LASCO 24V Heat Only Thermostat

White Rodgers 24V Heat Only Thermostat Instruction Manual

Model: 24V Heat Only Thermostat

1. Introduktion

This manual provides comprehensive instructions for the installation, operation, and maintenance of your White Rodgers 24V Heat Only Thermostat. This device is designed to control heating systems by maintaining a desired temperature within a range of 50 to 90 degrees Fahrenheit (10 to 32 degrees Celsius). Please read these instructions carefully before proceeding with installation or operation to ensure safe and efficient use.

2. Sikkerhedsoplysninger

Overhold altid følgende sikkerhedsforanstaltninger:

  • Elektrisk fare: Disconnect power to the heating system at the main fuse or circuit breaker panel before installing or servicing the thermostat. Failure to do so may result in electrical shock or equipment damage.
  • Voltage Kompatibilitet: This thermostat is designed for 24V heating systems only. Do not use it with line voltage (120V or 240V) systems.
  • Professionel installation: If you are unfamiliar with electrical wiring, it is recommended to have a qualified electrician or HVAC technician install this thermostat.
  • Korrekt bortskaffelse: Dispose of old thermostats and packaging materials according to local regulations.

3. Installation og opsætning

Følg disse trin for korrekt installation:

3.1 Monteringssted

Install the thermostat on an inside wall, approximately 5 feet (1.5 meters) above the floor. Avoid locations:

  • Near windows, outside doors, or vents.
  • Near heat-generating appliances (e.g., televisions, lamps, refrigerators).
  • In direct sunlight or areas with poor air circulation.

3.2 Ledningsføring

Before wiring, ensure power to the heating system is OFF.

  1. Remove the cover of the old thermostat and note the wire connections. Typically, a heat-only system will have two wires: 'R' (power) and 'W' (heat call).
  2. Disconnect the wires from the old thermostat.
  3. Mount the new White Rodgers thermostat base to the wall using the provided screws.
  4. Connect the 'R' wire to the 'R' terminal and the 'W' wire to the 'W' terminal on the new thermostat. Ensure connections are secure.
  5. Sæt termostatdækslet på igen.

3.3 Indledende opstart

Restore power to the heating system at the main fuse or circuit breaker panel. The thermostat is now ready for operation.

White Rodgers Heat Only Thermostat with temperature dial and OFF/ON switch

Figur 1: Front view of the White Rodgers Heat Only Thermostat. The upper slider controls the OFF/ON function, while the lower slider sets the desired temperature, indicated in both Fahrenheit (50-90) and Celsius (10-32).

4. Betjeningsvejledning

The White Rodgers Heat Only Thermostat features simple manual controls.

4.1 Strømstyring

The upper slider on the thermostat controls the power to the heating system:

  • Skub til SLUKKET: Disables the heating system.
  • Skub til ON: Enables the heating system to operate based on the set temperature.

4.2 Indstilling af temperaturen

The lower slider on the thermostat is used to set your desired room temperature:

  1. Ensure the upper slider is set to ON.
  2. Move the lower slider to the desired temperature setting. The scale indicates temperatures in both Fahrenheit (50-90°F) and Celsius (10-32°C).
  3. The heating system will activate when the room temperature falls below your set point and will turn off when the room temperature reaches or exceeds your set point.

5. Vedligeholdelse

This thermostat requires minimal maintenance.

  • Rensning: Tør termostatens yderside regelmæssigt af med en blød klud.amp klæde. Brug ikke slibende rengøringsmidler eller opløsningsmidler.
  • Fjernelse af støv: Gently remove any dust accumulation from the vents or internal components using a soft brush or compressed air. Ensure power is off before cleaning internal components.
  • This model does not require battery replacement as it is a mechanical, 24V wired thermostat.

6. Fejlfinding

If you encounter issues with your thermostat, refer to the following table:

ProblemMulig årsagLøsning
Ingen varme
  • Thermostat set to OFF.
  • Temperaturen er indstillet for lavt.
  • Sprunget sikring eller udløst afbryder.
  • Løse ledninger.
  • Fejlfunktion i varmesystemet.
  • Set thermostat to ON.
  • Increase set temperature above room temperature.
  • Check and replace fuse or reset breaker.
  • Check wiring connections (ensure power is OFF).
  • Contact an HVAC technician.
Unøjagtig temperaturaflæsning
  • Termostatens placering påvirkes af træk eller varmekilder.
  • Støvophobning.
  • Relocate thermostat if possible, or shield from drafts/heat sources.
  • Clean thermostat (ensure power is OFF).
Heating system runs continuously
  • Termostat indstillet for højt.
  • Termostat fejlfunktion.
  • Lavere indstillet temperatur.
  • If problem persists, contact an HVAC technician.

7. Specifikationer

  • Mærke: White Rodgers (Manufactured by LASCO)
  • Model: 24V Heat Only Thermostat
  • Voltage: 24 volt
  • Strøm: 1.2 Amps
  • Temperaturområde: 50 til 90°F (10 til 32°C)
  • Skærmtype: Manual Slider
  • Kontroltype: Button Control (Slider)
  • Baggrundsbelysning: Ingen
  • Dimensioner: Approximately 20 x 7 x 8.8 inches (Product packaging dimensions, actual unit smaller)
  • Varens vægt: 6.4 ounce
  • UPC: 786710545658

8. Garanti og support

Specific warranty information for this White Rodgers thermostat is not provided in the product details. For warranty claims or technical support, please refer to the contact information provided with your purchase or visit the official White Rodgers webwebsted. Gem din købsbevis til eventuelle garantirelaterede spørgsmål.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.