Morris 85221 Decorative Dual F Connector Wall Plate User Manual

Indledning

This manual provides instructions for the installation, operation, and maintenance of the Morris 85221 Decorative Dual F Connector Wall Plate. This product is designed to provide a clean and organized connection point for two F-type coaxial cables, commonly used for cable television, satellite, or antenna signals. Please read these instructions carefully before installation to ensure proper and safe use.

Vigtige sikkerhedsoplysninger

ADVARSEL: Always disconnect power to the circuit at the main service panel before installing or servicing electrical components. Failure to do so may result in serious injury or death.

• Ensure all connections are secure to prevent signal loss or electrical hazards.
• Må ikke installeres i vådt eller damp steder, medmindre de specifikt er godkendt til sådanne miljøer.
• This product is intended for low-voltage coaxial cable applications. Do not connect to AC power lines.
• If you are unsure about any part of the installation process, consult a qualified electrician or technician.

Pakkens indhold

Kontroller, at alle komponenter er til stede, før installationen påbegyndes:

• 1 x Decorative Wall Plate (White)
• 1 x Dual F-Connector Jack Insert
• 2 x Mounting Screws (typically included with wall plates)

Note: Coaxial cables and tools for installation are sold separately.

Produktegenskaber

• Todelt design: The wall plate and F-connector jack are separate pieces, allowing for easier installation and removal for maintenance or painting without disconnecting cables.
• Dual F-Connectors: Provides two F-type coaxial connections for multiple devices or lines.
• Dekorativ finish: Flush design in white plastic for a clean aesthetic.
• Holdbart materiale: Constructed from UL94V-0 Flame Retardant Plastic for safety.
• Stik af høj kvalitet: Features 50 Micro Inches of Gold Plating for optimal signal integrity.
• Overholdelse: Meets FCC Requirements and complies with UL Standard 1863 and Article 800-51 of The National Electrical Code. UL/CSA Listed.

Specifikationer

Image: The Morris 85221 Dual F Connector Wall Plate shown with approximate dimensions (4.7 inches / 11 cm in height) for reference during installation planning.

Installationsvejledning

This section outlines the steps for installing your Morris 85221 Decorative Dual F Connector Wall Plate. Basic tools are required.

Nødvendige værktøjer:

• Skruetrækker (Phillips-skruetrækker anbefales)
• Wire Strippers/Crimpers (if terminating new coaxial cables)
• Coaxial Cable (RG6 or RG59, as appropriate)
• Existing low-voltage mounting bracket or electrical box (not included)

Trin-for-trin installation:

1. Forbered placeringen: Ensure you have an existing low-voltage mounting bracket or electrical box installed in the wall where you intend to place the wall plate. If not, install one according to local electrical codes.
2. Route Coaxial Cables: Pull the necessary coaxial cables through the mounting bracket or electrical box opening. Ensure there is enough slack to comfortably work with the cables.
3. Terminate Cables (if necessary): If your coaxial cables are not already terminated with F-connectors, use appropriate tools to strip the cable and crimp F-connectors onto the ends. Ensure a clean, secure connection.
4. Connect Cables to Jack Insert: Take the dual F-connector jack insert. Screw the F-connectors from your coaxial cables onto the back of the jack insert. Hand-tighten them securely.
   

   Image: The Morris 85221 Dual F Connector Wall Plate, showing the two F-type connectors on the front. The coaxial cables connect to the corresponding F-type ports on the rear of the insert.

5. Insert Jack into Wall Plate: The dual F-connector jack insert is designed to snap or fit securely into the opening of the decorative wall plate. Gently push the insert into the plate until it is flush and stable.
6. Monter vægpladen: Carefully push the assembled wall plate and jack insert into the mounting bracket or electrical box, guiding the cables into the wall cavity. Align the screw holes on the wall plate with those on the mounting bracket.
7. Secure the Wall Plate: Use the provided mounting screws to secure the wall plate to the mounting bracket. Do not overtighten, as this can crack the plastic plate.
8. Endelig kontrol: Ensure the wall plate is flush against the wall and all connections are secure. You can now connect your devices (TV, modem, etc.) to the front F-connectors.

For optimal signal quality, avoid sharp bends in coaxial cables and ensure all connections are tight.

Operation

The Morris 85221 Decorative Dual F Connector Wall Plate functions as a passive pass-through for coaxial signals. Once installed, simply connect your F-type coaxial cables from your devices (e.g., television, cable modem, satellite receiver) to the F-connector ports on the front of the wall plate. The plate provides a stable and organized connection point, ensuring signal integrity between your in-wall cabling and external devices.

Opretholdelse

The Morris 85221 Wall Plate requires minimal maintenance.

• Rensning: To clean the surface of the wall plate, use a soft, damp cloth. Avoid abrasive cleaners or solvents, as these may damage the plastic finish.
• Tilslutningskontrol: Periodically check the F-connector connections for tightness to ensure optimal signal quality. Loose connections can lead to signal degradation.
• Inspektion: Inspect the wall plate for any signs of damage or wear. If damage is observed, replace the unit to maintain safety and performance.

Fejlfinding

If you experience issues with your coaxial connection, consider the following:

If issues persist after troubleshooting, contact a qualified technician or your service provider.

Garanti og support

Morris Products stands behind the quality of its products. For specific warranty information, please refer to the documentation included with your purchase or visit the official Morris Products website. For technical support or inquiries, please contact Morris Products customer service.

Kontaktoplysninger for Morris Products: (Typically found on product packaging or manufacturer's webwebsted)

• Webwebsted: www.morrisproducts.com (Eksamplinket, verificér det faktiske webwebsted)
• Telefon: Refer to manufacturer's webhjemmeside for aktuelle kontaktnumre.