DS18 SLC-X1650.2 Select Series 2 Channel Class AB Amplivligere brugervejledning

1. Introduktion

Thank you for choosing the DS18 SLC-X1650.2 Select Series 2 Channel Class AB Amplifier. Det her amplifier is designed to provide high-quality audio performance for your vehicle's sound system. To ensure proper installation and operation, please read this manual thoroughly before beginning. Keep this manual for future reference.

2. Sikkerhedsinstruktioner

• Always disconnect the vehicle's battery negative terminal before installing or servicing any car audio components.
• Sørg for, at alle ledninger er korrekt ført og fastgjort for at forhindre skader eller kortslutninger.
• Brug passende ledningsføring til strøm-, jord- og højttalertilslutninger som angivet i denne manual.
• Monter ampOpbevar køleren sikkert på et sted, der giver tilstrækkelig ventilation og er beskyttet mod fugt og overdreven varme.
• If you are unsure about any part of the installation process, seek assistance from a professional car audio installer.
• Betjen ikke amphvis den er beskadiget eller ikke fungerer korrekt.

3. Pakkens indhold

Pakken skal indeholde følgende varer:

• DS18 SLC-X1650.2 Amplivligere
• Brugermanual

4. Funktioner

• 2-kanals klasse AB Amplifier design.
• Capable of handling a wide range of speaker impedances (2-8 Ohm).
• Full-range audio amplification, suitable for midranges, tweeters, and coaxial speakers.
• Adjustable Low Pass Filter (LPF) and High Pass Filter (HPF) for precise sound tuning.
• Selectable Bass Boost levels (0dB, +6dB, +12dB).
• Robust construction for durability and reliable performance.

5. Installation

5.1 Montering af Amplivligere

Vælg et tørt, godt ventileret og sikkert monteringssted. Undgå at montere amplifier directly on carpet or in enclosed spaces that restrict airflow. Ensure there is enough space around the ampvarmeafledning til korrekt varmeafledning.

Sikre den amplifier using the provided mounting hardware. Mark the mounting holes, drill pilot holes if necessary, and fasten the amplifier firmly to the mounting surface.

5.2 Ledningsforbindelser

Proper wiring is crucial for optimal performance and safety. Refer to the diagrams below for correct connections.

Billede 1: View of the DS18 SLC-X1650.2 amplifier showing the power input terminals (GND, REM, +12V), fuse holder, and speaker output terminals (R+, R-, B+, B-).

Strømforbindelser:

• +12V (strøm): Connect this terminal directly to the positive (+) terminal of the vehicle's battery using a heavy-gauge power cable. An in-line fuse (not supplied, but the amplifier has a 35A fuse) should be installed within 18 inches of the battery.
• GND (jord): Connect this terminal to a clean, unpainted metal surface on the vehicle's chassis. Ensure a good electrical connection by scraping away any paint or rust. Use a heavy-gauge ground cable of the same size as the power cable, and keep it as short as possible.
• REM (fjerntænding): Connect this terminal to the remote turn-on output of your head unit. This wire turns the amptænd og sluk for højttaleren med din bils lydsystem.

Højttalerforbindelser:

Connect your speakers to the "SPEAKER OUTPUT" terminals. Ensure correct polarity (+ to + and - to -) for each speaker. This amplifier supports 2-channel stereo or bridged mono configurations.

• Stereo-tilstand: Connect one speaker to R+ and R- for the right channel, and another speaker to B+ and B- for the left channel.
• Brokoblet tilstand: For a single subwoofer or higher power output, connect the speaker across R+ and B-. Refer to the diagram on the amplifier for bridged wiring. The minimum impedance for bridged operation is 4 Ohms.

Billede 2: View of the DS18 SLC-X1650.2 amplifier showing the input and control panel, including High Input, Line Out, Gain, Bass Boost, HPF, and LPF controls.

Lydindgangsforbindelser:

• RCA Input (LINE IN): Tilslut RCA-kabler fra din hovedenheds for-amp udgange til amplifier's LINE IN jacks.
• High-Level Input (HIGH INPUT): If your head unit does not have RCA outputs, use the high-level input. Connect the speaker wires from your head unit to the HIGH INPUT connector.
• RCA Output (LINE OUT): These RCA outputs allow you to pass the audio signal to another amplifier i dit system.

6. Betjening og justeringer

The DS18 SLC-X1650.2 ampLifier har adskillige kontroller til finjustering af dit lydsystem:

• GAIN (indgangsfølsomhed): Denne kontrol passer til amplifier's input sensitivity to the output level of your head unit. Adjust it to prevent distortion. Start with the gain at minimum and slowly increase it until you hear distortion, then back off slightly.
• BASS BOOST: Provides an adjustable bass enhancement at 0dB, +6dB, or +12dB. Use sparingly to avoid distortion.
• HPF (Højpasfilter): This filter allows frequencies above the set point to pass through to the speakers. Useful for protecting smaller speakers from low bass frequencies. Adjustable from 50Hz to 1.2KHz.
• LPF (lavpasfilter): This filter allows frequencies below the set point to pass through to the speakers. Typically used for subwoofers. Adjustable from 50Hz to 200Hz.
• CROSSOVER Switch: Select between HPF, FULL (full range), or LPF operation.

7. Betjeningsvejledning

Når amplifier is correctly installed and all connections are secure:

1. Tænd for bilens tænding og hovedenhed. ampApparatet bør tænde automatisk via fjerntændingsledningen.
2. Start med ampLifierens forstærkningskontrol ved dens minimumsindstilling.
3. Afspil et velkendt musikstykke med moderat lydstyrke på din hovedenhed.
4. Langsomt øge amplifier's gain control until you hear any audible distortion, then reduce it slightly until the sound is clear.
5. Adjust the HPF, LPF, and Bass Boost settings to achieve your desired sound balance.
6. Avoid setting the gain too high, as this can lead to distorted audio and potential damage to your speakers or amplivligere.

8. Vedligeholdelse

The DS18 SLC-X1650.2 ampLifier kræver minimal vedligeholdelse:

• Kontrollér regelmæssigt alle ledningsforbindelser for at sikre, at de er fastgjorte og fri for korrosion.
• Behold ampFjerneren er ren og fri for støv og snavs. Brug en blød, tør klud til rengøring.
• Sørg for ampAt køleribberne ikke er blokerede for at opretholde korrekt varmeafledning.
• Hvis sikringen springer, må den kun udskiftes med en sikring af samme type og kapacitet (35A).

9. Fejlfinding

10. Specifikationer

11. Produktet er slutview Video

12. Garanti og support

For garantioplysninger og teknisk support henvises til den officielle DS18 webwebstedet eller kontakt deres kundeservice direkte. Gem din købskvittering som købsbevis i tilfælde af garantikrav.

For yderligere hjælp, besøg DS18 Butik på Amazon.