National Specialty Lighting XTL-1-HW/WH Xenon Under Cabinet Light Manual

Indledning

This manual provides detailed instructions for the installation, operation, and maintenance of your National Specialty Lighting XTL-1-HW/WH Xenon Under Cabinet Light. Please read all instructions carefully before beginning installation and retain this manual for future reference.

Vigtige sikkerhedsinstruktioner

• Læs alle instruktioner: Ensure you understand all steps before installation or operation.
• Kun indendørs brug: This fixture is designed for dry, indoor locations. Do not install in wet or damp miljøer.
• Afbryd strømmen: Always disconnect power at the circuit breaker before installing, servicing, or replacing bulbs.
• Uddannet elektriker: Installation should be performed by a qualified electrician or a person familiar with electrical wiring.
• Korrekt jordforbindelse: Sørg for, at armaturet er korrekt jordforbundet for at undgå elektrisk stød.
• Voltage: This fixture operates on 120V AC input, converting to 12V for the Xenon bulb.
• Pæretype: Use only the specified 18W T5 Wedge 12V Xenon bulb.

Pakkens indhold

Kontroller, at alle komponenter er til stede, før installationen påbegyndes:

• XTL-1-HW/WH Under Cabinet Light Fixture (1)
• 18W T5 Wedge 12V Xenon Bulb (1)
• Push-in Connectors (for wiring)
• Monteringshardware (skruer)
• Instruktionsmanual (dette dokument)

Opsætning og installation

Værktøj påkrævet

• Skruetrækker (Phillips og/eller flad)
• Trådstrippere
• Drill (if pre-drilling pilot holes)
• Blyant
• Målebånd

Montering af armaturet

1. Sluk for strømmen: Locate the circuit breaker controlling the area where the light will be installed and turn off the power. Verify power is off using a voltage tester.
2. Bestem placering: Choose a suitable location under a cabinet, ensuring adequate clearance and access for wiring. The fixture dimensions are 9" L x 4.63" W x 1.25" H.
3. Markér monteringspunkter: Hold the fixture in the desired position and mark the mounting screw locations with a pencil.
4. Sikker beslag: Using the provided mounting screws, attach the fixture securely to the underside of the cabinet.

Electrical Connection (Hardwire)

1. Forbered ledningsføring: Route the 120V AC supply wires to the fixture's wiring compartment. Strip approximately 1/2 inch of insulation from the ends of the supply wires (black, white, ground).
2. Tilslut ledninger: Use the provided push-in connectors to connect the fixture's wires to the supply wires:
   • Tilslut sort (hot) wire from the supply to the sort armaturets ledning.
   • Tilslut hvid (neutral) wire from the supply to the hvid armaturets ledning.
   • Tilslut grøn (ground) wire from the supply to the grøn or bare copper wire of the fixture.
3. Sikre forbindelser: Ensure all connections are tight and secure. Tuck wires neatly into the wiring compartment.
4. Install bulb: Gently insert the 18W T5 Wedge 12V Xenon bulb into the fixture's socket. Avoid touching the glass portion of the bulb with bare hands.
5. Close diffuser: Close the frosted glass diffuser lens. It features a simple hinged push-to-open mechanism.
6. Genopret strøm: Tænd for strømmen igen ved afbryderen.

Figur 1: Overview of the National Specialty Lighting XTL-1-HW/WH Xenon Under Cabinet Light, showing its compact design and key dimensions (Length: 9 inches, Width: 4.63 inches, Height: 1.25 inches). The image also highlights the frosted glass diffuser and the integrated hi-lo dimmer switch.

Betjening af dit lys

The XTL-1-HW/WH fixture is equipped with an integrated hi-lo dimmer switch for adjustable light output.

• Sådan tænder du: Tryk kontakten til 'ON'-positionen.
• Sådan justeres lysstyrken: The switch typically has a 'HI' and 'LO' setting. Select the desired brightness level.
• Sådan slukker du: Tryk kontakten til 'OFF'-positionen.

Opretholdelse

Udskiftning af pære

The Xenon bulb has an average life of 10,000 hours. When replacement is necessary:

1. Sluk for strømmen: Afbryd strømmen til armaturet ved afbryderen.
2. Open diffuser: Gently push the hinged frosted glass diffuser to open it. No tools are required.
3. Fjern den gamle pære: Carefully pull the old 18W T5 Wedge 12V Xenon bulb straight out of its socket.
4. Installer ny pære: Insert a new 18W T5 Wedge 12V Xenon bulb into the socket. Avoid touching the glass with bare hands; use a clean cloth or gloves if necessary.
5. Close diffuser: Close the frosted glass diffuser until it latches securely.
6. Genopret strøm: Tænd for strømmen igen ved afbryderen.

Rensning

To clean the fixture, ensure power is off. Wipe the exterior surfaces with a soft, dry cloth. For stubborn marks, a slightly damp cloth may be used, followed by drying. Do not use abrasive cleaners or solvents.

Fejlfinding

Produktspecifikationer

Garanti og kundesupport

For warranty information or technical assistance, please contact National Specialty Lighting customer support. Keep your purchase receipt as proof of purchase.

Kontaktoplysninger kan typisk findes på producentens officielle webwebstedet eller på produktemballagen.