1byone Wireless Driveway Alert System Instruction Manual

Produkt overview

The 1byone Wireless Driveway Alert System provides a solution to detect movement and alert you when someone enters your property. This system includes one infrared motion sensor and two plug-in receivers. When motion is detected, the Passive Infrared (PIR) sensor transmits a wireless signal to the receiver, which then alerts you via a chime, alarm tone, or silent LED flash.

Figure 1: 1byone Wireless Driveway Alert System components.

Kassens indhold

• 1 x PIR Transmitter (Infrared Motion Sensor)
• 2 x Receivers (Plug-in Units)
• 1 x Brugsanvisning (dette dokument)
• 4 x Vægstik
• 4 x skruer

Opsætningsinstruktioner

1. Install Batteries in PIR Sensor

The PIR Transmitter requires 3 x 1.5V AAA batteries (not included). Open the battery compartment on the back of the sensor and insert the batteries, ensuring correct polarity.

Figure 2: PIR Sensor battery installation. Insert 3 x 1.5V AAA alkaline batteries (not included).

2. Power On the Receivers

Plug each receiver into a standard AC power outlet. The receivers can also be powered by 3 x 1.5V C batteries (not included) for portable use.

3. Pairing the Sensor and Receivers (Code Match)

The sensor and receivers are typically pre-paired. If pairing is needed or if you are adding additional sensors/receivers:

1. Sørg for, at modtageren er tændt.
2. Press the "Code match button" on the receiver (refer to Figure 3 for location). The receiver will enter pairing mode, indicated by an LED flash or sound.
3. Wave your hand in front of the PIR sensor to trigger it.
4. The receiver will confirm successful pairing with a chime or LED flash. Repeat this process for each receiver.

Figure 3: Receiver controls, including the Code match button.

4. Mounting the PIR Sensor

Select a suitable location for the PIR sensor. Use the provided wall plugs and screws to securely mount the sensor. Consider the following for optimal performance and to avoid false alarms:

• Undgå direkte sollys: Do not mount the sensor in direct sunlight, as moving heat sources can trigger the PIR.
• Protected Location: When installing outdoors, choose a shady, protected place with minimal temperature fluctuations.
• Væsentlige overvejelser: Avoid mounting on UPVC or metal doorframe surfaces, which may reduce the wireless transmission range.
• Registreringsområde: The motion detecting range is 5-8 meters (16-26 feet). Position the sensor to cover the desired area effectively.

Figur 4: Eksample of PIR sensor mounting in a sheltered area.

Betjeningsvejledning

Modtager kontrol

Refer to Figure 3 for the location of the following controls on the receiver:

• Lydstyrke knap: Press to adjust the receiver's alert volume.
• Melody Selector: Press to cycle through the available chime melodies. There are 36 chime tones.
• Bell-and-LED Switch: This switch allows you to select the alert mode:
  • Chime/Alarm + LED: The receiver will sound a chime or alarm and flash its LED when motion is detected.
  • Silent LED Flash Only: The receiver will only flash its LED, providing a silent alert. This is useful for environments where sound alerts are not desired, such as for napping children or individuals with hearing impairments.

Detection and Alert

When the PIR sensor detects motion within its 5-8 meter (16-26 feet) range, it sends a wireless signal to the paired receiver(s). The receiver(s) will then activate according to the selected alert mode (chime/alarm, LED flash, or both).

The operating range between the sensor and receiver is up to 100 meters (328 feet) in open areas. Environmental factors and obstacles may affect this range. The receiver can pair with up to 50 sensors.

Figure 5: System features and operating range illustration.

Opretholdelse

Udskiftning af batteri

Replace the 3 x AAA batteries in the PIR sensor when the detection range decreases or the sensor stops transmitting signals reliably. Always use fresh alkaline batteries for optimal performance.

Rensning

Wipe the sensor and receiver with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these may damage the units.

Fejlfinding

• No Detection or Reduced Range:
  • Check PIR sensor batteries and replace if necessary.
  • Ensure the sensor is not mounted on UPVC or metal surfaces.
  • Verify the sensor and receiver are within the 100m (328ft) operating range.
  • Minimize obstacles between the sensor and receiver.
  • Re-pair the sensor and receiver (refer to "Pairing the Sensor and Receiver" section).
• Falske alarmer:
  • Relocate the PIR sensor away from direct sunlight or areas with rapid temperature changes (e.g., near vents, large reflective surfaces).
  • Ensure the sensor is not in a location affected by strong winds that could move objects within its detection zone.
  • Adjust the sensor's angle to avoid detecting unwanted movement (e.g., small animals).
• Modtageren svarer ikke:
  • Ensure the receiver is properly plugged into a working power outlet or has fresh C batteries installed.
  • Check if the sensor's batteries are depleted.
  • Attempt to re-pair the sensor and receiver.

Specifikationer

Garanti og support

This 1byone product is covered by a 24 måneders garanti from the date of purchase. For any issues or support inquiries, please refer to the contact information provided with your purchase documentation or visit the official 1byone webwebsted.