1. Introduktion
This manual provides essential information for the installation, operation, and maintenance of the Black Box LPH008A-R2 Extreme PoE+ Switch. Please read this manual thoroughly before operating the device to ensure proper functionality and safety.
The Black Box LPH008A-R2 is a hardened Gigabit PoE+ switch designed for robust performance in demanding environments. It features eight 10/100/1000-Mbps RJ-45 ports with Power over Ethernet (PoE+) capabilities, compliant with 802.3at standards.
2. Sikkerhedsoplysninger
- Sørg for korrekt jordforbindelse af enheden.
- Do not expose the switch to moisture or extreme humidity.
- Use only the specified power supply. Incorrect voltage kan beskadige enheden.
- Undgå at blokere ventilationsåbningerne for at forhindre overophedning.
- Afbryd strømmen før rengøring eller servicering af enheden.
- Installation skal udføres af kvalificeret personale.
3. Pakkens indhold
Bekræft at alle varer er til stede i pakken:
- Black Box LPH008A-R2 Extreme PoE+ Switch
- Dokumentation (denne brugermanual)
- Power terminal block (pre-installed or included)
Note: Power supply unit may be sold separately depending on the specific product bundle.
4. Produktet er slutview
4.1 Frontpanel
The front panel of the LPH008A-R2 switch features the network ports and LED indicators.
Figur 1: Front Panel of Black Box LPH008A-R2 Switch.
This image displays the front panel of the Black Box LPH008A-R2 switch. It features eight 10/100/1000T RJ45 ports, numbered 1 through 8. Above the ports are LED indicators for P1, P2 (power inputs), and Fault. A green terminal block for power input is visible at the top.
4.2 LED-indikatorer
| Indikator | Status | Beskrivelse |
|---|---|---|
| P1 / P2 | Til (grøn) | Power input 1 / Power input 2 is active. |
| Fejl | På (rød) | System fault detected. |
| Port LEDs (Green) | On | Link established at 1000 Mbps. |
| Blinker | Data activity at 1000 Mbps. | |
| Port LEDs (Amber) | On | Forbindelse etableret ved 10/100 Mbps. |
| Blinker | Data activity at 10/100 Mbps. |
5. Opsætning og installation
5.1 Strømtilslutning
- Ensure the power source is turned off before connecting.
- Connect the 12-57 VDC power supply to the terminal block at the top of the switch. The switch supports dual power inputs (P1 and P2) for redundancy.
- Tighten the screws on the terminal block to secure the power wires.
- Turn on the power source. The P1 and/or P2 LED indicators should illuminate green.
5.2 Netværksforbindelse
- Connect standard RJ45 Ethernet cables from your network devices (e.g., computers, IP cameras, wireless access points) to any of the 8 RJ45 ports on the switch.
- For PoE-powered devices, ensure they are 802.3at compliant. The switch will automatically detect and provide power.
- Observe the port LEDs. A solid green or amber light indicates a successful link. Flashing indicates data activity.
5.3 Montering (valgfrit)
The LPH008A-R2 is designed for industrial environments and can be DIN-rail mounted or wall-mounted. Refer to the specific mounting kit instructions for detailed steps.
6. Betjeningsvejledning
The Black Box LPH008A-R2 is an unmanaged switch, meaning it operates automatically without requiring configuration. Once powered on and connected, it will forward Ethernet traffic between connected devices.
- Opstart: After connecting power, the switch will initiate. The P1/P2 LEDs will light up.
- Dataoverførsel: Connect network devices to the RJ45 ports. The switch automatically detects link speed (10/100/1000 Mbps) and duplex mode.
- PoE+ funktionalitet: For PoE-enabled devices, the switch provides up to 30 watts per port, with a total power budget of 60 Watts (12-24 VDC input) or 120 Watts (24-57 VDC input).
7. Vedligeholdelse
- Rensning: Brug en blød, tør klud til at rengøre ydersiden af kontakten. Brug ikke flydende rengøringsmidler eller rengøringsmidler på sprayform.
- Ventilation: Sørg for, at ventilationsåbningerne er fri for støv og snavs for at opretholde korrekt luftgennemstrømning.
- Firmware: Som en ikke-administreret switch er firmwareopdateringer typisk ikke nødvendige eller tilgængelige.
- Miljøforhold: Operate the switch within its specified temperature range (-40 to +75° C) and humidity levels.
8. Fejlfinding
8.1 Ingen strøm
- Check if the power supply is correctly connected to the terminal block.
- Kontroller, at strømkilden er aktiv og leverer den korrekte lydstyrke.tage (12-57 VDC).
- Ensure the P1/P2 LEDs are illuminated. If not, check the power supply and connections.
8.2 Intet link på porten
- Sørg for, at Ethernet-kablet er korrekt tilsluttet i begge ender.
- Prøv et andet Ethernet-kabel.
- Connect a different device to the port to rule out issues with the connected device.
- Kontroller status for den tilsluttede enhed.
8.3 PoE-enhed modtager ikke strøm
- Verify that the connected device is PoE (802.3at) compliant.
- Ensure the total power budget of the switch is not exceeded.
- Tjek kablet for skader.
8.4 Fault LED is On
- A red Fault LED indicates a system error. Disconnect power, wait a few seconds, and reconnect.
- If the fault persists, contact technical support.
9. Specifikationer
| Feature | Detalje |
|---|---|
| Modelnummer | LPH008A-R2 |
| Antal havne | 8 x 10/100/1000-Mbps RJ45 |
| PoE Standard | IEEE 802.3at (PoE+) |
| PoE-strømudgang | Op til 30W pr. port |
| Samlet strømbudget | 60W (12-24 VDC input), 120W (24-57 VDC input) |
| Input bindtage | Dual 12-57 VDC |
| Driftstemperatur | -40 til +75° C (-40 til +167° F) |
| Bedømmelse af kabinet | IP30 |
| Dimensioner (LxBxH) | 1.61 x 3.74 x 5.67 tommer (4.09 x 9.5 x 14.4 cm) |
| Vægt | 1.8 pund (0.82 kg) |
| Etui materiale | Kobber |
10. Garanti og support
Black Box products are designed for reliability and performance. For specific warranty details, please refer to the warranty information provided with your purchase or visit the official Black Box webwebsted.
For technical assistance or support, please contact Black Box customer service. Contact information can typically be found on the Black Box webwebstedet eller i din produktdokumentation.
Webwebsted: www.blackbox.com