1. Introduktion
This manual provides detailed instructions for the installation, operation, and maintenance of the MEAN WELL RS-150-15 Single Output Switching Power Supply. This high-efficiency power supply delivers a stable 15V DC output with a rated current of 10A, providing 150W of power. It is designed for various industrial and scientific applications, featuring robust protection mechanisms and a compact design.
2. Sikkerhedsoplysninger og vigtige bemærkninger
Please read all safety instructions carefully before installation and operation to prevent injury or damage to the unit. Keep this manual for future reference.
- Generel sikkerhed: This power supply is considered a component and must be installed into a final equipment. The final equipment must be re-confirmed to meet all relevant EMC directives.
- Input bindtage Valg: The unit supports both 88-132VAC and 176-264VAC input ranges, selectable via a switch. Ensure the correct voltage is selected before connecting to the AC mains.
- Miljøforhold: Operate the power supply within the specified working temperature (-25°C to +70°C) and humidity (20% to 95% RH non-condensing) ranges. Avoid exposure to excessive moisture or extreme temperatures.
- Køling: The unit is cooled by free air convection. Ensure adequate airflow around the power supply to prevent overheating.
- Beskyttelsesfunktioner: The power supply includes built-in protections against short circuit, overload, and over voltage. In case of a fault, the unit will enter hiccup mode and automatically recover once the fault condition is removed.
- Ledningsføring: All parameters are measured at 230VAC input, rated load, and 25°C ambient temperature unless otherwise specified. Ripple and noise are measured with a 12" twisted pair-wire terminated with 0.1uF & 47uF parallel capacitors.
- Installation: Ensure proper grounding (FG) connection for safety.
- Tænd sekvens: Turning the power supply ON/OFF very quickly may increase the setup time.
3. Funktioner
- Universal AC input / Full range (selectable by switch)
- Protections: Short circuit, overload, over voltage
- Køling ved fri luftkonvektion
- LED-indikator for tænding
- 100 % fuld belastning indbrændingstest
- Utilizes 105°C long life electrolytic capacitors
- Withstands 300VAC surge input for 5 seconds
- Høj driftstemperatur op til 70°C
- Withstands 5G vibration test
- Høj effektivitet, lang levetid og høj pålidelighed
4. Opsætning og installation
Proper installation is crucial for the safe and reliable operation of the power supply. Refer to the mechanical specifications and terminal assignments for correct wiring.
4.1 Mechanical Dimensions and Mounting
The power supply features a compact design for easy integration. Ensure sufficient space for air circulation around the unit for optimal cooling.
Figur 1: Mechanical dimensions and mounting points of the RS-150-15 power supply. Dimensions are in millimeters. The unit measures 197mm (L) x 98mm (W) x 38mm (H).
Mount the power supply securely using the designated mounting holes as shown in Figure 1. Ensure the mounting surface is stable and can support the weight of the unit (approximately 0.7 kg).
4.2 Terminal Assignment
Connect the input and output wires according to the terminal assignments below. Use appropriate wire gauges for the current ratings to prevent overheating.
| Pin nr. | Opgave | Pin nr. | Opgave |
|---|---|---|---|
| 1 | AC/N | 4, 5 | DC OUTPUT -V |
| 2 | AC/L | 6, 7 | DC OUTPUT +V |
| 3 | FG (Frame Ground) |
Vigtig: Ensure the Frame Ground (FG) terminal is properly connected to earth ground for safety.
4.3 Indgang Voltage Valg
The RS-150-15 has a switch to select between 88-132VAC and 176-264VAC input voltage rækker. Before connecting the power supply to the AC mains, verify that the switch is set to match your local AC supply voltage. Forkert voltagDette valg kan beskadige enheden.
5. Betjeningsvejledning
Once properly installed and wired, the power supply is ready for operation.
- Tænd: Connect the AC input to the power supply. The LED indicator on the unit will illuminate, indicating that the power supply is active.
- Udgang Voltage Justering: Output voltage can be adjusted within the range of 13.5V to 16.5V using the internal potentiometer. Use a voltmeter to accurately set the desired output voltage.
- Belastningsforbindelse: Connect your DC load to the +V and -V output terminals. Ensure the load does not exceed the rated current of 10A or the rated power of 150W.
- Reduktionskurve: For operation at higher ambient temperatures or lower input voltages, refer to the derating curves in the specifications section to ensure the power supply operates within its safe limits.
Figur 2: Specification sheet for the RS-150-15, including derating curves and static characteristics. The derating curve illustrates the maximum permissible load at various ambient temperatures, while static characteristics show performance across input voltage rækker.
6. Vedligeholdelse
The MEAN WELL RS-150-15 power supply is designed for long-term, reliable operation with minimal maintenance. However, adhering to the following guidelines will help ensure its longevity:
- Hold rent: Periodically inspect the unit for dust accumulation, especially around ventilation openings. Clean with a soft, dry cloth or compressed air. Do not use liquid cleaners.
