RGBZONE SP108E

RGBZONE SP108E WiFi LED Controller User Manual

Model: SP108E

1. Introduktion

The RGBZONE SP108E WiFi LED Controller is designed for controlling addressable LED strips and modules. It offers versatile control options via a smartphone application, supporting both IOS and Android devices. This controller is compatible with a wide range of LED driver ICs and provides numerous dynamic and static color modes to enhance your lighting experience.

RGBZONE SP108E WiFi LED Controller with included accessories

Image 1.1: The RGBZONE SP108E WiFi LED Controller, shown with the included 3-pin connector cable and screwdriver.

2. Pakkens indhold

Kontroller venligst, at alle nedenstående varer er til stede i din pakke:

  • 1 x RGBZONE SP108E WiFi LED Controller
  • 1 x 3PIN Connector Cable
  • 1 x skruetrækker
  • 1 x Brugermanual (dette dokument)

3. Specifikationer

FeatureDetalje
ModelSP108E
Input bindtageDC 5V~24V
Max Control Pixels2048 pixels
Max Wattage144W
KontrolmetodeWiFi (2.4G only), App Control (IOS 10.0+, Android 4.4+)
Understøttede IC'erWS2811, WS2812B, WS2801, SK6812, SK6812-RGBW, WS2813, LPD6803, LPD8806, APA102, TM1913, UCS1903, SM16703, DMX512, etc. (Does not support 5050RGB or RGBW LED strips without ICs)
Dimensioner85mm x 45mm x 23mm (Controller body)
DriftstilstandeAP (Access Point) Mode, STA (Station) Mode
Funktioner180 dynamic modes, 8 single color modes, 16 million static colors, color capture from image, adjustable brightness/speed, reverse connection protection, hot swap protection, save user settings.
Dimensions of the SP108E LED controller

Image 3.1: Physical dimensions of the SP108E WiFi LED Controller.

Diagram showing supported LED driver ICs and controller pinout

Image 3.2: List of compatible LED driver ICs and the pin assignments for the controller's output ports.

4. Opsætningsvejledning

4.1. Hardwareforbindelse

  1. Tilslut LED-strimmel: Identify the data (DAT), clock (CLK) if applicable, VCC, and GND pins on your addressable LED strip. Connect these to the corresponding output ports on the SP108E controller.
    • For single-wire ICs (e.g., WS2812B, WS2811, SK6812): Connect DAT, VCC, and GND. CLK is not used.
    • For two-wire ICs (e.g., WS2801, APA102, SK9822): Connect DAT, CLK, VCC, and GND.

    Vigtig: The color of the LED connector wire may not match the color of the controller's labels. Always distinguish GND, DAT, CLK, and VCC based on the LED strip's markings and the controller's labels.

  2. Tilslut strømforsyning: Connect a DC 5V-24V power supply to the controller's input. Ensure the voltage matcher kravene til din LED-strip.
    • Do not use a 12V or 24V power supply for a 5V LED strip.
    • The controller supports a wide voltage range (DC 5V-24V) and will automatically adapt.
Connection diagram for two-wire LED ICs like WS2801, APA102, SK9822Connection diagram for single-wire LED ICs like WS2812b, WS2811, SK6812

Billede 4.1: Eks.amples of wiring connections for different types of addressable LED strips.

Diagram illustrating that the power supply voltage must match the LED strip voltage

Image 4.2: Ensure the power supply voltage matches your LED strip's requirements.

4.2. App Installation

The SP108E controller is managed via the "LedShop" mobile application.

  1. Download app: Søg efter "LedShop" in the App Store (for IOS) or Google Play Store (for Android), or scan the QR code provided on the controller or in the product packaging.
  2. Kompatibilitet:
    • IOS version 10.0 or later is required.
    • Android OS version 4.4 or later is required.
Diagram showing app download instructions and connection overview

Image 4.3: Instructions for downloading the "LedShop" app and a general connection diagram.

5. Betjeningsvejledning

The SP108E controller supports two WiFi connection modes: AP Mode and STA Mode.

5.1. AP (Adgangspunkt) Tilstand

In AP Mode, the controller acts as its own WiFi hotspot, allowing your phone to connect directly to it. This mode is suitable for direct control without a router.

  1. Tænd: Power on the SP108E controller.
  2. Connect to Controller WiFi: On your smartphone, go to WiFi settings. Find and connect to the WiFi network named "SP108E_xxxx" (where xxxx is a unique identifier). The default password is "12345678".
  3. Open LedShop App: Launch the "LedShop" application. The app should automatically detect and connect to the controller.
  4. Rename Controller (Optional): You can long-press the connected device in the app to rename it for easier identification.

