Legrand 1597TRW Tamper Resistant GFCI Wall Outlet User Manual

Indledning

This manual provides detailed instructions for the safe installation, operation, and maintenance of the Legrand 1597TRW Tamper Resistant GFCI Wall Outlet. This device is part of the radiant collection, designed to offer reliable electrical protection in residential and commercial environments. Please read these instructions thoroughly before beginning installation or use.

Sikkerhedsoplysninger

WARNING: Risk of electric shock. May cause serious injury or death. Turn off power at the circuit breaker or fuse box before installation.

Always disconnect power at the service panel before working with electrical wiring.
Installationen skal udføres af en kvalificeret elektriker eller i overensstemmelse med alle lokale og nationale el-forskrifter.
Må ikke installeres i våde omgivelser, medmindre den specifikt er beregnet til sådan brug.
Sørg for, at alle ledningsforbindelser er sikre og korrekt isolerede.
Test the GFCI outlet monthly to ensure proper operation.

Pakkens indhold

Kontroller, at alle komponenter er til stede, før installationen påbegyndes:

Legrand 1597TRW Tamper Resistant GFCI Wall Outlet (White)
Monteringsskruer
Instruktionsmanual (dette dokument)

Note: A screwless wall plate is not included and must be purchased separately.

Installation

Follow these steps for proper installation of your GFCI outlet:

Sluk for strømmen: Locate the circuit breaker or fuse that supplies power to the outlet box. Turn it off completely. Verify power is off using a voltage tester.
Fjern gammel stikkontakt: Carefully remove the existing wall plate and outlet from the electrical box. Disconnect the wires from the old outlet, noting which wires were connected to the "LINE" and "LOAD" terminals.
Identificér ledninger:
- LINE Wires: These wires bring power from the circuit breaker to the GFCI outlet.
- LOAD Wires: These wires carry power from the GFCI outlet to other downstream receptacles or devices that you want to protect. If there are no downstream receptacles, cap the LOAD wires individually.
- Jordledning: Typically bare copper or green insulated.
Connect Wires to GFCI:
- Tilslut LINE wires to the terminals marked "LINE" on the GFCI outlet.
- Tilslut LÆS wires to the terminals marked "LOAD" on the GFCI outlet.
- Tilslut jordledning to the green ground screw.
Vigtig: The Legrand 1597TRW features a feed-thru wiring configuration that allows the GFCI to protect downstream receptacles. It also prevents line-load reversal miswire, meaning there will be no power to the face or downstream receptacles if wired incorrectly. An auto-ground clip assures a positive ground to a metal box.
Monter stikkontakten: Carefully fold the wires into the electrical box and secure the GFCI outlet to the box using the provided mounting screws.
Installer vægplade: Attach the screwless wall plate (not included) over the GFCI outlet.
Gendan strøm: Tænd for strømmen igen ved afbryderen.

Billede: Forside view of the Legrand 1597TRW Tamper Resistant GFCI Wall Outlet. This image shows the two tamper-resistant receptacles, the TEST button (black), and the RESET button (red).

Operation

The GFCI outlet is designed to protect against electrical shock by quickly shutting off power if a ground fault is detected.

Genstarts knap: Efter installation eller strømafbrydelsetage, press the red RESET button to restore power to the outlet.
TEST knap: Press the black TEST button to simulate a ground fault. The GFCI should trip, and power to the outlet will be cut off. This confirms the GFCI is functioning correctly.

Månedlig test:

It is recommended to test your GFCI outlet monthly to ensure it is providing continuous protection. To test:

Stik alamp or other device into the GFCI outlet and turn it on.
Press the black TEST button. The lamp should turn off, and the red RESET button should pop out.
Press the red RESET button. The lamp should turn back on.
Hvis lamp does not turn off or on as described, the GFCI may be faulty and should be replaced.

Opretholdelse

The Legrand 1597TRW GFCI outlet requires minimal maintenance. Regular testing is the primary maintenance procedure.

Keep the outlet clean and free from dust and debris.
Do not paint over the GFCI outlet or its buttons, as this can impair operation.
If the GFCI trips frequently without an apparent cause, consult a qualified electrician to inspect your wiring.

Fejlfinding

Problem	Mulig årsag	Løsning
GFCI will not reset.	No power to the GFCI. Jordfejl opdaget. Line-load reversal miswire. Faulty GFCI.	Tjek afbryderen. Unplug all devices from the GFCI and downstream outlets. Try to reset. If it resets, plug devices back in one by one to identify the faulty device. Verify wiring connections (LINE to LINE, LOAD to LOAD). Replace the GFCI.
GFCI udløses ofte.	Faulty appliance/device. Moisture in the circuit. Beskadigede ledninger.	Identify and remove the faulty appliance. Ensure the environment is dry. Consult a qualified electrician to inspect wiring.
Ingen strøm til stikkontakten.	GFCI udløste. Effektafbryder udløst. Forkert ledningsføring.	Tryk på RESET-knappen. Kontroller og nulstil afbryderen. Kontroller ledningsforbindelserne.

Specifikationer

Model: 1597TRW
Mærke: Legrand
Farve: Hvid
Ampalder: 15 Amps
Voltage: 125 volt
Samlet strømudtag: 2
Connector Type: Nema 5-15
Materiale: Metal
Funktioner: Tamper Resistant, Auto-Ground Clip, Feed-Thru Wiring, Line-Load Reversal Miswire Prevention
UPC: 680147085438
ASIN: B079LTP7Y5

Garanti og support

Legrand products are designed and manufactured to the highest quality standards. For specific warranty information, please refer to the documentation included with your purchase or visit the official Legrand website. For technical support or further assistance, please contact Legrand customer service.

Contact information for Legrand can typically be found on their official webwebsted eller produktemballage.

Legrand 1597TRW