- Sørg for luftgennemstrømning: Verify that the free air convection cooling is not obstructed. Maintain adequate clearance around the power supply.
- Miljøkontrol: Operate the unit within the specified temperature and humidity ranges. Avoid environments with high levels of corrosive gases or excessive vibration.
- Forbindelsesintegritet: Kontrollér regelmæssigt alle indgangs- og udgangsforbindelser for at sikre, at de er fastgjorte og fri for korrosion.
7. Fejlfinding
If the power supply is not functioning as expected, consider the following common issues and their solutions:
- No Output / LED Off:
- Check the AC input connection and ensure power is supplied to the unit.
- Bekræft input voltage selection switch is set correctly for your AC mains.
- Inspect the input fuse (if accessible and replaceable) for continuity.
- Intermittent Output / Hiccup Mode:
- This indicates that one of the protection features (short circuit, overload, or over voltage) has been activated.
- Disconnect the load and check for short circuits in your external circuit.
- Ensure the load current does not exceed 10A and the power does not exceed 150W.
- Kontroller, om udgangsvolumentage is set too high (above 16.5V).
- Allow the unit to cool down if it has been operating in a high-temperature environment, as over-temperature protection may be active.
- Udgang Voltage Forkert:
- Use a voltmeter to measure the output voltage.
- Adjust the internal potentiometer to set the desired output voltage inden for området 13.5V til 16.5V.
- Ensure the load is not drawing excessive current, which could cause voltage drop.
Hvis problemet fortsætter efter at have udført disse kontroller, skal du kontakte kvalificeret servicepersonale.
8. Specifications (Model: RS-150-15)
The following table details the technical specifications for the MEAN WELL RS-150-15 power supply.
| Karakteristisk | Værdi |
|---|---|
| PRODUKTION | |
| DC bindtage | 15V |
| Nominel strøm | 10A |
| Nominel effekt | 150W |
| Ripple & Noise (maks.) | 120mVp-p |
| Voltage ADJ. Range | 13.5 ~ 16.5V |
| Voltage Tolerance | ±1.0 % |
| Linjeregulering | ±0.5 % |
| Belastningsregulering | ±0.5 % |
| Setup, Rise, Hold Time | 800ms, 30ms, 10ms (at 230VAC full load) |
| INPUT | |
| VoltagRækkevidde | 88 ~ 132VAC / 176 ~ 264VAC (selected by switch) |
| Frekvensområde | 47 ~ 63Hz |
| Effektivitet (Typ.) | 84 % |
| AC-strøm (Typ.) | 2.5A/230VAC |
| Startstrøm (Typ.) | KALT START 40A / 230VAC |
| Lækstrøm | <2mA/240VAC |
| BESKYTTELSE | |
| Overbelaste | 110 ~ 150% rated output power. Protection type: Hiccup mode, recovers automatically after fault condition is removed. |
| Over Voltage | 17.25 ~ 20.25V. Protection type: Hiccup mode, recovers automatically after fault condition is removed. |
| Over temperatur | Ja |
| MILJØ | |
| Arbejdstemperatur | -25 ~ +70°C (Se Derating Curve) |
| Arbejdsfugtighed | 20 ~ 95% RH ikke-kondenserende |
| Opbevaringstemperatur | -40 ~ +85°C, 10 ~ 95% RH |
| Temperaturkoefficient | ±0.03%/°C (0~50°C) |
| Vibration | 10 ~ 500 Hz, 5G 10 min./1 cyklus, periode i 60 min. hver langs X-, Y-, Z-akser |
| SIKKERHED & EMC | |
| Sikkerhedsstandarder | UL60950-1, TUV EN60950-1 approved |
| Modstå Voltage | I/P-O/P:3KVAC, I/P-FG:1.5KVAC, O/P-FG:0.5KVAC |
| Isolationsmodstand | I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25°C/70% RH |
| EMC-emission | Compliance to EN55022 (CISPR22) class B, EN61000-3-2,-3 |
| EMC-immunitet | Compliance to EN61000-4-2,3,4,5,6,8,11, EN61000-6-2 (EN50082-2), heavy industry level, criteria A |
| ANDRE | |
| MTBF | 244Khrs min. MIL-HDBK-217F (25°C) |
| Dimension (L x B x H) | 197 x 98 x 38 mm |
| Vægt | 0.7 kg |
9. Garanti og support
The MEAN WELL RS-150-15 Switching Power Supply comes with a 3 års garanti from the date of purchase, covering defects in materials and workmanship under normal use. For warranty claims or technical support, please contact your authorized MEAN WELL distributor or reseller.
For additional information or specific technical inquiries, please refer to the official MEAN WELL webwebsted eller kontakt deres kundeserviceafdeling.