MICHELIN 12294A

Michelin 12294A Digital Programmable Tire Pressure Gauge

Brugermanual

Indledning

Thank you for choosing the Michelin 12294A Digital Programmable Tire Pressure Gauge. This device is designed for accurate and convenient measurement of tire pressure, ensuring optimal vehicle performance and safety. Please read this manual thoroughly before use.

Pakkens indhold

  • 1 x Michelin 12294A Digital Programmable Tire Pressure Gauge
  • 2 x Lithium-metal batteries (pre-installed or included)
Michelin 12294A Digital Programmable Tire Pressure Gauge

Image: The Michelin 12294A Digital Programmable Tire Pressure Gauge, showing its digital display and control buttons.

Opsætning

Installation af batteri

The device requires 2 Lithium-metal batteries. These are typically included or pre-installed. If replacement is needed:

  1. Locate the battery compartment cover, usually on the back or side of the unit.
  2. Åbn låget.
  3. Indsæt batterierne, og sørg for korrekt polaritet (+/-).
  4. Luk batterirummets dæksel forsvarligt.

Tænd/sluk

  • For at tænde skal du trykke på Power-knap (often marked with a circle and vertical line symbol).
  • The backlit LCD display will illuminate.
  • Enheden slukker automatisk efter en periode med inaktivitet for at spare på batteriet.

Betjeningsvejledning

Måling af dæktryk

  1. Ensure the tire is cold for the most accurate reading.
  2. Fjern ventilhætten fra dækket.
  3. Press the nozzle of the gauge firmly onto the tire valve stem. A good seal is crucial for an accurate reading.
  4. The digital display will show the tire pressure.
  5. Remove the gauge from the valve stem. The reading will hold on the display for a short period.
  6. Udskift ventilhætten.
Michelin 12294A Tire Pressure Gauge in use on a car tire

Image: The Michelin 12294A gauge being used to measure pressure on a car tire valve.

Ændring af måleenheder

The gauge supports measurements in PSI, KPA, BAR, and kg/cm². To cycle through units, press the Enhedsknap (often the same as the power button or a dedicated button). The current unit will be displayed on the screen.

Programming Tire Pressures

This gauge can be programmed with target front and rear tire pressures for up to two vehicles. Refer to your vehicle's owner's manual or the sticker on the driver's side door jamb for recommended tire pressures.

  1. With the gauge powered on, press and hold the Program knap (often an arrow button or a dedicated 'SET' button) until the programming mode is activated.
  2. Brug Op/Ned piletaster to adjust the target pressure for the front tires of Vehicle 1.
  3. Tryk på Program knap again to switch to the rear tires of Vehicle 1, then adjust.
  4. Repeat the process for Vehicle 2 if desired.
  5. The gauge will save the settings automatically after a few seconds of inactivity or by pressing the Program button to exit.
Close-up of Michelin 12294A display showing current and target PSI

Billede: Et nærbillede view of the gauge's digital display, showing current pressure and programmable target pressure settings.

Using the Integrated Flashlight

The gauge features an integrated flashlight to assist in locating the tire valve in low-light conditions. To activate the flashlight, press the Lommelygte knap (refer to device markings, often combined with another function or a dedicated button).

Using the Bleed Valve

If a tire is over-inflated, the built-in bleed valve allows for controlled release of air. While the gauge is attached to the valve stem and displaying pressure, gently press the Bleed Valve button (if present, often a small button near the nozzle) to release air until the desired pressure is reached.

Opretholdelse

  • Rensning: Tør måleren af ​​med en blød, tør klud. Brug ikke slibende rengøringsmidler, og nedsænk ikke apparatet i vand.
  • Opbevaring: Opbevar måleren et køligt, tørt sted, væk fra direkte sollys og ekstreme temperaturer.
  • Udskiftning af batteri: If the display becomes dim or the device does not power on, replace the batteries. Dispose of old batteries according to local regulations.

Fejlfinding

Problem Mulig årsag Løsning
No display/Device does not power on Døde eller forkert installerede batterier. Kontroller batteripolariteten, eller udskift batterierne.
Upræcis læsning Poor seal with valve stem; tire not cold; gauge malfunction. Ensure a firm, airtight seal. Measure when tires are cold. If issues persist, contact support.
Air leaks when measuring Gauge not properly seated on valve stem. Press the gauge firmly and squarely onto the valve stem.

Specifikationer

Mærke MICHELIN
Modelnummer 12294A
Modelnavn Trykmåler
Produktets vægt 100 g
Produktdimensioner 9.3 x 3.3 x 2 cm
Batterier 2 Lithium-metal (included)
Måleenheder PSI, kPA, BAR, kg/cm²
Nøjagtighed +/- 1 %
Materiale Metal core, ribbed plastic exterior
Trådtype Schrader

Garanti og support

This Michelin product is manufactured to high-quality standards. For warranty information or technical support, please refer to the documentation included with your purchase or visit the official Michelin automotive accessories webwebsted. Gem din købsbevis til garantikrav.

© 2023 Michelin. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.