1. Introduktion
This manual provides essential information for the proper installation, operation, and maintenance of the Risco Lunar PIR 360 Degree Ceiling Motion Sensor (Model RK2000DPC). This device is designed to detect motion within a 360-degree field of view when mounted on a ceiling, utilizing passive infrared (PIR) technology. Please read these instructions carefully before proceeding with installation or use.
2. Sikkerhedsoplysninger
- Installation bør kun udføres af kvalificeret personale i overensstemmelse med alle lokale og nationale el-forskrifter.
- Afbryd strømmen til installationsområdet, før du udfører ledningsføring eller vedligeholdelse.
- Udsæt ikke enheden for fugt eller ekstreme temperaturer uden for det angivne driftsområde.
- Avoid mounting the sensor near heat sources, direct sunlight, or strong air currents, as these can cause false alarms.
- Sørg for korrekt jordforbindelse, hvor det er nødvendigt.
3. Pakkens indhold
Kontroller, at alle komponenter er til stede, før installationen påbegyndes:
- Risco Lunar PIR 360 Degree Ceiling Motion Sensor (RK2000DPC)
- Monteringsudstyr (skruer, ankre)
- Brugervejledning (dette dokument)
4. Opsætning og installation
The Risco Lunar PIR sensor is designed for ceiling mount installation. Optimal performance is achieved when mounted at a height of up to 4 meters (13 feet).
Figure 1: Risco Lunar PIR 360 Degree Ceiling Motion Sensor (RK2000DPC). This image shows the compact, low-profile design of the white circular sensor, suitable for discreet ceiling installation.
4.1 Monteringssted
- Choose a central location on the ceiling that provides the desired 360-degree coverage without obstructions.
- Avoid areas with direct drafts from HVAC vents or windows, as rapid temperature changes can trigger the sensor.
- Ensure the mounting surface is stable and can support the device.
4.2 Ledningsinstruktioner
The sensor operates on a DC voltage supply. Refer to the following specifications for wiring:
- Operation Voltage: 9 til 16 VDC
- Nuværende forbrug: 25mA på 12V
- Alarm Contacts: 100mA, 24V, N.C. (Normally Closed)
- Tamper Contacts: 100mA, 24V, N.C. (Normally Closed)
- Carefully open the sensor housing to access the terminal block.
- Connect the power supply wires to the designated terminals (typically marked + and - or VCC and GND).
- Connect the alarm output wires to your alarm control panel's zone input.
- Tilslut tamper switch wires to the control panel's tamper circuit, if applicable.
- Sørg for, at alle forbindelser er sikre og isolerede.
4.3 Initial Power-Up and Walk Test
- After wiring, carefully close the sensor housing.
- Apply power to the sensor. Allow a few minutes for the sensor to stabilize.
- Perform a walk test by moving through the detection area. The sensor features a Walk Test Display (1 LED) which will illuminate to indicate detection.
- Adjust the sensor's position or sensitivity if necessary to achieve optimal coverage and avoid false triggers.
5. Driftsprincipper
The Risco Lunar PIR sensor uses advanced passive infrared technology to detect changes in infrared energy caused by human body movement.
- Detection Technologies: Dual element PIR for enhanced reliability.
- PIR Lens Coverage: 110° angle, providing a full 360° overview from a ceiling mount.
- Registreringszoner: 60 zones, comprising 30 Fresnel facets arranged in 3 optical levels (12 external, 12 middle, and 6 internal facets) for comprehensive coverage.
- Justerbar følsomhed: Allows fine-tuning of the sensor's responsiveness to movement.
- Variable Pulse Count: Configurable setting (1, 2, or 3 pulses) to adjust the number of detected pulses required to trigger an alarm, helping to reduce false alarms.
- Temperaturkompensation: Automatic thermistor-controlled compensation ensures stable detection performance across varying ambient temperatures (0°C to 55°C / 32°F to 131°F).
- Optical Filtering: Provides white light protection to prevent false alarms from sudden changes in illumination.
- RF-immunitet: Designed with superior immunity to radio frequency interference (30V/m from 10MHz to 1GHz).
6. Vedligeholdelse
To ensure continued optimal performance of your Risco Lunar PIR sensor, follow these maintenance guidelines:
- Rensning: Periodically clean the sensor lens with a soft, dry, lint-free cloth. Do not use abrasive cleaners or solvents.
- Inspektion: Annually inspect the sensor for any physical damage, loose wiring, or obstructions to its field of view.
- Funktionstest: Perform a walk test periodically to confirm the sensor is detecting motion correctly.
7. Fejlfinding
If you encounter issues with your Risco Lunar PIR sensor, refer to the following common problems and solutions:
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Sensoren registrerer ikke bevægelse | No power; incorrect wiring; obstructed view; sensitivity too low; faulty sensor. | Check power supply and wiring; clear obstructions; increase sensitivity; perform walk test; contact support if sensor is faulty. |
| Falske alarmer | Heat sources (HVAC, sunlight); strong air currents; pets; sensitivity too high; incorrect pulse count setting. | Relocate sensor away from heat/drafts; adjust sensitivity; increase pulse count; ensure pets are not in detection area. |
| LED not illuminating during walk test | No power; LED malfunction; sensor not detecting. | Verify power; check wiring; perform walk test in different areas; contact support. |
8. Specifikationer
Detailed technical specifications for the Risco Lunar PIR 360 Degree Ceiling Motion Sensor (RK2000DPC):
- Mærke: Risco
- Modelnummer: RK2000DPC (also referred to as RK2000UPC in some documentation)
- Farve: Hvid
- Strømkilde: Elektrisk med ledning
- Operation Voltage: 9 til 16 VDC
- Nuværende forbrug: 25mA på 12V
- Alarm Contacts: 100mA, 24V, N.C.
- Tamper Contacts: 100mA, 24V, N.C.
- Detection Technologies: Dual element PIR
- PIR Lens Coverage: 110° angle, 360° overview
- Registreringszoner: 60 (30 Fresnel facets in 3 optical levels)
- Optical Filtering: Hvidt lys beskyttelse
- Selectable Pulse Count: 1, 2, 3
- Temperaturkompensation: Automatic thermistor-controlled
- RF-immunitet: 30V/m fra 10MHz til 1GHz
- Walk Test Display: 1 LED
- Driftstemperatur: 0°C til 55°C (32°F til 131°F)
- Opbevaringstemperatur: -20°C til 60°C (-4°F til 140°F)
- Dimensioner (diameter x højde): Ø135 x 27mm (Ø5.3" x 1.1")
- Installationshøjde: Op til 4 m (13 fod)
- Varens vægt: 4.8 ounce
- Monteringstype: Loftmontering
- UPC: 875586001303
- ASIN: B000GLY5O0
9. Garanti og support
Risco products are manufactured to high-quality standards. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official Risco website. For technical support, troubleshooting assistance, or service inquiries, please contact your authorized Risco dealer or distributor.
Hav din købskvittering og produktets serienummer ved hånden, når du kontakter support.