Indledning
This manual provides essential instructions for the proper setup, operation, and maintenance of your Intermec SR30 Linear Imager RS232 Barcode Scanner. Please read this manual thoroughly before using the device to ensure optimal performance and to prevent damage.
The Intermec SR30 is a high-performance linear imager designed for reliable barcode scanning in various environments, connecting via an RS232 interface.
Sikkerhedsoplysninger
- Udsæt ikke scanneren for ekstreme temperaturer, fugtighed eller direkte sollys.
- Undgå at tabe scanneren eller udsætte den for kraftige stød.
- Do not attempt to open or modify the scanner. Refer all servicing to qualified personnel.
- Use only the power supply and cables provided or approved by Intermec.
- Hold scanningsvinduet rent for at sikre nøjagtig stregkodeaflæsning.
Pakkens indhold
Bekræft, at din pakke indeholder følgende varer:
- Intermec SR30 Linear Imager Barcode Scanner
- RS232-grænsefladekabel
- Strømforsyningsenhed
- Dokumentation (denne manual eller lignende)
Hvis der mangler eller er beskadigede varer, bedes du straks kontakte din leverandør.
Opsætning
1. Tilslutning af scanneren
- Tilslut RS232-kablet: Plug the RS232 connector of the interface cable into the corresponding serial port on your host computer or POS system.
- Connect to Scanner: Plug the other end of the interface cable into the port at the base of the SR30 scanner. Ensure a secure connection.
- Tilslut strømforsyning: Connect the power supply unit to the power port on the interface cable or directly to the scanner base, as applicable for your specific cable configuration. Plug the power supply into a standard electrical outlet.
2. Første opstart
Once connected, the scanner should power on automatically. Observe the indicator lights (typically an LED) for initial status. The scanner may emit a short beep to indicate it is ready for operation.
3. Basic Configuration (if required)
The SR30 scanner may require configuration for specific RS232 communication parameters (e.g., baud rate, data bits, parity) to match your host system. Refer to the detailed programming guide (often a separate document with programming barcodes) for advanced configuration. For basic operation, the default settings are often sufficient.
Betjening af scanneren
1. Scanning af stregkoder
- Sigte: Point the scanning window of the SR30 at the barcode you wish to read. Ensure the entire barcode is within the scanner's field of view.
- Scan: Press and hold the trigger button (if applicable) or present the barcode to the scanner's window for automatic scanning.
- Bekræftelse: A successful scan is typically indicated by an audible beep and/or a change in the LED indicator light (e.g., green light). The barcode data will be transmitted to your host system.
2. Forståelse af indikatorer
- Grøn LED: Indicates a successful barcode read.
- Red/Amber LED: May indicate an error, scanner busy, or awaiting input. Consult the full programming guide for specific error codes or patterns.
- Beep Sounds: Different beep patterns can indicate successful reads, errors, or configuration changes.
Opretholdelse
Rengøring af scanneren
- Rengør regelmæssigt scanningsvinduet med en blød, fnugfri kludamprengøres med vand eller et mildt, ikke-slibende rengøringsmiddel.
- Do not use harsh chemicals, solvents, or abrasive materials, as these can damage the scanner's surface.
- Sørg for, at scanneren er slukket, inden rengøring.
Opbevaring
Når scanneren ikke er i brug, skal den opbevares et rent og tørt sted, væk fra direkte sollys og ekstreme temperaturer.
Fejlfinding
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Scanneren tænder ikke. | Power cable not connected; power outlet faulty; power supply unit failure. | Check all cable connections. Try a different power outlet. Ensure the power supply is functioning. |
| Scanneren læser ikke stregkoder. | Barcode damaged or poorly printed; scanning window dirty; incorrect symbology enabled; scanner not configured for host. | Ensure barcode is clear. Clean scanning window. Verify scanner configuration matches host system requirements. Try scanning a known good barcode. |
| Barcode data not appearing on host. | RS232 cable loose or faulty; incorrect RS232 communication settings (baud rate, parity); host application not ready. | Check RS232 cable connection. Verify RS232 settings on both scanner and host. Ensure host application is active and ready to receive input. |
Specifikationer
- Model: SR30
- Varenummer: 225-727-003 (Kit)
- Scannertype: Lineær Imager
- Interface: RS232
- Fabrikant: Intermec
- Varens vægt: 0.01 ounces (approximate, scanner only)
- Afdeling: Stregkode
- ASIN: B003T0WF3S
Garanti og support
For warranty information and technical support, please refer to the documentation provided with your purchase or visit the official Intermec webwebsted. Behold din købskvittering som købsbevis i tilfælde af garantikrav.
Contact your reseller or Intermec customer service for assistance with issues not covered in this manual.