Mackie HM-800 8-Channel Headphone Amplivligere brugervejledning

1. Produktet er slutview

The Mackie HM-800 is a 19-inch rackmount 8-channel headphone amplifier designed for professional audio environments such as studios, houses of worship, and practice spaces. It provides extensive monitoring capabilities with up to 10 available mixes and a total of 16 headphone outputs. The unit features two discrete main stereo inputs with individual level control and stereo outputs, alongside auxiliary inputs for each channel.

Nøglefunktioner:

• 16 Total Headphone Outputs: Two outputs per channel for extensive monitoring.
• Dual Main Stereo Inputs: Two discrete main stereo inputs with separate level control and stereo outputs.
• Auxiliary Inputs Per Channel: Allows for individual mix customization for each of the 8 channels.
• 7-Segment LED Metering: Visual level indication for both main inputs and individual channels.
• Input Select and Stereo/Mono Switches: Per channel controls for flexible signal routing and monitoring modes.

2. Opsætningsvejledning

2.1 Udpakning og inspektion

Carefully unpack the HM-800 and inspect it for any signs of damage. Retain the packaging for future transport or storage.

2.2 Rackmontering

The HM-800 is designed for standard 19-inch rack mounting. Secure the unit using appropriate rack screws to ensure stability.

2.3 Strømtilslutning

Connect the supplied AC power cord to the HM-800's power inlet on the rear panel and then to a suitable AC power outlet. Ensure the voltage selector switch (if present) matches your local power supply before connecting.

Figure 1: Rear panel connections, including power input and fuse holder.

2.4 Lydindgangsforbindelser

• Main Inputs (IN 1, IN 2): Connect your primary stereo audio sources (e.g., mixer main outputs, audio interface outputs) to the MAIN IN 1 and MAIN IN 2 TRS inputs on the rear panel. These inputs are balanced/unbalanced.
• Auxiliary Inputs (AUX INPUTS 1-8): For individual channel mixes, connect auxiliary audio sources to the corresponding AUX INPUTS (1-8) on the rear panel. These inputs are typically used for 'more me' mixes or specific instrument feeds.

2.5 Main Output Connections

The HM-800 provides MAIN OUT 1 and MAIN OUT 2 TRS outputs on the rear panel. These can be used to pass the main input signals through to other equipment or to monitor the main mix on studio monitors.

2.6 Headphone Connections

Connect headphones to the PHONES outputs on the front panel. Each of the 8 channels has two headphone outputs, allowing for a total of 16 headphone connections.

Figure 2: Front panel controls and headphone outputs.

3. Betjeningsvejledning

3.1 Tænd/sluk

After all connections are made, press the POWER switch on the front panel to turn the unit on. The power LED will illuminate. Always power on the HM-800 after other audio equipment and power it off before other equipment to prevent pops or thumps.

3.2 Main Input Level Control

Adjust the MAIN IN 1 and MAIN IN 2 level controls on the front panel to set the overall input level for the main stereo signals. Monitor the 7-segment LED meters to ensure levels are optimal without clipping.

3.3 Channel Input Selection

Each of the 8 channels has an INPUT SELECT switch. This switch determines which main input (IN 1 or IN 2) feeds the channel. If an auxiliary input is connected to a channel, it will override the main input selection for that specific channel.

3.4 Stereo/Mono Monitoring

The STEREO/MONO switch on each channel allows you to monitor the selected input signal in either stereo or summed mono. Use mono for checking phase compatibility or when a mono source is preferred.

3.5 Channel Output Level Control

The OUTPUT knob for each channel controls the headphone volume for that specific channel's two headphone outputs. Adjust these individually for each listener.

3.6 LED-måling

The 7-segment LED meters provide visual feedback on the audio levels. Aim for levels that are consistently in the green or yellow range, avoiding sustained red indications which signify clipping and potential distortion.

4. Vedligeholdelse

4.1 Rengøring

Clean the exterior of the HM-800 with a soft, dry cloth. Avoid using abrasive cleaners or solvents that could damage the finish or internal components. Ensure the unit is powered off and unplugged before cleaning.

4.2 Ventilation

Ensure that the ventilation slots on the unit are not obstructed. Proper airflow is essential to prevent overheating and maintain optimal performance.

4.3 Udskiftning af sikringer

The HM-800 is equipped with a user-replaceable fuse located near the AC power inlet on the rear panel. If the unit fails to power on, check the fuse. Always replace it with a fuse of the exact same type and rating as specified on the unit (e.g., T1.6AL 250V for 100-120V operation, T0.5AL 250V for 220-240V operation).

5. Fejlfinding

5.1 Ingen strøm

• Verify the power cord is securely connected to both the HM-800 and a working AC outlet.
• Kontroller tænd/sluk-knappen på frontpanelet.
• Inspect the fuse on the rear panel and replace if blown (refer to Section 4.3).

5.2 No Sound from Headphones

• Ensure headphones are properly plugged into the PHONES outputs.
• Check the OUTPUT level knob for the specific channel; it may be turned down.
• Verify that the main input sources are sending audio and that their levels are adequate.
• Confirm the INPUT SELECT switch for the channel is set correctly (IN 1 or IN 2), or that the auxiliary input is properly connected and sending signal.
• Test med forskellige hovedtelefoner for at udelukke defekte hovedtelefoner.

5.3 Forvrænget lyd

• Reduce the input level from your source to the HM-800's main inputs.
• Lower the MAIN IN 1 or MAIN IN 2 level controls on the HM-800.
• Check the 7-segment LED meters for clipping (sustained red lights) and adjust levels accordingly.
• Sørg for, at alle kabler er i god stand og korrekt tilsluttet.

5.4 Sound Only from One Side of Headphones

• Verify that the audio source connected to the HM-800 is stereo and balanced, if applicable.
• Check the STEREO/MONO switch for the affected channel; ensure it is set to STEREO if stereo monitoring is desired.
• Test with different headphones to confirm the issue is not with the headphones themselves.
• Inspect the headphone cable for damage or improper connection.

6. Specifikationer

7. Garantioplysninger

The Mackie HM-800 comes with a 1-year all-inclusive, non-transferable warranty. Please retain your proof of purchase for warranty claims. For detailed terms and conditions, refer to the official Mackie webwebsted eller kontakt kundesupport.

8. Support og kontakt

For further assistance, technical support, or service inquiries regarding your Mackie HM-800, please visit the official Mackie website or contact their customer support department. You can typically find contact information, FAQs, and additional resources on their support pages.

9. Related Product Video