TC Electronic JUNE-60 CHORUS Pedal Instruction Manual

1. Introduktion

The TC Electronic JUNE-60 CHORUS pedal is an authentic recreation of the legendary synthesizer chorus from the 1980s. This pedal features a simple 2-button interface for intuitive modulation tone and utilizes all-analog BBD (Bucket Brigade Delay) circuitry to deliver its classic sound. Designed for guitarists seeking vintage chorus effects, the JUNE-60 CHORUS also includes True Bypass for ultimate signal integrity.

TC Electronic JUNE-60 CHORUS Pedal, top-down view

Figur 1.1: Top-down view of the TC Electronic JUNE-60 CHORUS Pedal, showcasing its two yellow buttons and True Bypass footswitch.

2. Vigtige sikkerhedsinstruktioner

Læs disse instruktioner grundigt, inden du bruger apparatet.
Gem disse instruktioner til fremtidig reference.
Heed all warnings on the product and in the instructions.
Brug ikke dette apparat i nærheden af vand eller fugt.
Rengør kun med en tør klud.
Bloker ikke ventilationsåbninger. Installer i overensstemmelse med producentens anvisninger.
Må ikke installeres i nærheden af varmekilder såsom radiatorer, varmeapparater, komfurer eller andre apparater (inklusive ampløftere), der producerer varme.
Brug kun tilbehør/tilbehør specificeret af producenten.
Overlad al service til kvalificeret servicepersonale. Service er påkrævet, når apparatet er blevet beskadiget på nogen måde, såsom strømforsyningsledning eller stik er beskadiget, væske er blevet spildt, eller genstande er faldet ind i apparatet, apparatet har været udsat for regn eller fugt, ikke fungerer normalt , eller er blevet droppet.

3. Opsætning

3.1 Strømtilslutning

The JUNE-60 CHORUS pedal can be powered by a 9V battery or an external 9V DC power supply (not included). Ensure the power supply provides at least 100 mA. Connect the power supply to the 9V DC input jack on the rear of the pedal.

Batteristrøm: To install a 9V battery, open the battery compartment on the bottom of the pedal. Connect the battery to the clip and place it inside the compartment.
Ekstern strøm: Use a regulated 9V DC power supply with a center-negative plug, providing a minimum of 100 mA.

TC Electronic JUNE-60 CHORUS Pedal rear panel with input, output, and power jacks

Figure 3.1: Rear panel of the JUNE-60 CHORUS Pedal, showing the INPUT (MONO), 9V DC power input (100 mA), and OUTPUT (MONO/STEREO) jacks.

3.2 Lydforbindelser

Tilslut dit instrument (f.eks. guitar) til INPUT (MONO) stik ved hjælp af et standard 6,3 mm instrumentkabel. Tilslut OUTPUT (MONO/STEREO) stik til din amplifier or the next pedal in your signal chain. For stereo operation, use a Y-cable or two separate cables from the output to two amphøjttalere eller en stereoindgangsenhed.

Mono-opsætning: Connect a single 1/4-inch cable from the OUTPUT jack to your amplivligere.
Stereo opsætning: The JUNE-60 CHORUS supports stereo output. Consult your amplifier or audio interface manual for proper stereo input connections.

4. Betjening

The JUNE-60 CHORUS pedal features a straightforward 2-button interface, replicating the classic chorus modes of its inspiration. The pedal is activated by the True Bypass footswitch.

4.1 Aktivering af effekten

Tryk på ÆGTE OMGANG footswitch to toggle the effect on or off. When the effect is active, the LED indicator will illuminate.

4.2 Chorus Modes (Buttons I & II)

The two yellow buttons, labeled I og II, select different chorus modes. These buttons can be used individually or simultaneously to achieve distinct modulation characteristics.

Knap I: Engages Chorus Mode I, offering a specific modulation rate and depth.
Knap II: Engages Chorus Mode II, offering an alternative modulation rate and depth.
Buttons I & II (Simultaneously): Pressing both buttons together activates a combined chorus mode, often resulting in a richer, more complex modulation. Experiment with these combinations to find your desired sound.

TC Electronic JUNE-60 CHORUS Pedal top view showing buttons I and II

Figur 4.1: Øverst view of the JUNE-60 CHORUS Pedal, highlighting the two yellow buttons (I and II) for chorus mode selection.

4.3 Mono/Stereo Switch

A small switch labeled MONO / STEREO is located near the chorus mode buttons. This switch determines the output configuration of the pedal.

MONO: For single ampopsætning af lifner.
STEREOANLÆG: For dual amplifier or stereo input setups, providing a wider, more immersive chorus effect.

5. Vedligeholdelse

5.1 Rengøring

Clean the pedal's exterior with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these may damage the finish or internal components.

5.2 Udskiftning af batteri

If using battery power, replace the 9V battery when the effect LED dims or the pedal's performance degrades. To replace, open the battery compartment on the bottom of the unit, disconnect the old battery, and connect a new one, ensuring correct polarity.

5.3 Opbevaring

When not in use for extended periods, disconnect the power supply and remove the battery to prevent leakage. Store the pedal in a cool, dry place away from direct sunlight and extreme temperatures.

6. Fejlfinding

Problem	Mulig årsag	Løsning
Ingen lyd når pedalen er trådt i.	No power, incorrect cable connection, faulty cable.	Check power supply connection and ensure it meets 9V DC, 100mA specifications. Replace battery if using battery power. Kontroller, at alle lydkabler er korrekt tilsluttet. Test cables with another device to ensure they are not faulty.
Svag eller forvrænget lyd.	Low battery, incorrect input level from instrument.	Replace battery or use external power supply. Ensure instrument output level is appropriate for pedal input.
Chorus effect is not noticeable.	Incorrect chorus mode selected, subtle setting.	Experiment with pressing Button I, Button II, or both simultaneously. Ensure the MONO/STEREO switch is set correctly for your setup.
Pedal does not power on with adapter.	Insufficient current from power adapter.	Verify your power adapter provides at least 100 mA at 9V DC. Some adapters may provide 9V but insufficient current.

7. Specifikationer

Feature	Detalje
Model	JUNE-60 CHORUS
Effekt Type	Kor
Kredsløb	All-analog BBD (Bucket Brigade Delay)
Bypass	Ægte bypass
Kontrolelementer	2 x Chorus Mode Buttons (I, II), MONO/STEREO Switch, True Bypass Footswitch
Indgang tilslutning	1 x 1/4" TS, unbalanced (Mono)
Udgangsstik	1 x 1/4" TS, unbalanced (Mono/Stereo)
Strømindgang	Standard 9V DC, center-negative, >100 mA (Power supply not included)
Batteriindstilling	9V batteri (medfølger ikke)
Dimensioner (H x B x D)	Cirka 13.7 x 8.6 x 5.6 tommer
Vægt	8 ounces (0.5 lbs)
Kropsmateriale	Plast, Metal

TC Electronic JUNE-60 CHORUS Pedal bottom label with regulatory information

Figure 7.1: Bottom label of the JUNE-60 CHORUS Pedal, displaying model and regulatory compliance information.

8. Garanti og support

8.1 Garantioplysninger

TC Electronic products are designed and manufactured to the highest standards. For detailed warranty terms and conditions, please refer to the official TC Electronic webwebstedet eller garantikortet, der fulgte med dit produkt. Gem din købsbevis til eventuelle garantikrav.

8.2 Kundesupport

Should you encounter any issues or have questions regarding your JUNE-60 CHORUS pedal, please visit the official TC Electronic support page for FAQs, troubleshooting guides, and contact information. You can find support resources at the TC Elektronisk Support Webwebsted.