5.2. STA (Station) Mode

In STA Mode, the controller connects to your existing 2.4G WiFi network, allowing you to control it from anywhere within your network, or even remotely if your router supports it. This mode requires a 2.4G WiFi network; 5G networks are not supported.

  1. Connect via AP Mode First: Initially, connect your phone to the controller in AP Mode as described above.
  2. Configure STA Mode in App: Within the "LedShop" app, navigate to the settings or WiFi configuration section. Select your home 2.4G WiFi network from the list and enter its password.
  3. Bekræft forbindelse: The controller will attempt to connect to your router. Once connected, the controller's WiFi network ("SP108E_xxxx") will disappear, and your phone can reconnect to your home WiFi network. The app will then find the controller on your LAN.

Note: If the device fails to connect to your WiFi network within 20 seconds, it will revert to AP Mode. You may need to repeat the steps.

5.3. App Features and Settings

Once connected, the "LedShop" app provides comprehensive control over your LED lighting:

  • Valg af tilstand: Choose from 180 multi-color dynamic modes or 8 single-color dynamic modes.
  • Statiske farver: Access 16 million static color options.
  • Justering af lysstyrke og hastighed: Adjust the brightness and speed of dynamic effects.
  • Farveoptagelse: Use the "from-image-to-effect" function to capture colors from an image and apply them to your LEDs.
  • Pixel & Segment Settings: Configure the total number of pixels and segments to ensure correct display for your specific LED strip. The controller supports up to 2048 pixels.
  • IC Type Selection: Select the correct LED driver IC type for your strip (e.g., WS2812B, APA102).
  • Gem indstillinger: User settings are automatically saved when power is off.
Screenshots of the LedShop app interface showing various color modes and settings

Billede 5.1: Eks.amples of the "LedShop" app interface, demonstrating mode selection, color wheels, and customization options.

Detailed app screenshots showing connection steps, renaming, IC type selection, pixel settings, and various effects

Image 5.2: Comprehensive guide to app usage, including connection modes, settings, and effect customization.

6. Vedligeholdelse

  • Rensning: Brug en tør, blød klud til at rengøre controlleren. Brug ikke flydende rengøringsmidler eller aerosoler.
  • Miljø: This device is designed for indoor use only. Avoid exposure to moisture, extreme temperatures, and direct sunlight.
  • Forbindelser: Kontrollér regelmæssigt alle ledningsforbindelser for at sikre, at de er sikre og fri for skader.
  • Firmwareopdateringer: Check the "LedShop" app or RGBZONE's official website for any available firmware updates for the controller to ensure optimal performance and new features.

7. Fejlfinding

ProblemMulig årsagLøsning
Controlleren tænder ikke.Ingen strømforsyning, forkert lydstyrketage, faulty power supply.Ensure power supply is connected and functional. Verify voltage matches LED strip requirements (DC 5V-24V).
Cannot connect to controller WiFi (AP Mode).Incorrect password, controller not in AP mode, 5G WiFi interference.Default password is "12345678". Power cycle the controller to force AP mode. Ensure your phone is using 2.4G WiFi.
Controller fails to connect to home WiFi (STA Mode).Incorrect WiFi password, 5G WiFi network, controller too far from router.Double-check WiFi password. Ensure your router is broadcasting a 2.4G network. Move controller closer to the router.
LEDs not lighting up or displaying incorrect colors/patterns.Incorrect wiring (DAT, CLK, VCC, GND), wrong IC type selected in app, incorrect pixel count, faulty LED strip.Verify all wiring connections are correct. Select the exact IC type of your LED strip in the app. Set the correct number of pixels. Test with a known working LED strip if possible.
Controller does not respond to app commands.No WiFi connection, app not properly synced, controller frozen.Ensure your phone is connected to the controller (AP Mode) or the same home WiFi network (STA Mode). Close and reopen the app. Power cycle the controller.

8. Garanti og support

For warranty information and technical support, please refer to the RGBZONE official website or contact their customer service directly. Details are typically available on the product packaging or the brand's online presence.

Fabrikant: RGBZONE

Modelnummer: SP108E / 4334417650

Dato først tilgængelig: 29. juni 2018

© 2023 RGBZONE. All rights reserved.

For mere information, besøg RGBZONE Store on Amazon