Lee Precision 22 Horn Pacesetter Dies Instruction Manual

1. Produktet er slutview

The Lee Precision 22 Horn Pacesetter 3-Die Set is designed for reloading .22 Hornet cartridges. This comprehensive set provides the essential tools for resizing, bullet seating, and crimping operations, ensuring precise and consistent ammunition production. It is suitable for both novice and experienced reloaders seeking reliable performance.

Figur 1: The Lee Precision 22 Horn Pacesetter 3-Die Set, displayed in its protective red storage case. The image shows the Full Length Sizing Die, Bullet Seating Die, Factory Crimp Die, and a yellow powder dipper.

2. Inkluderede komponenter

The Lee Precision 22 Horn Pacesetter 3-Die Set includes the following items:

• Full Length Sizing Die: Used to return fired cases to factory dimensions for reliable chambering.
• Bullet Seating Die: Used to seat the bullet to the desired depth and can also apply a crimp.
• Factory Crimp Die: Provides a separate, precise crimp to secure the bullet, enhancing consistency and preventing bullet setback.
• Universal Shell Holder: Designed to hold the cartridge case during the reloading process.
• Powder Dipper: A volumetric measuring tool for dispensing powder.
• Instructions/Load Data: Detailed instructions for die setup and recommended powder charges for various bullet weights.

3. Opsætningsvejledning

Before beginning, ensure your reloading press is securely mounted and clean. Refer to the specific instructions included with your die set for detailed, step-by-step guidance tailored to your equipment.

3.1. Full Length Sizing Die Setup

1. Clean and lubricate a .22 Hornet case.
2. Thread the Full Length Sizing Die into your press until it touches the shell holder at the top of the ram's stroke.
3. Lower the ram and turn the die in an additional 1/4 to 1/2 turn. This ensures proper sizing.
4. Tighten the die lock ring.
5. Insert a case into the shell holder and raise the ram to size the case. Inspect the sized case for proper dimensions.

3.2. Bullet Seating Die Setup

1. With a primed and charged case in the shell holder, place a bullet on top.
2. Thread the Bullet Seating Die into the press until it contacts the bullet.
3. Adjust the bullet seating stem to achieve the desired overall cartridge length (OAL). Refer to your load data for recommended OAL.
4. Tighten the die lock ring.

3.3. Factory Crimp Die Setup

1. After bullet seating, place a loaded cartridge into the shell holder.
2. Thread the Factory Crimp Die into the press until it just touches the case mouth.
3. Lower the ram and turn the die in small increments (e.g., 1/8 turn) to apply the desired crimp.
4. Inspect the crimped cartridge to ensure the crimp is sufficient but not excessive.
5. Tighten the die lock ring.

4. Betjeningsvejledning

Always follow safe reloading practices. Consult the load data provided with your die set and reputable reloading manuals. Never exceed maximum powder charges.

1. Sagsbehandling: Clean and inspect all cases. Remove spent primers, size cases using the Full Length Sizing Die, trim to length if necessary, and deburr/chamfer case mouths.
2. Grunding: Insert a new primer into the case primer pocket.
3. Powder Charging: Use the included Powder Dipper or a precise powder measure to dispense the correct amount of powder into the case. Double-check powder charges.
4. Bullet Seating: Place a bullet onto the charged case and seat it to the correct overall length using the Bullet Seating Die.
5. Krympning: Apply a consistent crimp using the Factory Crimp Die to secure the bullet and ensure reliable feeding and ignition.
6. Afsluttende inspektion: Visually inspect each completed cartridge for defects, correct overall length, and proper crimp.

5. Vedligeholdelse

Proper maintenance ensures the longevity and performance of your reloading dies.

• Rensning: After each use, wipe down dies with a clean cloth to remove powder residue and lubricant. For deeper cleaning, disassemble the dies and clean with a suitable solvent, then re-lubricate.
• Smøring: Apply a thin coat of light oil to the exterior of the dies and internal moving parts (like the decapping pin assembly) to prevent rust and ensure smooth operation.
• Opbevaring: Store dies in their original protective case in a dry environment to prevent corrosion.
• Inspektion: Periodically inspect dies for wear, damage, or corrosion. Replace any damaged components immediately.

6. Fejlfinding

This section addresses common issues encountered during reloading with die sets.

• Difficulty Sizing Cases: Ensure cases are properly lubricated. Check if the sizing die is adjusted correctly (contacting the shell holder at the top of the ram's stroke, plus an additional turn).
• Bullet Not Seating Consistently: Verify the bullet seating stem is clean and free of debris. Ensure bullets are properly aligned before seating. Check for consistent case mouth tension.
• Inconsistent Crimp: Ensure the Factory Crimp Die is adjusted correctly and consistently. Check for variations in case length, which can affect crimp consistency.
• Stuck Case: This usually indicates insufficient case lubrication. Do not force the press. Refer to specific instructions for removing stuck cases, which often involves a stuck case remover tool.
• Primer Issues (Crushed, Not Seating): Check primer pocket cleanliness and size. Ensure the primer seating mechanism on your press is adjusted correctly.

For persistent issues, consult a comprehensive reloading manual or contact Lee Precision customer support.

7. Specifikationer

8. Sikkerhedsoplysninger

ADVARSEL: Dette produkt indeholder kemikalier, der af staten Californien vides at forårsage kræft og fødselsdefekter eller anden reproduktionsskade.

Reloading ammunition involves inherent risks. Always adhere to the following safety guidelines:

• Wear appropriate personal protective equipment, including safety glasses, during all reloading operations.
• Arbejd i et godt ventileret område.
• Keep all reloading components (primers, powder, bullets) out of reach of children and unauthorized individuals.
• Never smoke or have open flames near gunpowder.
• Follow all load data precisely. Never deviate from published data or exceed maximum charges.
• Ensure your reloading area is clean and organized to prevent errors.
• If you are unsure about any step, stop and consult a reputable reloading manual or an experienced reloader.

9. Garanti og support

For information regarding product warranty, technical support, or replacement parts, please refer to the documentation included with your Lee Precision product or visit the official Lee Precision webwebsted. Kontaktoplysninger til kundeservice findes typisk på producentens emballage eller webwebsted.