Emtek mortise lock.
- Rensning: Rengør låsens yderflader med en blød, tør klud.amp klud. Undgå slibende rengøringsmidler, opløsningsmidler eller barske kemikalier, da disse kan beskadige den satinerede nikkelbelægning.
- Smøring: Periodically, apply a small amount of silicone-based lubricant to the moving parts of the mortise mechanism (e.g., bolt, latch) to ensure smooth operation. Do not use oil-based lubricants, as they can attract dust and grime.
- Inspektion: Regularly check all screws for tightness and ensure the lock operates freely without binding.
7. Fejlfinding
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Lock bolt does not engage fully. | Misalignment with strike plate; debris in mortise pocket; worn mechanism. | Check strike plate alignment and adjust if necessary. Clean mortise pocket. Lubricate mechanism. If issue persists, contact support. |
| Door is difficult to lock or unlock. | Lack of lubrication; binding components; door swelling. | Apply silicone lubricant to moving parts. Check for any obstructions. Ensure door operates smoothly within its track. |
| Trim plates are loose. | Monteringsskruerne er løse. | Spænd alle monteringsskruer. Spænd ikke for hårdt. |
8. Specifikationer
- Model: Emtek 2105
- Type: Privacy Pocket Door Indstikslås
- Materiale: Solid Brass (Metal)
- Slutte: Satin nikkel
- Dørtykkelse: 1-3/4 tommer (44.45 mm)
- Mortise Body Dimensions: Approximately 6.25" (H) x 3.48" (W) x 0.85" (D) (Refer to Figure 2 for detailed dimensions)
- Trim Plate Dimensions: Approximately 7.50" (H) x 2.50" (W)
- Vægt: Cirka 1.36 kg
- Inkluderede komponenter: Mortise Lock Body, Trim Plates, Strike Plate, Mounting Screws
9. Garantioplysninger
Emtek products are manufactured to high standards and are backed by a limited warranty. For specific warranty terms and conditions, please refer to the official Emtek webwebstedet eller kontakt kundesupport. Gem din købsbevis til garantikrav.
10. Kundesupport
If you have any questions, require assistance with installation, or need to report a problem, please contact Emtek customer support:
- Webwebsted: Visit the official Emtek webwebsted for ofte stillede spørgsmål og supportressourcer.
- Kontakte: Refer to the Emtek website for current contact information (phone, email).
Når du kontakter support, bedes du have dit produktmodelnummer (2105) og købsoplysninger klar.