Indledning
The Bower SFD926N is an autofocus i-TTL power zoom flash unit designed for use with Nikon Digital SLR cameras. It features an auto-zoom flash head that adjusts to the camera's focal length, a built-in slave mode, and flexible tilt and swivel capabilities for comprehensive lighting control. This manual provides instructions for proper setup, operation, and maintenance of your flash unit.
Sikkerhedsforanstaltninger
- Do not attempt to disassemble or modify the flash unit. This can cause electric shock or damage the unit.
- Hold blitzenheden væk fra vand og fugt.
- Undgå direkte eksponering for blitzen i øjnene, især på tæt hold, da det kan forringe synet.
- Brug kun den angivne batteritype (4 AA-batterier). Bland ikke gamle og nye batterier eller forskellige typer batterier.
- Fjern batterierne, hvis blitzenheden ikke skal bruges i en længere periode.
Pakkens indhold
- Bower SFD926N Flash Unit
- Protective Pouch (if included)
- Mini-stativ (hvis inkluderet)
- User Information Sheet (basic guide)
Opsætning
1. Batteriinstallation
- Locate the battery compartment on the back of the flash unit.
- Åbn batterirummets dæksel.
- Isæt fire (4) AA-batterier, og sørg for korrekt polaritet (+/-) som angivet i batterirummet.
- Luk batterirummets dæksel forsvarligt.
Figur 1: Bagside view of the SFD926N flash unit, illustrating the control panel and the location of the battery compartment.
2. Tilslutning til kamera
- Sørg for, at både kameraet og blitzenheden er slukket.
- Skub flashenhedens monteringsfod ind i kameraets blitzsko.
- Tighten the locking wheel or lever on the flash unit to secure it firmly to the camera.
Figure 2: The Bower SFD926N flash unit securely mounted on a Nikon DSLR camera's hot shoe.
Betjeningsvejledning
Tænd/sluk
- To power on, slide the ON/OFF switch to the "ON" position. The LCD display will illuminate.
- For at slukke skal du skubbe ON/OFF-knappen til "OFF"-positionen.
- The unit features an auto power-saving illuminated LCD display.
Driftsformer
The SFD926N offers several operating modes:
- i-TTL (Through-The-Lens) Mode: This is the primary automatic exposure mode for Nikon cameras. The flash communicates with the camera to determine the optimal flash output. Ensure the flash is set to "ETTL" (or similar auto mode) and mounted on the camera's hot shoe.
- Manuel tilstand (M): Allows you to manually set the flash power output. Use the control buttons to adjust the power level (e.g., 1/1, 1/2, 1/4, etc.). This mode is useful for consistent lighting in studio setups or when off-camera.
- Slave Mode (S): The flash can be triggered wirelessly by another flash unit. Set the flash to "S" (Slave) mode. When another flash fires, the SFD926N will detect the light and fire simultaneously. This is useful for multi-flash setups without cables.
Adjusting Flash Head
The flash head can be adjusted for bounce flash photography:
- Vip: The flash head can tilt upwards from 0° to 90°. This allows you to bounce light off ceilings for softer illumination.
- Drejelig: The flash head can swivel horizontally from 0° to 270°. This allows you to bounce light off walls or adjust the direction of light when the flash is mounted on the camera.
Built-in Diffuser and Reflector Panel
- Vidvinkeldiffuser: Pull out the wide-angle diffuser panel from the flash head to spread the light for wider lens coverage.
- Reflektorpanel: Pull out the white reflector card from the flash head to create a catchlight in the subject's eyes or to provide a subtle fill light when bouncing the flash.
Synchronization Features
- Rødøjereduktion: This feature helps minimize red-eye effect in portraits. Refer to your camera's manual for activating red-eye reduction flash mode.
- Front Curtain Synchronization: The flash fires immediately after the shutter opens. This is the standard flash mode.
- Rear Curtain Synchronization: The flash fires just before the shutter closes. This creates a natural-looking trail of light behind moving subjects. Refer to your camera's manual for activating rear curtain sync.
Opretholdelse
- Rensning: Brug en blød, tør klud til at rengøre blitzenheden. Ved genstridigt snavs, tør letampen the cloth with water and wipe gently. Do not use solvents or abrasive cleaners.
- Opbevaring: Store the flash unit in a cool, dry place away from direct sunlight and extreme temperatures. Remove batteries if storing for an extended period to prevent leakage.
- Batteripleje: Brug altid nye AA-batterier af høj kvalitet. Udskift alle fire batterier på samme tid.
Fejlfinding
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Blitzen går ikke ud. |
|
|
| Flash fires inconsistently or stops firing after a few shots. |
|
|
| Flash unit does not charge or indicator lights do not illuminate. |
|
|
| Flimsy battery door. | Designkarakteristik. | Handle with care when opening and closing the battery compartment. |
Specifikationer
| Model | SFD926N |
| Kompatibilitet | Nikon Digital SLR Cameras (i-TTL compatible) |
| Vejledende nummer | 112 feet (85mm @ ISO 100) |
| Zoomområde | 24mm - 85mm (auto-zoom) |
| Flash-tilstande | i-TTL, Manual, Slave |
| Bounce/Swivel | Tilt: 0° to 90°, Swivel: 0° to 270° |
| Strømkilde | 4 x AA batterier |
| Dimensioner (ca.) | 6.25 x 2.1 x 3 tommer (15.9 x 5.3 x 7.6 cm) |
| Vægt (ca.) | 9.6 ounces (272 grams) without batteries |
| Særlige funktioner | Auto power saving LCD, Built-in diffuser and reflector panel, Red-eye reduction, Front/Rear curtain sync. |
Garanti og support
Bower products typically come with a limited manufacturer's warranty. For specific warranty details, please refer to any documentation included with your purchase or visit the official Bower website. In case of technical issues or warranty claims, please contact Bower customer support through their official channels. Information regarding customer service contact details may be available on the manufacturer's webwebsted.
Note: Some users have reported difficulty in finding direct customer service contact information. It is recommended to check the official Bower webwebsted for de mest aktuelle supportmuligheder.