Airam LED Cabinet Lamp 1.2W brugsanvisning

1. Introduktion

This manual provides essential instructions for the safe and efficient use of your Airam LED Cabinet Lamp 1.2W. This battery-operated lamp features a PIR motion sensor, automatically illuminating when motion is detected, making it ideal for cabinets, drawers, and other enclosed spaces. Please read this manual thoroughly before installation and operation.

2. Opsætning

2.1 Pakkens indhold

Før du fortsætter, skal du sørge for, at alle komponenter er til stede:

• Airam LED Cabinet Lamp 1.2W
• Mounting hardware (screws or adhesive strips, typically included in packaging)

Figure 1: Airam LED Cabinet Lamp in its retail packaging, showing the lamp and typical mounting accessories.

2.2 Batteriinstallation

The Airam LED Cabinet Lamp requires 4 x AA 1.5V batteries (not included).

1. Locate the battery compartment cover on the back or side of the lamp.
2. Skub eller afklips dækslet for at åbne rummet.
3. Insert 4 AA batteries, ensuring correct polarity (+ and - terminals match the markings inside the compartment).
4. Luk batterirummets dæksel forsvarligt.

2.3 Montering af Lamp

Lamp can be mounted using screws or adhesive strips, depending on the included hardware and your preference. Choose a location where the motion sensor has a clear line of sight to the area where movement is expected (e.g., inside a cabinet door, above a drawer).

Figur 2: Forside view of the Airam LED Cabinet Lamp, highlighting the central motion sensor.

Using Screws (if applicable):

1. Mark the desired mounting position.
2. Drill pilot holes if necessary, matching the lamp's mounting holes.
3. Fastgør lamp ved hjælp af de medfølgende skruer.

Using Adhesive Strips (if applicable):

1. Rengør monteringsfladen grundigt for at sikre, at den er tør og fri for støv eller fedt.
2. Fjern den beskyttende bagside fra de klæbende striber.
3. Firmly press the lamp onto the desired surface for at least 30 seconds.

3. Betjening

The Airam LED Cabinet Lamp is designed for automatic operation using its integrated PIR (Passive Infrared) motion sensor.

1. Once batteries are installed and the lamp is mounted, it will enter standby mode.
2. When the PIR motion sensor detects movement within its range (e.g., opening a cabinet door or drawer), the LED lights will automatically turn on.
3. Lamp will remain illuminated for approximately 25 seconds after motion is detected.
4. If no further motion is detected within this period, the lamp will automatically turn off to conserve battery power.
5. If continuous motion is detected, the lamp will remain on until motion ceases for 25 seconds.

Note: Ensure the motion sensor is not obstructed for optimal performance.

4. Vedligeholdelse

4.1 Udskiftning af batteri

Når lysudbyttet aftager, eller lamp stops functioning, it is time to replace the batteries. Refer to section 2.2 Batteriinstallation for detaljerede instruktioner.

• Always replace all 4 AA batteries at the same time.
• Bland ikke gamle og nye batterier eller forskellige typer batterier.
• Bortskaf brugte batterier ansvarligt i henhold til lokale regler.

4.2 Rengøring

Lamp is constructed from polycarbonate and ABS plastic. To clean the lamp:

• Tør overfladen af ​​med en blød, tør eller let fugtet kludamp klæde.
• Do not use abrasive cleaners, solvents, or harsh chemicals, as these can damage the plastic finish or the sensor.
• Ensure no liquid enters the battery compartment or sensor area.

5. Fejlfinding

6. Specifikationer

7. Garanti og support

Specifikke garantioplysninger kan variere afhængigt af region og forhandler. Se venligst din købsdokumentation eller kontakt din forhandler for detaljer vedrørende garantidækning.

For technical support or further assistance, please contact the manufacturer, Bot Lighting, or your retailer. Keep your purchase receipt as proof of purchase.