1. Introduktion og overview
The Draminski Hay & Straw High-Moisture Meter with Probe Plus Temperature Display is a precision instrument designed for accurate measurement of moisture content in hay and silage, as well as displaying temperature. This manual provides essential information for the proper setup, operation, maintenance, and troubleshooting of your device to ensure reliable performance and longevity.
Figure 1: Draminski Hay & Straw High-Moisture Meter. The image shows the yellow main unit with a digital display, connected to a long metal probe and a separate yellow handle for stability during measurement.
2. Produktfunktioner
- Designed for Hay & Silage High-Moisture Measurement.
- Moisture Range: 10-80%.
- Functions include Minimum, Maximum, and Average readings.
- Temperature Display in Degrees Fahrenheit.
- Large Number LCD for easy reading.
- Probe Length: 22 Inches (56 cm).
- Powered by one 9 Volt Battery.
3. Sikkerhedsoplysninger
Læs og forstå alle sikkerhedsinstruktioner, før du bruger apparatet. Undladelse af at gøre dette kan medføre personskade eller beskadigelse af måleren.
- Håndtering af sonde: The probe is sharp. Handle with care to prevent injury. Keep out of reach of children.
- Elektrisk sikkerhed: Do not expose the meter or probe to excessive moisture or liquids beyond its intended use. Avoid using the device in wet conditions that could compromise electrical components.
- Batterisikkerhed: Use only the specified battery type (9V). Ensure correct polarity when installing. Do not mix old and new batteries. Remove batteries if the device will not be used for an extended period to prevent leakage.
- Opbevaring: Opbevar måleren et tørt, køligt sted, væk fra direkte sollys og ekstreme temperaturer.
4. Opsætning
4.1. Batteriinstallation
- Find batterirummet på bagsiden af hovedenheden.
- Åbn batterirummets dæksel.
- Insert one 9V battery, ensuring the correct polarity (+/-) as indicated inside the compartment.
- Luk batterirummets dæksel forsvarligt.
4.2. Tilslutning af sonde
The probe is typically pre-connected. If it needs to be reconnected or checked:
- Sørg for, at måleren er slukket.
- Connect the probe cable securely into the designated port on the main meter unit.
- Ensure the handle is also securely attached to its respective port, if applicable.
5. Betjeningsvejledning
5.1. Tænd/sluk
- For at tænde måleren skal du trykke på MAGT button. The LCD will illuminate and display the current reading or a default screen.
- For at slukke måleren skal du trykke på og holde nede MAGT button until the display turns off. The meter may also have an auto-off feature to conserve battery life.
5.2. Taking a Moisture Measurement
- Sørg for, at måleren er tændt.
- Carefully insert the probe into the hay or silage bale. For best results, insert the probe deeply into the material, ensuring good contact.
- The moisture content will be displayed on the LCD screen. Allow a few seconds for the reading to stabilize.
- Take multiple readings in different locations within the bale for a more representative average.
5.3. Using MIN/MAX/AVG Functions
The meter is equipped with functions to display the minimum, maximum, and average moisture readings taken during a session.
- Tryk på MIN button to display the lowest moisture reading recorded.
- Tryk på MAKS button to display the highest moisture reading recorded.
- Tryk på AVG button to display the average of all moisture readings taken.
- Consult the meter's specific button labels for exact function activation.
5.4. Temperaturvisning
In addition to moisture, the meter can display the temperature of the material. This reading is typically shown alongside the moisture content or can be toggled using a dedicated button (refer to your meter's specific controls).
- The temperature is displayed in Degrees Fahrenheit.
6. Vedligeholdelse
6.1. Rensning
- After each use, wipe the probe clean with a dry cloth to remove any residue.
- Do not use abrasive cleaners or solvents on the meter or probe.
- Keep the display and buttons free from dust and debris.
6.2. Udskiftning af batteri
When the battery indicator appears on the display or the meter fails to power on, replace the 9V battery following the instructions in Section 4.1.
6.3. Opbevaring
When not in use, store the meter and probe in a protective case (if provided) in a dry, cool environment. Avoid storing in areas with extreme temperature fluctuations or high humidity.
7. Fejlfinding
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Måleren tænder ikke. | Dødt eller forkert installeret batteri. | Udskift 9V-batteriet, og sørg for korrekt polaritet. |
| Unøjagtige eller svingende aflæsninger. | Poor probe contact with material; probe dirty; material too dense/loose. | Ensure probe is fully inserted and making good contact. Clean the probe. Take multiple readings. |
| Displayet viser "Err" eller en lignende fejlmeddelelse. | Measurement out of range; internal malfunction. | Ensure moisture content is within 10-80% range. If problem persists, contact support. |
8. Specifikationer
| Mærke | Draminski |
| Modelnummer | DSHMM |
| Fugtområde | 10-80 % |
| Probe Length | 22 tommer (56 cm) |
| Temperatur display | grader Fahrenheit |
| Temperatur nøjagtighed | 1.0 grader Fahrenheit |
| Lavere temperaturvurdering | 32 grader Fahrenheit |
| Øverste temperaturvurdering | 100 grader Fahrenheit |
| Strømkilde | Et 9V batteri |
| Varens vægt | 2.99 pund (1.36 kilo) |
| Pakkedimensioner | 28.14 x 6.4 x 3.7 tommer |
| Farve | Gul |
9. Garanti og support
The Draminski Hay & Straw High-Moisture Meter comes with a 2-års garanti fra købsdatoen, dækker defekter i materialer og udførelse ved normal brug.
For technical support, warranty claims, or service inquiries, please contact the manufacturer or your authorized dealer. Keep your purchase receipt as proof of purchase for warranty purposes.